User Manual

ManualsBrandsMikroTik ManualsComputers & AccessorieswAP R

Table Of Contents

wAP R

wAP R

Quickstart

Use a Phillips head screwdriver to loosen the screw, which secures the bottom lid.

Install your modem (optional).

Choose your powering solution, please see the section for possibilities.wAP R#Powering

Plug the included PoE injector into the ISP outlet and attach an Ethernet cable to it. Connect the other end of the Ethernet cable to this MikroTik

router. Plug the provided power supply into the PoE injector.

Wireless AP mode is enabled by default, you can connect from your computer to the SSID that begins with "MikroTik". The configuration interface

is available via a web browser. The address is .https://192.168.88.1

Once connected to the wireless network, open in your web browser to start the configuration.https://192.168.88.1

User name: a and there is no password by default you will be logged in automatically to the Quick Set screen.

dmin

We recommend clicking the "Check for updates" button on the right side and updating your RouterOS software to the latest version to ensure the

best performance and stability.

To personalize your wireless network, SSID can be changed in the fields "Network Name";

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings.

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols.

Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next

time.

Click on the "Apply Configuration" to save changes.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.

Summary of content (10 pages)

PAGE 1
wAP R wAP R Quickstart Use a Phillips head screwdriver to loosen the screw, which secures the bottom lid. Install your modem (optional). Choose your powering solution, please see the wAP R#Powering section for possibilities. Plug the included PoE injector into the ISP outlet and attach an Ethernet cable to it. Connect the other end of the Ethernet cable to this MikroTik router. Plug the provided power supply into the PoE injector.
PAGE 2
1. 2. 3. 4. 5. 6. Scan QR code and choose your preferred OS. Install and open application. By default, the IP address and user name will be already entered. Click Connect to establish a connection to your device through a wireless network. Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps. An advanced menu is available to fully configure all necessary settings.
PAGE 3
It's recommended to secure Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm. Mounting unit on the wall: 1. Use included a template to mark spots for drilling holes. And if needed for Ethernet cable. Align accordingly, it will depend on how the device will be mounted finally. 2. Insert dowels if needed, depends on wall structure and material. 3. Place included a steel bracket on the wall. 4. Use screws to secure it in the place. 5.
PAGE 4
Avoid mounting the device on the low ground spot, as you won't be able to attach and close the bottom latch. Mounting on the ceiling: A Special bracket is included in the package to mount on the drop ceiling. As it consists of two parts, to be attached on both sides of the ceiling tile. 1. Use the template to mark spots for holes. 2. Place both mounting brackets on the spot. 3. Secure them together using screws. Continue assembling in the same manner if mounting on the wall. 1. 2. 3. 4.
PAGE 5
Pull the cover in the opposite direction from the device to remove it. Reassemble. Powering The device accepts power from the power jack or from the Ethernet port: Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 9-30 V DC; Ethernet port accepts 802.3af/at PoE 9-30 V DC. The power consumption under maximum load can reach 6 W. Please attach ground (earth) wire to the screw under the bottom lid. Connecting to a PoE Adapter: 1.
PAGE 6
Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery. Operating system support The device supports RouterOS software version 6.
PAGE 7
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
PAGE 8
EL Με την παρούσα ο/η Mikrotīkls SIA , δηλώνει ότι ο ραδιοεξοπλισμός RouterBOARD πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: https://mikrotik.com/products EN Hereby, Mikrotīkls SIA declares that the radio equipment type RouterBOARD is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.
PAGE 9
NO Mikrotīkls SIA erklærer herved at utstyret RouterBOARD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse: https://mikrotik.com/products PL Mikrotīkls SIA niniejszym oświadcza, że typ urządzenia radiowego RouterBOARD jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: https://mikrotik.
PAGE 10
DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im {+}https://mt.lv/help-de+ EL. εγχειρίδιο οδηγιών: Συνδέστε τον προσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για να διαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο {+}https://mt.lv/help-el+ EN.