Assembly Instructions MPS-850 E-Drum Set
Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 27.06.
Table of contents Table of contents 1 Safety instructions.......................................................................................................................................................................................................... 5 2 Scope of delivery.............................................................................................................................................................................................................. 6 3 Assembly......
MPS-850 E-Drum Set
Safety instructions 1 Safety instructions DANGER! Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Scope of delivery 2 Scope of delivery Before you assemble your drum set, make sure the contents of package is complete according to the following list and figure. Item Qty.
Scope of delivery Item Qty.
Scope of delivery ö $ (2 ×) # % (3 ×) ( + 0 6 7 MPS-850 E-Drum Set ' * - 2 (2 ×) 8 (5 ×) .
Assembly 3 Assembly Overview Loosen the screws of the clamps before sticking the tubes together. Mount the various elements in the specified sequence. The final positions of the components are shown in the illustration below. 3 2 2 4 + 1 .
Assembly Assembling the rack CAUTION! Danger of cuts on hands and fingers When connecting the parts, take care for sharp edges on the metal tubes, screws etc. : & ö ' 1. Attach the horizontal connection tubes (5, 6) to the lateral support tubes (1, 2). 2. Then tighten the mounting screws with the drum key (25). ( $ * # ) $ 1. Attach the two side crossbeams of the rack (7, 8, 9) in the provided mounting clamps. 2. Attach the crossbeam support tubes (3) in the provided mounting clamps.
Assembly 3. Then tighten the mounting screws. 9 9 9 9 9 1. Position the mounting brackets (24) for the individual pads. Then tighten the mounting screws. 2. Turn the mounting brackets (24) in the right position for mounting the pads. Then tighten the mounting screws. % % % 1. Insert the brackets (4) for the cymbals (Crash, Ride) into the provided mounting clamps on the rack. Fasten the brackets using the mounting screws at the desired height. 2.
Assembly Mounting pads on the rack + + , , 1. Attach the mounting brackets to the pads (10, 11, 12). Tighten the wing nuts on the pads by hand first. 2. Then slide the plastic ends of the mounting brackets up to the stop into the designated clamps on the rack. 3. Align the pads on the rack to meet your needs, then tighten the wing nuts of the pad brackets and the bolts of the pad clamps on the rack evenly. Mounting cymbals on the rack 1.
Assembly Setting up the bass drum pedal 7 6 8 1. Snap the two metal rods into the holes provided on the frame of the bass drum pedal. 2. Place the beater (22) into the hole provided on the rotary head of the pedal (21) and tighten the clamp with the drum key. Aligning the beater Pay attention to the correct orientation of the beater. The beater may only hit the bass drum pad with the black plastic side.
Assembly Assembling the Hi-hat stand Assemble the hi-hat stand as shown below. To attach the hi-hat controller and hi-hat to the hi-hat stand, complete the following steps. 1. Loosen the Allen screw on the hi-hat connector piece with the drum key. Turn the top counterclockwise and remove the items upwards. 2. Put the hi-hat on the lower part of the connector piece. Put the parts removed in the previous step back onto the connector piece and retighten the Allen screw. 3.
Assembly Set-up and cabling Set up the rack, the pads and the cymbals according to your needs. Finally, position the drum pedal and the Hi-hat controller in front of the rack and connect all trigger cables to the e-drum module.
Protecting the environment 4 Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes MPS-850 E-Drum Set 17
Notes 18 MPS-850 E-Drum Set
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
