User’s Manual for MIL-S801XX
Regulatory Approval - FCC Class A - UL 1950 - CSA C22.2 Number 950 - EN60950 - CE - EN55022 Class A - EN55024 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
Contents 1. Introduction Features Package Contents 2. Hardware Description Front Panel MIL-S801XX 9 port switch with SC fiber port MIL-S801XX 9 port switch with SC (Single-mode) fiber port MIL-S801XX 9 port switch with ST fiber port MIL-S801XX 9 port switch with MT-RJ fiber port MIL-S801XX 9 port switch with VF-45 fiber port Rear Panel Desktop Installation 3. Network Application Desktop Application Segment Application 4. Trouble Shooting Diagnosing LED Indicator Power Transmission Mode 5.
1. Introduction MiLAN’s MIL-S801XX switch with a fiber port is a compact desktop size switch, which is an ideal solution for many network users. It provides wire-speed, Fast Ethernet switching function that allows highperformance, low-cost connections. Figure 1. The MIL-S801XX The MIL-S801XX nine port switch provides 8 switched auto-sensing 10/100 Mbps RJ-45 Ethernet ports and one 100BASE-FX fiber port. The switch combines both 10BASE-T and high-speed 100BASE-TX support in one device.
Features • • • • • • • • • • • Eight 10/100Mbps Fast Ethernet UTP switch ports One 100Mbps multi-mode port (SC, ST, MT-RJ, VF-45) or single-mode SC port One DIP-switch to select fiber port full-duplex or half-duplex mode Auto-negotiation for full or half duplex Store-and-forward switching architecture for packet filtering Full wire speed forwarding rate 4K-entry MAC address table 256KB memory buffer sharing LED-indicators for power, 100M, LK/ACT, FD/COL statuses Compact size Eight auto-sensing MDI/MDIX por
2. Hardware Description This Section mainly describes the hardware of the MIL-S801XX switch. The switch is compact (10 inches) with eight 10/100BASE-TX UTP ports plus one 100BASE-FX fiber port. The physical dimensions of the MIL-S801XX switch are: 250mmx 132mmx 37mm (L 9.8”x W 5.2”x H 1.5”) Front Panel The Front Panel of the MIL-S801XX switch consists of eight 10/100 UTP switch ports (automatic MDI/MDIX), one 100BASE-FX fiber port and one DIPswitch to select fiber port for full-duplex or half-duplex mode.
MIL-S801XX switch with ST fiber port Figure 2-3. The Front Panel of the MIL-S801XX switch with ST fiber port MIL-S801XX switch with MT-RJ fiber port Figure 2-4. The Front Panel of the MIL-S801XX switch with MT-RJ fiber port MIL-S801XX switch with VF-45 fiber port Figure 2-5. The Front Panel of the MIL-S801XX switch with VF-45 fiber port RJ-45 Ports (Auto MDI/MDIX): Eight auto-sensing for 10BASE-T or 100BASE-TX connections.
LED Indicators The following table provides descriptions of the LED statuses and meaning. They provide a real-time indication of systematic operation status. LED Power Status On On Color Green Power On Green 100M LNK / ACT Green Off FDX / COL Blinks Off The port is successfully connecting with the device. The port is receiving or transmitting data. Blinks On The port is operating at the speed of 100 Mbps. In 10 Mbps mode or no device attached Off On Description No device attached.
Rear Panel The 3-pronged power plug is located at the Rear Panel of the 9-Port switch as shown in Figure 2-6. The switch will work with AC in the range 100-240V AC, 50-60Hz. Figure 2-6 The Rear Panel of the MIL-S801XX switch Desktop Installation Set the switch on a sufficiently large flat space with a power outlet nearby. The surface where you put your switch should be clean, smooth, level, and sturdy.
3.Network Application This section provides two samples of network topology in which the switch is used. In general, the MIL-S801XX switch is configured for use as a desktop or segment switch. The MIL-S801XX switch networks PCs, workstations, and servers to each other by connecting these devices directly to the switch. It automatically learns node address, which are subsequently used to filter and forward all traffic based on the destination address.
Segment Application Any of the RJ-45 ports on the MIL-S801XX switch can connect with other switches or Hubs to interconnect small workgroups to form larger switched networks. You can also use fiber ports to connect switches. The distance between two switches via fiber cable can be up to 2Km or up to 60Km (SC single-mode fiber connector). For enterprise networks where large data broadcast are constantly processed, this switch is suitable for a department connection to the corporate backbone.
4.Trouble Shooting This troubleshooting section is intended to help you solve the most common problems on the MIL-S801XX switch. The switch can be easily monitored through panel indicators to assist in identifying problems. This section describes common problems you may encounter and where you can find possible solutions. Diagnosing LED Indicator If the Link indicator does not light up after making a connection, you should check the network interface (e.g.
5.Technical Specifications This section provides the specifications for the MIL-S801XX switch Specifications Standards Compliance IEEE 802.3 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX/FX Fast Ethernet ANSI/IEEE 802.
A Division of Digi International
