Assembly Instructions MPS-750X E-Drum Set
Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 17.06.
Table of contents Table of contents 1 Safety instructions.......................................................................................................................................................................................................... 5 2 Scope of delivery.............................................................................................................................................................................................................. 6 3 Assembly......
MPS-750X E-Drum Set
Safety instructions 1 Safety instructions DANGER! Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Scope of delivery 2 Scope of delivery Before you assemble your drum set, make sure the contents of package is complete according to the following list and figure. Item Qty.
Scope of delivery ö # $ % & ' ( (2 ×) (2 ×) (2 ×) (2 ×) + * ) (4 ×) (2 ×) - , .
Assembly 3 Assembly Overview Loosen the screws of the clamps before sticking the tubes together. Mount the various elements in the specified sequence. The final positions of the components are shown in the illustration below. .
Assembly Assembling the rack CAUTION! Danger of cuts on hands and fingers When connecting the parts, take care for sharp edges on the metal tubes, screws etc. % ö 1. Attach the clamp (4a) of the snare crossbeam (4) to one of the two lateral support tubes (1). 2. Then tighten the wing nut of the clamp (4a). $ ö ö 1. Fasten the two lateral support tubes (1) in the fastening clamps of the horizontal connecting tube (3). 2. Then tighten the wing nuts of the fastening clamps.
Assembly % ö 1. Attach the crossbeam for the snare (4) to the left support tube (1). 2. Then tighten the wing nut of the fastening clamps. & & ö 1. Attach the two crossbeams (5) to the two lateral support tubes (1). 2. Then tighten the wing nuts of the fastening clamps.
Assembly & & # # 1. Fasten the two support tubes for the crossbeams (2) in the fastening clamps of the crossbeams (5). 2. Then tighten the wing nuts of the fastening clamps. ' ö ö 1. Fasten the two lateral support tubes (1) in the fastening clamps of the horizontal connecting tube (6). 2. Then tighten the wing nuts of the fastening clamps.
Assembly ( ( ) ) ö ö 1. Attach the two connections for the cymbal holder (8) and the cymbal holder (7) to the two lateral support tubes (1). 2. Then tighten the wing nuts of the fastening clamps.
Assembly + * ' * * , % & , , * 1. Attach the sleeve for the mounting bracket (9) and the mounting bracket (10) in the bracket for the snare on the crossbeam (4). 2. Then attach the sleeves for the mounting rods (9) and the mounting rods (11) in the holders for the tom pads on the right crossbeam (5) and on the horizontal connecting tube (6). 3. Then tighten the wing nuts of the brackets. Mounting tom pads on the rack 0 1 , + 1.
Assembly Mounting cymbals on the rack . / ( 1. Unscrew the wing nuts from the cymbal holders (7) and take the felt washers off the holders. 2. Place the cymbals (13, 14) as shown in the figure on the holders. Be sure to attach the crash pad (12") to the left holder and the ride pad (14") to the right cymbal holder. 3. Place the felt washers on the cymbals (13, 14) and fix the cymbals with the associated wing nuts on the holders.
Assembly Mounting the Hi-hat on the rack 5 4 1. Screw on the wing nuts of the hi-hat tripod with pedal (19) and open the feet. Then tighten the wing nuts of the brackets. 2. Insert the hi-hat holder (20) into the hi-hat tripod with pedal (19) and tighten the holder clockwise. 3. Unscrew the wing nuts from the Hi-hat holder (20) and take the felt washers off the holders. 4. Place the Hi-hat (12) as shown in the figure on the holder. 5.
Assembly Mounting the drum module on the rack 1. Put the drum module (21) up to the stop into the free bracket of the left crossbeam (5). Insert the D-sub plug of the multiple cable (22) into the provided socket on the bottom side of the drum module. 2. Tighten the D-sub plug with the hand screws. 3. Align the module and tighten the wing nut of the bracket. Bass Drum positioning Place the pedal with the bass drum pad centred under the rack. Position the bass drum pedal centred in front of the pad.
Protecting the environment 4 Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes 18 MPS-750X E-Drum Set
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
