Replacement Part List

Accessories and External Service Parts for the 2777-20 12T Overhead Cutter
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
61 14-34-0270 Side Handle Assembly (1)
61a --------------- Clamping Ring (1)
61b --------------- Handle Housing with Warning Label (1)
61c --------------- T-Bolt (1)
61d --------------- Side Handle (1)
61a 61b
61c 61d
61
61a
61b
61c
61d
1a
1h
10
1g
1f
1e
1d
1c
1b
1w
1a
1v
1k
1j
1m
1s
1r
1n
1t
1q
1p
1v
1u
1e 1t
1u
69
1n
1q
70
1b
10
71
1a 1f
1w 1x
72
1j 1r 1s
1v 32
73
1g
1h
77
1c 1d
1p
88
1x
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 --------------- Overhead Cutter Head Assembly (1)
1a --------------- Retaining Ring (2)
1b --------------- Blade Holder (1)
1c --------------- Blade (1)
1d --------------- M6 x 20mm Hex Drive Scr. w/ Washer (2)
1e --------------- Cutter Head Body (1)
1f --------------- 10mm Pin - Short (1)
1g --------------- Ball Spring Plunger (1)
1h --------------- Trip Lever (1)
1j --------------- 10mm Pin - Long (1)
1k 44-10-0590 Release Lever (1)
1m 44-20-0555 Latch Clip (1)
1n --------------- Thumb Screw (1)
1p --------------- Moveable Blade (1)
1q --------------- Pin Blade Connector (1)
1r --------------- Head Pin (1)
1s --------------- Spring (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1t --------------- Stop Ring (1)
1u --------------- M4 x 10mm Set Screw (1)
1v --------------- Retaining Ring (2)
1w --------------- Wave Spring (1)
10 --------------- M4 x 10mm Set Screw (1)
69 --------------- Clevis and Stop Set Screw Assembly (1)
70 44-60-0411 Blade Pin and Thumb Screw Kit (1)
71 43-72-0314 Fixed Blade Holder and Set Screw Kit (1)
72 44-10-0495 Short Pin Kit (1)
73 44-10-0505 Long Pin Kit (1)
77 44-10-0585 Trip Lever Assembly (1)
88 49-16-2775 Replacement OH Cutter Blade Set (1)
65 49-96-0012 Key Wrench (1)
83 12-20-0089 Service Nameplate (Not Shown) (1)
85 42-70-0027 Carabiner (Not Shown) (1)
86 48-22-8279 Accessory Utility Bag (Not Shown) (1)
TORQUE SPECIFICATIONS
Fig. kgf.cm in.lbs
1d 150 130
1n 15 13
1u 25 21
10 15 13
LUBRICATION
Type S2 Grease, 49-08-5265
1e 4g to the inside surface of the blade groove
on the Cutter Head Body.
1f Place a light coat (approx. 0.8g) to shaft of
10mm Pin-Short.
1j Place a light coat (approx. 0.8g) to shaft of
10mm Pin-Long.
1m Apply 1.6g to inside cavity of Latch Clip.
1q Place a light coat (approx. 0.8g) to shaft of
Pin Blade Connector.