User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesQRT 5 ac

Table Of Contents

QRT 5 ac

QRT 5 ac

Quickstart

Please follow these quick steps to set up your device:

Mount unit in your desired place, please see paragraph.QRT 5 ac#Mounting

Slide off latch to access Ethernet port. Please see section.QRT 5 ac#Opening latch

Connect your PoE cable to the Ethernet port, please see section.QRT 5 ac#Powering

Set your computer IP configuration to automatic (DHCP).

From your PC connect to the wireless network name which starts with "MikroTik".

Once connected to the wireless network, open in your web browser to start the configuration.https://192.168.88.1

User name: a and there is no password by default you will be logged in automatically to the Quick Set screen.

dmin

We recommend clicking the "Check for updates" button on the right side and updating your RouterOS software to the latest version to ensure the

best performance and stability.

To personalize your wireless network, SSID can be changed in the fields "Network Name".

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings.

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols.

Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next

time.

Click on the "Apply Configuration" to save changes.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for

preventing accidents.

Read the installation instructions before connecting the system to the power source.

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for obtaining

any required local or national safety inspections of the structural integrity of the installation by the local authority/inspection department.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to

use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to people and damage to the

system.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate

at your own risk.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.

Scan QR code and choose your preferred OS.

This device needs to be upgraded to RouterOS v6.46 or the latest version to ensure compliance with local

authority regulations.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Note. The information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of

this

document.

Summary of content (10 pages)

PAGE 1
QRT 5 ac This device needs to be upgraded to RouterOS v6.46 or the latest version to ensure compliance with local authority regulations. It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed. Note. The information contained here is subject to change. Please visit the product page on www.
PAGE 2
. 3. 4. 5. 6. Install and open application. By default, the IP address and user name will be already entered. Click Connect to establish a connection to your device through a wireless network. Choose Quick setup and application will guide you through all basic configuration settings in a couple of easy steps. An advanced menu is available to fully configure all necessary settings. Powering The device accepts power from the PoE to the Ethernet port: Passive Power over Ethernet 8-30 V DC .
PAGE 3
Front status LED behavior RouterOS allows configuring each LED's activity the way that the user wishes. It is possible to configure the LEDs to display wireless strength, blink the LEDs on interface traffic activity and many other options. For further information please visit https://wiki.mikrotik.com/wiki/Manual:System/LEDS Default factory configuration for this device: 1. 2. 3. 4. Solid Blue – The device is powered on. Solid Green – Connected Ethernet port. Solid Green – User-defined LED.
PAGE 4
Attach the two brackets (A) to the swivel adjuster (B), by using the four provided screws (use a PH1 screwdriver). Place the two U-bolts (C) around the mast or pole, and guide them through the holes on the swivel adjuster (D). Then, tighten the U-bolts, each with one regular washer, one spring washer, and one nut, as shown in the image to the right. All nuts need to be tightened using a size 10 (3/8 in) wrench. Maximum diameter of the pole can be up to 70 mm.
PAGE 5
Use the mounting bracket (E), and put it on to the back of the antenna. Install with one rubber ring, one washer, and one nut for each of the builtin bolts (in that order). Attach the swivel adjuster to the mounting bracket. Use the long bolt in the position (F). Put one regular washer, and one spring washer onto the shorter screws, then put them in positions (G). Do not tighten too much, as you need to adjust the antenna now.
PAGE 6
Grounding The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded. The device includes a grounding wire attachment screw on the backside of the unit.
PAGE 7
IE IT LV LT LU MT NL PL PT RO SE SI SK UK BFWA (Broadband Fixed Wireless Access) members noted in bold. Federal Communication Commission Interference Statement FCC ID:TV7RB922-5HPACTM This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 8
https://mikrotik.com/products DA Hermed erklærer Mikrotīkls SIA , at radioudstyrstypen RouterBOARD er i overensstemmelse med direktiv 2014/53/EU. EUoverensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: https://mikrotik.com/products DE Hiermit erklärt Mikrotīkls SIA , dass der Funkanlagentyp RouterBOARD der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EUKonformitätserklärung ist unter der folgenden Internetadresse verfügbar: https://mikrotik.
PAGE 9
https://mikrotik.com/products MT B'dan, Mikrotīkls SIA , niddikjara li dan it-tip ta' tagħmir tar-radju RouterBOARD huwa konformi mad-Direttiva 2014/53/UE. It-test kollu taddikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: https://mikrotik.com/products NL Hierbij verklaar ik, Mikrotīkls SIA , dat het type radioapparatuur RouterBOARD conform is met Richtlijn 2014/53/EU.
PAGE 10
document. BG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.88.1 в уеб браузър, за да настроите продукта. Повече информация в {+}https://mt.lv/help-bg+ CS. Návod k použití: Připojte napájecí adaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete v {+}https://mt.lv/help-cs+ DA. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.