ASSEMBLY AND INSTRUCTION MANUAL (EN) Series: Convection Please read the instructions carefully before use. Take good care of this manual for later use.
Important safety information You must obey common safety guidelines when using electrical products, especially in the presence of children. WARNING! To avoid electric shock or damage due to the heat, always make sure the plug is pulled out before the heater is moved or cleaned. Read the instructions carefully. The product is intended for home use only. Make sure the heater is connected to the house's regular mains (230 V), as it indicated on the heater.
The device cannot be used by children under 8 years of age and persons with reduced physical or mental abilities or lack of experience and knowledge unless they have been given supervision or instruction in the safe use of the device and understand the hazards involved. Children should not play with the device. Cleaning and maintenance should not be done by unsupervised children. Children under the age of 3 should be kept away from the device, unless they are under constant supervision.
STORE THIS INSTRUCTION MANUAL FOR FUTURE USE! NEVER TOUCH YOUR PANEL HEATER OR ITS CASING WITH WET HANDS! Specifications Model SG2000MEC SG2000LED SG2000GLASS Thermostat Mechanical Electronic Electronic Color White White White Amperage ~230 V / 50 Hz ~230 V / 50 Hz ~230 V / 50 Hz Power (W) 2000 2000 2000 Fan No Yes Yes Before first use After unpacking the heater, check to make sure the product was not damaged during transport.
SG2000MEC 1. Heat emission 2. Thermostat 3. Output selector 4. Legs (plastic) Description of the heater SG2000LED/SG2000GLASS 1. Heat emission 2. LED display 3. Thermostat + output selector 4. Fan 5. ON/OFF 6. Legs (aluminium) Parts SG2000MEC 4 screws (pre-mounted) 2 foot brackets 2 rails for the feet Parts SG2000LED/SG2000GLASS EN 8 screws (4 of which are pre-mounted) 2 foot brackets 2 rails for the feet 5 millheat.
Assembly SG2000MEC 1. Insert both legs into the brackets so you get a stable foot (as shown in Picture 1 below). 2. Remove the pre-mounted screws from the bottom of the heater and place the heater gently on its head to mount the feet. 3. Two screws must be fastened on each foot bracket (as shown in Picture 2 below). 4. NEVER USE THE HEATER BEFORE THE LEGS HAVE BEEN TIGHTLY SCREWED. Assembly SG2000LED/SG2000GLASS EN 1.
SG2000MEC – Instructions CAUTION! This heater is only designed to be used for supplementary heating, and as such must only be used under supervision Control panel for SG2000MEC 1. Thermostat. Adjust the desired heat setting 2. Output selector: 0: OFF |: 750 W ||: 1250 W |||: 2000 W WARNING: Be sure the foot is fitted correctly and according to the instructions before using the heater! Use 1. Set the output selector to the OFF position (0) and the thermostat to minimum.
SG2000LED/SG2000GLASS – Instructions CAUTION! This heater is only designed to be used for supplementary heating, and as such must only be used under supervision Control panel for SG2000LED/SG2000GLASS Display SG2000LED SG2000LED SG2000GLASS Display SG2000GLASS 1. Thermostat and output selector: i. Turn the selector to the left to decrease the temperature, and turn the selector to the right to increase the temperature. ii. Push the button to change the desired power level.
Using SG2000LED/SG2000GLASS 1. Plug the heater into a grounded outlet. 2. Press the ON/OFF button. 3. Choose the desired power |, || or |||, by pressing the output selector. Turn the thermostat to the desired temperature while looking at the display. As soon as the room temperature drops below this level, the heater will automatically start again. When the room has reached the desired temperature again, the heater will turn itself off. 4. The thermostat goes from 5 to 35°C. 5.
Maintenance 1) For cleaning, always unplug the heater and leave it to cool. 2) Wipe the heater regularly with a damp cloth and dry the surface before turning on the heater again. 3) The heater must be cleaned at least once a month during the heating season. CAUTION! The heater should never be immersed in water. Avoid using detergents to clean the heater. Never let any water get inside the heater; this can be hazardous. 4) Dust etc. should be removed with a soft cloth.
