User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesLHG 2

Table Of Contents

LHG-series

LHG-series

This manual covers LHG models:

LHG 2 (RBLHG-2nD)

LHG 5 (RBLHG-5nD)

LHG HP5 (RBLHG-5HPnD)

LHG 5 ac (RBLHGG-5acD)

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be mounted on a pole. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct

hardware or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Read the installation instructions before connecting the system to the power source.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

The LHG is an outdoor wireless router with a built-in directional antenna. It can be used as a CPE or for point-to-point links (use RouterOS wireless mode

"bridge" to work as a single-client AP for point-to-point scenarios).

Connecting

Open the Ethernet door to connect an Ethernet cable to the Ethernet port, connect the other end of the Ethernet cable to the included PoE injector.

Plug the PoE injector into your network switch or computer.

Plug the included power supply into the PoE injector to start up the device.

Download WinBox configuration tool ;https://mt.lv/winbox

Default IP: 192.168.88.1, user name: and there is no password, or use

admin

Neighborstab and connect through MAC address;

Once connected configure the device, so it has an active Internet connection ;https://mt.lv/configuration

Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade

Connect again and in the QuickSet menu choose your country, to apply country regulation settings;

Set up your router password in the bottom field to the right and repeat it, it will be used to log in next time.

The device is preconfigured as a wireless client and all you need to do is select the AP to connect to and set a device password. You can do this in the

QuickSet tab that is opened by default.

In case the IP connection is not available, Winbox can be used to connect to the MAC address of the device. In case you wish to boot the device from the

network, for example, to use MikroTik Netinstall, hold the RESET button of the device when starting it, until the LED light turns off, then the device will start

to look for Netinstall servers. More information about using RouterOS and connecting to this device in our documentation: https://mt.lv/help

Assembly and Mounting

Summary of content (8 pages)

PAGE 1
LHG-series This manual covers LHG models: LHG 2 (RBLHG-2nD) LHG 5 (RBLHG-5nD) LHG HP5 (RBLHG-5HPnD) LHG 5 ac (RBLHGG-5acD) Safety Warnings Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Ultimate disposal of this product should be handled according to all national laws and regulations. The Installation of the equipment must comply with local and national electrical codes.
PAGE 2
1. Attach the two legs to the LHG case. 2. Snap the assembled LHG unit to the grid in the appropriate locations. 3. Fix the legs in place with two self-thread screws (Use Phillips screwdriver PH2). The device is designed to be mounted on the pole using zip ties or steel clamps as shown in the picture. The clamping diameter with provided steel clamps is 35 – 70 mm.
PAGE 3
1. Guide provided steel clamps through the unit. 2. Attach the device to the pole. 3. Align and tighten the clamps to secure the device. Optional: If required, before mounting the unit, you can insert the included 5-degree adjustment adapter into the top or bottom slot where the mounting ring is inserted. This will create an additional upward or downward angle when the unit is tightened to a vertical pole.
PAGE 4
Additional mounting brackets can be purchased separately: LHG mount solidMOUNT Powering The device accepts powering only from Passive PoE injectors. Connecting to a POE Adapter: 1. Connect the Ethernet cable from the device to the POE port of the POE adapter. 2. Connect an Ethernet cable from your LAN to the LAN port of the POE adapter, please mind arrows for data and power flow. 3. Connect the power cord to the adapter, and then plug the power cord into a power outlet.
PAGE 5
Reset button The reset button has three functions: Hold this button during boot time until the LED light starts flashing, release the button to reset the RouterOS configuration (total 5 seconds). Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds). Or keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds).
PAGE 6
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
PAGE 7
CE Declaration of Conformity BG С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение RouterBOARD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://mikrotik.com/products CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení RouterBOARD je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: https://mikrotik.
PAGE 8
SK Mikrotīkls SIA týmto vyhlasuje, že rádiové zariadenie typu RouterBOARD je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: https://mikrotik.com/products SL Mikrotīkls SIA potrjuje, da je tip radijske opreme RouterBOARD skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: https://mikrotik.