Assembly Instructions Focus Junior Drum-Set Drum Set
Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 17.06.2022, ID: 496064, ...
Table of contents Table of contents 1 Safety instructions................................................................................................................. 5 2 Note............................................................................................................................................... 6 3 Unpacking.................................................................................................................................. 7 4 Setting up the bass drum.........
Focus Junior Drum-Set Drum Set
Safety instructions 1 Safety instructions DANGER! Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Note 2 Note This document is a general guide showing typical steps for setting up a drum set. Depending on the model, there can be variations in the type and number of components.
Unpacking 3 Unpacking Assigning The following guide makes it easy for you to completely assemble your drum set, to tune it and to set it up properly. The complete drum set is supplied in one cardboard box. It is supplied dismantled in its individual parts. We recommend that you first sort the individual parts that belong together as described below. Snare drum The snare drum is delivered fully assembled. The drum heads are already fitted.
Unpacking Floor tom The floor tom includes the following parts: n n n n n Hardware package 1 drum shell 2 hoops 2 heads 10 tension rods with one washer each 3 spurs The hardware package includes the following parts: 1 bass drum pedal 1 hi-hat stand 1 snare stand 1 straight cymbal stand 8 Focus Junior Drum-Set Drum Set
Unpacking 2 tom holders Accessories The accessories include the following parts: n 1 tuning key n 1 pair of drumsticks Cymbals Depending on the scope of supply, a set of cymbals is included: n 1 crash / ride cymbal (12 inch) n 1 hi-hat cymbal (10 inch) Focus Junior Drum-Set Drum Set 9
Setting up the bass drum 4 Setting up the bass drum Let's start with the bass drum. Position the bass drum shell such that the screws of the tom holder point down‐ wards. Now lay the white resonator head on the shell and put a hoop over it. Both the hoops are identical so it doesn't matter which one you put on first. Align the white reso‐ nator head such that the "Millenium" writing is parallel to the tom holder. The head must be lying evenly on the edge of the shell on all sides.
Assembling the floor tom 5 Assembling the floor tom The principle of assembling the floor tom is basically the same as with the bass drum. The shell is smaller which means that they don't have as many tension rods. The hoops are made of steel. This means that they don't need any claw hooks; rather, you screw them on directly. The tension rods aren't as long as with the bass drum either, since the hoops are not as wide.
Assembling the bass drum pedal 6 Assembling the bass drum pedal Let's concentrate on the hardware first. You have to assemble the bass drum pedal first. The flat rod below the pedal must be pushed forward into the holder and then fas‐ tened with the screw. Now you screw the beater into the holder. NOTICE! Do not stick the bottom end of the shaft in too far; otherwise, it could damage the bass drum head. You can make all the other settings later on.
Assembling the hi-hat 7 Assembling the hi-hat Pull the stand's three legs far enough apart until there is optimum stability between the base point of the stand and the legs. A wing nut ensures that the legs do not move out of position. As with the bass drum pedal, the hi-hat's pedal is stabilized by pushing the pedal for‐ ward into the holder and then fastening it with the screw. The next thing to do is to tightly screw home the pull rod in the stand's thread.
Assembling the cymbal stands 8 Assembling the cymbal stands The legs of the straight cymbal stand are folded out or extended until it stands secure. After this, you fix the legs using the wing nut. Push the centre and spacer tubes onto the bottom case and fix them with the wing screws. We will make the final settings later on. The cymbal holder is directly on the retractable spacer tube. You attach the cymbals in exactly the same way as with the hi-hat-stand after positioning.
Assembling the snare drum stand 9 Assembling the snare drum stand In the case of the snare drum stand too, you fold out the three legs and fix them with wing nut. Now put the top part with the arms into the lower section and screw it tight. Screwing down the union nut opens the support arms. The union nut on the joint allows you to set the angle of the drum. Here too, we will make all the necessary set‐ tings later on when positioning the set.
Tuning the shells 10 Tuning the shells All the drum shells are mounted. All the hardware is assembled. Basics Always tighten the tension rods in the diagonally opposite sequence to ensure even tension. You should tighten all the screws evenly. At the beginning, don't turn the screw by more than one rotation – towards the end, rotate by ¼ to ⅛ of a turn. Then check the pitch. You check the pitch by tapping the head about 3 cm from the rim near the screw that you are just setting.
Tuning the shells The sounds of the three toms should also harmonise. The sounds should harmonise while you're tuning the heads. Don't be afraid to play the other two toms to ensure that the tones harmonise. Don't tune the resonator heads until you have tuned the heads on all three toms. You tune the batter and resonator heads to the same pitch. This considerably amplifies the drums' sounds.
Setting up the drum set 11 Setting up the drum set For optimum playing, we don't just need tuned drums; rather, it is also necessary to position all the drums in an optimum way. We now make all the settings that we neglected before. The set-up that is described here is intended for right-handers. The set-up for left-handers is a mirror image of this one. A non-slip surface like a carpet or similar guarantees stability. Drum stool Let's start with the drum stool.
Setting up the drum set Now you can push the assembled bass drum pedal onto the clamping ring and fix it with the claw. Use some gaffa tape to protect the hoop from scratching. Now, there's only the tom racks. There are different designs. The tom holder – that's the clamp for the tom arms on the bass drum – is intended for one or two tom arms. This means that if only one tube fits in, there is an adapter for both tom arms. Our tom holder takes both tom arms directly.
Setting up the drum set The hanging toms are next. Put each tom shell in the bracket arm and screw it tight. The tom shells are drilled through and the bracket arms are pushed into the shell. Mount the smaller tom to the left of the drummer and the larger one to their right. As with the snare drum the heights and angles of the toms depend on the height at which the drummer is seated. In this connection, it should be possible to play the drumstick as parallel as possible to the head.
Attaching the cymbals 12 Attaching the cymbals Our drum set is starting to take shape. We've already found the position of the hi-hat stand. What's missing now is attaching the hi-hat cymbals and adjusting the height. Attaching the hi-hat cymbals First place a metal washer and the felt disk on the hi-hat stand. Then the bottom cymbal (labelled "bottom"). Lie it freely onto the stand's felt disk. We have to make some preparations for the top cymbal (labelled "top").
Attaching the cymbals Now all the parts are in place and you can start to play. Have lots of fun with your new drum set.
Protecting the environment 13 Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes 24 Focus Junior Drum-Set Drum Set
Notes Focus Junior Drum-Set Drum Set 25
Notes 26 Focus Junior Drum-Set Drum Set
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
