User's Manual

ManualsBrandsMikrotikls ManualsElectronicsMIMO BROADBAND DIGITAL TRANSMISSION SYSTEM

See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 16-Oct-2012

RouterBOARD+SXT+5nD+r2+

Quick&Setup&Guide&and&Warranty&Information&

The$RouterBOARD$SXT$5nD$r2$comes$as$a$com plete$set,$and$inclu d e s$a $

built$in$802.11n$dual$chain$wireless$device,$and$a$dual$polarization$

16dBi$antenna.$It$has$one$BASEGT$10/100$ethernet$connector$which$

supports$MDIGX$auto$detection.$

First&use&

1. Connect$an$Ethernet$cable$to$the$port$behind$the$small$plastic$door$

2. The$SXT$accepts$24V$Passive$PoE$from$a$PoE$injector$

3. The$default$IP$address$from$LAN$is$192.168.88.1$for$configuration$

4. Username$is$admin$and$there$is$no$password$

Powering&

The$board$accepts$powering$from$the$Ethernet$port$(Passive$PoE)$8G30V$DC.$Package$contains$a$24V$adapter.$

Maximum$power$consumption$of$the$device$is$7W.$

Booting&process&

Initial$con n e c tio n $h a s$t o $b e $d o n e$v ia $th e $E th e rn e t$c a b le. $O p e n $192.168.88.1+in$your$web $b ro w s e r,$an d $c ho o s e$

“Webfig”$for$browser$based$configuration$or$“Winbox”$for$a$Windows$utility$with$the$same$functions.+Username$

is$admin$and$there$is$no$password.$In$case$IP$connection$is$not$available,$Winbox$can$be$used$to$connect$to$the$

MAC$address$of$the$device.$More$information$here:$http://wiki.mikrotik.com/wiki/First_time_startup$

In$case$you$wis h $to$boot$the$device$from$network,$for$example$to$use$MikroTik$Netinstall,$hold$the$RESET$button$

of$the$device$when$starting$it$until$the$LED$light$turns$off,$and$Metal$will$start$to$look$for$Netinstall$servers.$

Mounting&

With$the$clip$pointed$forward,$slide$the$mounting$bracket$into$the$rail$on$the$bottom$of$the$case,$until$the$clip$

clicks$into$place.$The$SXT$comes$bundled$with$a$hose$clamp$G$guide$the$clamp$through$the$opening$in$the$bracket$

and$around$the$pole$where$it$will$be$mounted.$Tighten$the$hose$clamp$screw$when$alignment$is$comp lete.$Two$

screw$holes$are$provided$as$additional$security$against$accidental$bracket$moveme nt.$

The$SXT$device$has$a$sliding$door,$behind$which$the$Ethernet$port,$and$the$reset$jumpers$are$located.$This$door$

can$be$also$secured$shut$with$a$screw$in$the$provided$screw$hole.&

$ &

Summary of content (3 pages)

PAGE 1
RouterBOARD SXT 5nD r2 Quick Setup Guide and Warranty Information The RouterBOARD SXT 5nD r2 comes as a complete set, and includes a built in 802.11n dual chain wireless device, and a dual polarization 16dBi antenna. It has one BASE-‐T 10/100 ethernet connector which supports MDI-‐X auto detection. First use 1. 2. 3. 4.
PAGE 2
Buttons and Jumpers • • RouterOS reset jumper hole (access through the plastic door) – resets RouterOS software to defaults. Must short cir-‐ cuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold screwdriver in place until RouterOS configuration is cleared.
PAGE 3
Federal Communication Commission Interference Statement (FCC ID: TV7SXT-5ND) This equipment has been tested and found to comply with the limits for a Class B digital device, pur-‐ suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.