Fluid Head OPERATOR’S MANUAL 1103 CiNX 3 Fluid Head 1105 CiNX 5 Fluid Head 1107 CiNX 7 Fluid Head
Contents Features and Controls............................................................................................................................................................................ 3 Introduction............................................................................................................................................................................................ 4 Safety Instructions.................................................................................
Features and Controls Camera Screws Camera Plate Pan Handle Side Load Lock Lever Tilt Lock Counterbalance Pan Handle Clamp Pan Lock Selector Pan Drag Control Illumination Button Bubble Level Tilt Drag Control CB Plus Selector Knob Tripod Bowl Threaded Stud Clamp Nut Fig. 1 3 Fig.
Introduction Safety Instructions Thank you for purchasing the CiNX 3/5/7 Fluid head. Attaching / removing the camera An impressive strength to size ratio makes the CiNX Fluid head ideal for use on feature films, documentaries and high-end television commercial productions that require mid-payload, frequent re-rigging and a diverse range of lenses and camera accessories. CiNX Fluid head features an Arri type side-loading camera platform.
Fig. 4 Operating Instructions 1. Attaching Mounting Base D150 Claw Ball D100 Claw Ball Fig. 4 3/8” Thread Mitchell Base Adapter Fig. 3 The CiNX Fluid head comes standard with a D100mm Claw Ball Adaptor which is attached using 3 off M5 x 12mm Socket Cap Screws (P4653) (fig. 3). A D150mm Claw Ball Adaptor (1290) and Mitchell Base Adapter (1225) is also available as an optional accessory (fig. 4). 5 Fig.
Operating Instructions 2. Camera Set-up Camera Plate 2.1 Remove the CAMERA PLATE by pulling and holding the SAFETY RELEASE PIN then pulling the SIDE LOAD LOCK LEVER outwards. Press the SAFETY LATCH BUTTON and remove the CAMERA PLATE from the BASE PLATE (Fig. 6). 2.2 Attach the CAMERA PLATE to the camera and securely tighten the screws. Refer to the Camera’s owner’s manual for correct method of attachment to the CAMERA PLATE. 2.
Operating Instructions 2.4 Align the edge of the CAMERA PLATE with the PLATFORM, and then side load the CAMERA PLATE into the PLATFORM. Once the CAMERA PLATE is in position an audible sound will be heard. At this point, the CAMERA PLATE can slide forward / backward only. To release the camera plate press the safety latch button. C of G 2.5 Position the CAMERA PLATE such that the camera’s C of G is directly above the centre axis of the Fluid head, (fig.
Operating Instructions 3. Camera Plate Lock Adjustment 3.1 The Camera Plate Lock is designed to secure the CAMERA PLATE in a set position. The CiNX PLATFORM can accept a third party (Arri type) CAMERA PLATE, however, the Camera Plate Lock may need to be adjusted to account for small dimensional variations in third party CAMERA PLATES that can significantly affect the locking function. Locking Screw Adjusting Screw 3mm Hex Key 3.
Operating Instructions Turn adjustment screw counterclockwise to compensate for a wider camera plate. Turn adjustment screw clockwise to compensate for a narrower camera plate. Platform Platform Correct position of Side Load Lock Lever at the start of locking action. Platform Fig.
Operating Instructions 4. Counterbalance Control The counterbalance system was designed to neutralise the effect of the camera weight when it is tilted. The CiNX Fluid head offers a 16 position counterbalance system which is operated with the CB SELECTOR KNOB and the CB PLUS SELECTOR KNOB. The system was designed for an efficient and ergonomic control of the counterbalance mechanism which delivers a wide payload range capacity.
Operating Instructions 5. Pan-tilt Drag Control Illumination Button The CiNX 5 & 7 Fluid head offers 7 selectable positions of fluid drag + zero setting in the Pan and Tilt. The settings are equally stepped from light drag in position 1 up to heavy drag in position 7, the drag plates are completely disengaged in position zero. The CiNX 3 offers 5 selectable positions of Fluid drag + zero setting.
Maintenance The CiNX Fluid head offers high quality surface coatings, dust and moisture seals. Miller recommends keeping the Fluid head clean at all times by using soft brushes and lint free cloth to wipe over the surfaces. Illumination Button • Do not immerse the Fluid head in any liquid. • Do not use stiff brushes, abrasives, harsh detergents and solvents. Battery Replacement The CiNX Fluid head uses a single GP23A type - 12 Volt battery for Illumination.
Specifications 1103 CiNX 3 1105 CiNX 5 1107 CiNX 7 Weight 3.8kg (8.4lbs) 4.1kg (9.0lbs) with 100mm bowl 4.0kg (8.8lbs) 4.3kg (9.5lbs) with 100mm bowl 4.0kg (8.8lbs) 4.3kg (9.5lbs) with 100mm bowl Payload range 1-19kg (2.2-41.8lbs) 2-21kg (4.4-46.2lbs) 6-25kg (13.
Specifications Counterbalance Performance Counterbalance Performance C of G above Camera plate (mm) 1105 CiNX 5 C of G above Camera plate (mm) 1103 CiNX 3 Payload Range 1-19kg (2.2-41.8lbs) Payload Range 2-21kg (4.4-46.2lbs) 1107 CiNX 7 C of G above Camera plate (mm) Counterbalance Performance Payload Range 6-25kg (13.2-55.
Storage Service, Sales and Support The CiNX Fluid head can be stored for extended periods; Miller recommends storage in a Miller Case and the following: • Remove battery. • Clean the external surfaces. • Keep in a dry place away from direct sunlight. • Loosen off PAN & TILT LOCK. Spare Parts and Accessories ITEM ITEM NO.
millertripods.com MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon, Sydney NSW 2064 Australia Tel: +61 2 9439 6377 Fax: +61 2 9438 2819 Email: sales@miller.com.
