User guide

21
966H Wheel Loader specifications
General Purpose Buckets
Teeth and Bolt-On Teeth and Bolt-On
Bucket Teeth Segments Edges Teeth Segments Edges
Rated Bucket Capacity (§)m
3
3.80 4.00 4.00 4.00 4.25 4.25
yd
3
5.00 5.25 5.25 5.25 5.50 5.50
Struck Capacity (§)m
3
3.28 3.43 3.43 3.43 3.62 3.62
yd
3
4.29 4.48 4.48 4.48 4.73 4.73
Width (§) mm 3145 3145 3059 3306 3306 3220
ft/in 10'4" 10'4" 10'0" 10'10" 10'10" 10'7"
Dump Clearance at Full Lift mm 2934 2934 3086 2934 2934 3086
and 45º Discharge (§) ft/in 9'8" 9'8" 10'2" 9'8" 9'8" 10'2"
Reach at Full Lift mm 1434 1434 1294 1434 1434 1294
and 45º Discharge (§) ft/in 4'8" 4'8" 4'3" 4'8" 4'8" 4'3"
Reach with Lift Arm Horizontal mm 2942 2942 2737 2942 2942 2737
and Bucket Level (§) ft/in 9'8" 9'8" 9'0" 9'8" 9'8" 9'0"
Digging Depth (§) mm 78 108 108 78 108 108
in 3.07 4.25 4.25 3.07 4.25 4.25
Overall Length mm 9080 9080 8855 9080 9080 8855
ft/in 29'9" 29'9" 29'1" 29'9" 29'9" 29'1"
Overall Height with Bucket mm 5853 5853 5853 5853 5853 5853
at Full Raise ft/in 19'2" 19'2" 19'2" 19'2" 19'2" 19'2"
Loader Clearance Circle with mm 14 778 14 778 14 572 14 924 14 924 14 720
Bucket in Carry Position (§) ft/in 48'6" 48'6" 47'10" 49'0" 49'0" 48'3"
Static Tipping Load Straight * kg 17 655 17 196 17 382 17 567 17 178 17 394
lb 38,929 37,917 38,327 38,735 37,877 38,354
Static Tipping Load kg 15 626 15 286 15 472 15 631 15 258 15 474
Full 37º Turn lb 34,455 33,706 34,116 34,466 33,644 34,120
Breakout Force ** (§) kN 200 186 188 200 186 188
lb 45,000 41,850 42,300 45,000 41,850 42,300
Operating Weight * (§) kg 23 610 23 762 23 622 23 674 23 865 23 698
lb 52,060 52,395 52,087 52,201 52,622 52,254
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including SAE Standard J732C
governing loader ratings.
* Static tipping loads and operating weights shown are based on standard machine configuration with 26.5R25 L-4 Firestone tires, roading fenders. powertrain
guard, full fuel tank, coolants, lubricants, air conditioner and operator.
** Measured 102 mm (4.0") behind ti
p
of cuttin
g
ed
g
e with bucket hin
g
e
p
in as
p
ivot
p
oint in accordance with SAE J732C.