Assembly Instructions MPS-1000 E-Drum Set
Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 17.06.
Table of contents Table of contents 1 Safety instructions.......................................................................................................................................................................................................... 5 2 Scope of delivery.............................................................................................................................................................................................................. 6 3 Assembly......
MPS-1000 E-Drum Set
Safety instructions 1 Safety instructions DANGER! Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Scope of delivery 2 Scope of delivery Before you assemble your drum set, make sure the contents of package is complete according to the following list. Qty.
Assembly 3 Assembly Overview Loosen the screws of the individual clamps before assembling. Mount the various elements in the specified sequence. The final positions of the components are shown in the illustration below. ö , - / + .
Assembly Bass drum and Tom pads CAUTION! Danger of cuts on hands and fingers When connecting the parts, take care for sharp edges on the stands, screws etc. ' & ( & & % # ö $ 1. Fasten the two bass drum spurs (1) to the bass drum (2) with the wing nuts of the fastening clamps. 2. Fasten the bass drum pedal (3) to the hoop of the bass drum (2), place the pedal in the appropriate position and attach it to the pedal with the wing nut. 3.
Assembly Floor tom * ) 1. Fasten the three floor tom spurs (8) to the tom (9) with the wing nuts of the fastening clamps and hand-tighten them. 2. Align the floor tom spurs (8) according to your needs and then tighten the wing nuts of the fastening clamps evenly. Snare pad - , . + 1. Loosen the wing nut of the spurs of the snare stand (10), align it according to your needs and then tighten the wing nut again. 2.
Assembly Hi-hat pad 9 / 3 1 2 1 7 0 8 4 5 6 1. Unscrew the wing nut (14) from the bracket (15) and remove the felt washers (16) and the round nuts (18) from the bracket. 2. Place the two felt washers (16), the hi-hat pad (17) and the round nuts (18) on the holder one after the other, as shown in the illustration. 3. Then tighten the wing nut (14). 4. Unscrew the wing nut (20) of the hi-hat stand (19) with pedal (21) and open up the legs. Then tighten the wing nut (20) again. 5.
Assembly Drum module : ; < 1. Place the drum module (25) on the module plate (26) and screw them together with the supplied screws. 2. Guide the module plate (26) into the drum module holder (27) and then tighten the wing nut of the drum module holder to fix the drum module.
Assembly Cymbals I H G F E D B C ? A > = 1. Unscrew the wing nut (28) of the boom cymbal stand (29) and open up the legs. Then tighten the wing nut (28) again. 2. Insert the bracket (30) into the boom cymbal stand (29) as shown in the illustration. 3. Adjust the height of the bracket (30) according to your needs and then tighten the wing nut (31). 4. Unscrew the wing nut (32) of the boom arm (33) and adjust the position of the boom arm (33) according to your needs.
Assembly Set-up and cabling Set up the stands and pads according to your needs. All drum and cymbal pads are wired with the multiple cable supplied. The plugs are appropriately labelled. The second crash pad is wired to the e-drum module via the additional jack cable. The tension of the mesh heads is relatively low in the delivery state in order to avoid damage during transport. For good playability and better trigger behaviour, adjust the drum head tension to your playing habits.
Protecting the environment 4 Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
