SLS300 lighting stand user manual
Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 10.01.
Table of contents Table of contents 1 General information................................................................................................................................. 4 2 Safety instructions..................................................................................................................................... 6 3 Features .....................................................................................................................................................
General information 1 General information This manual contains important instructions for the safe operation of the product. Read and follow the safety instructions and all other instructions. Keep the manual for future reference. Make sure that it is available to all those using the product. If you sell the product to another user, be sure that they also receive this manual. Our products are subject to a process of continuous development. Thus, they are subject to change.
General information Signal word Meaning DANGER! This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided. CAUTION! This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in minor injury if it is not avoided.
Safety instructions 2 Safety instructions Intended use This light stand is intended to be used for the stable mounting and height-adjustable posi‐ tioning of spotlights. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
Safety instructions Safety DANGER! Danger for children Ensure that plastic bags, packaging, etc. are properly disposed of and are not in the reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the product. They could swallow the pieces and choke! Never let children play unattended with the product.
Safety instructions CAUTION! Danger of tipping on unsuitable surfaces When the speaker stand is installed on soft or uneven ground, the stand may tip over and cause injuries and property damage. Install the stand only on even and solid surfaces. CAUTION! Danger of tipping due to overload In case of overload, the stand may tip over and cause injuries and property damage. Never exceed the maximum load capacity specified for the stand.
Features 3 Features Special features: n n n n n Quick and easy assembly 3 m wide crossbar, optionally expandable to max. 4.
Operating 4 Operating Unpack and check carefully there is no transportation damage before using the product. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
Operating CAUTION! Danger of tipping on unsuitable surfaces When the speaker stand is installed on soft or uneven ground, the stand may tip over and cause injuries and property damage. Install the stand only on even and solid surfaces. CAUTION! Danger of tipping due to overload In case of overload, the stand may tip over and cause injuries and property damage. Never exceed the maximum load capacity specified for the stand.
Operating NOTICE! Possible staining The plasticiser contained in the rubber feet of this product may possibly react with the coating of your parquet, linoleum, laminate or PVC floor and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the floor, but use felt-pad floor protectors or a carpet. Comply with regulations When installing and operating, make sure to follow the standards and regulations that apply in your country.
Operating Scope of delivery Before you assemble your lighting stand, make sure the contents of package is complete according to the following list: 1. Truss section A (2 ×) 2.
Operating 3. Pipe C without screw joint (1 ×) 4.
Operating 5.
Operating 6.
Operating 7.
Operating Assembly Basically you can carry out the following steps on your own. But with the assistance of a second person the assembly will be much easier. 1. Remove the rubber caps from the ends of the truss sections (A).
Operating 2. Attach the two T-pieces (B) to the ends of tube (C). 3. Plug the combination of (B) and (C) on the open side of a truss section (A). Then slide the tubes (D) through the T-pieces (B) into truss section (A) and screw the tubes (D).
Operating 4. Plug the second truss section on the open end and screw it.
Operating 5. Insert the T-pieces (E) on the outer ends of the two truss sections (A).
Operating 6. Secure the T-pieces (E) with the safety bolts.
Operating 7. Unfold the feet of the tripod until the cross braces are in a horizontal position. 8. Fix this position with the safety screw on the slider to which the three feet are attached. 9. Pull out the safety bolt and loosen the locking screw on the extension tube. 10. Pull out the extension tube to the desired height, insert the safety pin through the appropriate grid holes and slide the safety cotter through the hole in the safety bolt. 11.
Operating 12. Plug the truss with the T-pieces onto the extension tube of the stands and attach the truss to the T-pieces (E) with the Allen screws. 13. Mount the headlight (s), if necessary with adapters, on the crossbar. Observe the instruc‐ tions of the respective manufacturers. The maximum load capacity of the traverse of 25 kg (18 kg per tripod) must not be exceeded.
Operating Dismounting 1. Remove the spotlight(s). 2. Loosen the Allen screws on the T-pieces (E) at the ends of the truss and pull the truss off the stands. 3. Disassemble the truss in the reverse order of the assembly instructions as far as it makes sense for a transport or storage in view of a new assembly. 4. Pull out the safety bolt on the stand and hold the extension tube while you loosen the locking screw on the extension tube. 5.
Technical specifications 5 Technical specifications Height, max. 2.65 m Total width 3,00 m Adjustable tripod height 1.20 m … 2.65 m Footprint Æ 1.34 m Single truss length 2 × 1.50 m, optionally expandable to 4,50 m max. Tripod tube diameter Æ 38 mm Truss tube diameter Æ 38 mm Pipe spacing, truss (outside) 27 cm Holder type C03 hook (item no. 145665) for attaching lamps to the crossbar Total system load, max. 25 kg Load per tripod, max.
Technical specifications Weight 12 kg Colour black Further information Stand type Background Kit incl.
Protecting the environment 6 Protecting the environment Disposal of the packaging mate‐ rial For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes SLS300 29
Notes lighting stand 30
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
