User's Manual

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 19/05/14

SXTG-5HPacD

QuickSetupGuideandWarrantyInformation



TheSXTG-5HPacDcomesasacompleteset,andincludesabuiltin

802.11acdualchainwirelessdevice,andadualpolarization16dBi

sectorantenna.IthasoneGigabitEthernetconnectorwhichsupports

MDI-Xautodetection.

Firstuse

1. ConnectanEthernetcabletotheportbehind

thesmallplasticdoor

2. TheSXTaccepts24VPassivePoEfromthe

suppliedPoEinjector

3. ThedefaultIPaddressfromLANis192.168.88.1

forconfiguration

4. Usernameisadminandthereisnopassword

Powering

TheboardacceptspoweringfromtheEthernetport(PassivePoE)8-30VDC.Packagecontainsa24Vadapter.

Bootingprocess

RouterOSistheoperatingsystemofallRouterBOARDrouters.Pleaseseedetailedconfigurationguidehere:

http://wiki.mikrotik.com/wiki/Category:Manual

Thisdevicedoesn'tcomefittedwithaSerialPortconnector,soinitialconnectionhastobedoneviatheEthernet

cable,usingtheMikroTikWinboxutility.WinboxshouldbeusedtoconnecttothedefaultIPaddressof

192.168.88.1withtheusernameadminandnopassword.

IncaseIPconnectionisnotavailable,WinboxcanalsobeusedtoconnecttotheMACaddressofthedevice.More

informationhere:http://wiki.mikrotik.com/wiki/First_time_startup

Incaseyouwishtobootthedevicefromnetwork,forexampletouseMikroTikNetinstall,holdtheRESETbutton

ofthedevicewhenstartingituntiltheLEDlightturnsoff(behindthesmalldoor),andSXTwillstarttolookfor

Netinstallservers.

Mounting

Withtheclippointedforward,slidethemountingbracketintotherailonthebottomofthecase,untiltheclip

clicksintoplace.TheSXTcomesbundledwithahoseclamp-guidetheclampthroughtheopeninginthebracket

andaroundthepolewhereitwillbemounted.Tightenthehoseclampscrewwhenalignmentiscomplete.Two

screwholesareprovidedasadditionalsecurityagainstaccidentalbracketmovement.

TheSXTdevicehasaslidingdoor,behindwhichtheEthernetportandtheresetjumpersarelocated.Thisdoor

canbealsosecuredshutwithascrewintheprovidedscrewhole.

PAGE 1
SXTG-5HPacD Quick Setup Guide and Warranty Information The SXTG-5HPacD comes as a complete set, and includes a built in 802.11ac dual chain wireless device, and a dual polarization 16dBi sector antenna. It has one Gigabit Ethernet connector which supports MDI-X auto detection. First use 1. 2. 3. 4. Connect an Ethernet cable to the port behind the small plastic door The SXT accepts 24V Passive PoE from the supplied PoE injector The default IP address from LAN is 192.168.88.
PAGE 2
Buttons and Jumpers • • RouterOS reset jumper hole (access through the plastic door) – resets RouterOS software to defaults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place until RouterOS configuration is cleared.
PAGE 3
Federal Communication Commission Interference Statement (FCC ID: TV7SXTG-5HACD) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.