M12 CCS44 Original instructions
I II III IV V VI VII VIII IX 90° X Aufnahme aufschrauben XI Technical Data,Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
1. 2. 1. 2.
2-3 sec I 100 % 75 % 50 % 25 % 3
1. II 1 2 2.
3. II EN 847-1 4.
5. II 1 2 6.
^ III Insulated gripping surface 7
STOP START 1 III 2 For safety reasons this power tool is fitted with a switch lock and the On-/Off switch cannot be locked in the „On“ position 8
IV Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.
1. 2. IV 3.
1. 2. VI 50 45 40 30 20 0 10 3. 4.
1. 2. VI 2 1 3.
1. 2. START 1 VII 2 3. 45° 0° 4.
1. VIII 0° > 0° 2. 3. START 1 2 4. 14 5. 6.
A VIII B max.
90° 90° IX If a correction of the 90° angle of the guide-plate to the saw blade is necessary, use the correction screw. 1. 2.
90° 90° 3. IX + + – – 90° 4.
1. AS 2-250 4931 4472 95 B AS 300 / 500 4931 4472 94 2. A 2 1 X A B 1 3. 1 2 4.
TECHNICAL DATA Circular saw Production code M12 CCS44 No-load speed Saw blade dia. x hole dia Saw blade thickness Blade teeth Max. Cutting depth at 0° / 45° / 50° Battery voltage Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 6,0 Ah) Recommended Ambient Operating Temperature 4482 26 05 ... ... 000001-999999 3600 min-1 140 x 20 mm 1,0 mm 18T 44 / 33 / 27 mm 12 V 2,9 kg... 3,15 kg -18°C ... +50°C Recommended battery types M12B...
g) Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades that do not match the mounting hardware of the saw will run off-centre, causing loss of control. h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation. XI Lower guard function a) Check the lower guard for proper closing before each use.
WORKING INSTRUCTIONS Adapt the feed speed to avoid overheating the blade tips. TRANSPORTING LITHIUM BATTERIES Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. SPECIFIED CONDITIONS OF USE Transportation of those batteries has to be done in accordance with This electronic circular saw can cut lengthways and mitre accurately local, national and international provisions and regulations. in wood. The user can transport the batteries by road without further requirements.
EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives 2011/65/EU (RoHS) 2006/42/EC 2014/30/EU and the following harmonized standards have been used. EN 62841-1:2015 EN 62841-2-5:2014 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 SYMBOLS CAUTION! WARNING! DANGER! Please read the instructions carefully before starting the machine. Always wear goggles when using the machine.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
