User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesIntercell 10 B38+B39

Table Of Contents

Intercell

Intercell

Intercell 10 B38+B39

The intercell 10 B38+B39 is an outdoor TDD-LTE dual carriers base station with 2*(2*10W) output power (each carrier supports 2x2 MIMO with 10W

output each RF channel).

Quickstart

Please follow these quick steps to set up your device:

Connect external antennas and Ethernet cable to the connectors (see " ");Expansion ports and slots

Connect the device to the power source (see " ");Powering

Connect with your laptop to the Ethernet port for configuration.

The device can get the IP address by DHCP and Static assignment;

Once connected, default maintenance IP address: 192.168.200.200, user name: admin, password: MikroTik;

If connecting with the Static assignment method, configure the IP address of your laptop as 192.168.200.100/24, then connect through https to

the device: 192.168.200.200;

Configure backhaul and radio network see " ".Configuration

Powering

The device accepts power in the following way:

Input power jack accepts 48 V DC. The only connector with cable is provided with the package, you will need the power unit - generating 48 V.

The power consumption under maximum load can reach 200 W.

Connect provided cable to your power source.

Connect cable connector to the device.

If using Ethernet cable add RBGESP to the setup, which comes with the package.

Configuration

All configuration is necessary to carry out through the webGUI.

The configuration of this device should be done by a qualified person.

Summary of content (14 pages)

PAGE 1
Intercell Intercell 10 B38+B39 The intercell 10 B38+B39 is an outdoor TDD-LTE dual carriers base station with 2*(2*10W) output power (each carrier supports 2x2 MIMO with 10W output each RF channel). Quickstart Please follow these quick steps to set up your device: Connect external antennas and Ethernet cable to the connectors (see "Expansion ports and slots"); Connect the device to the power source (see "Powering"); Connect with your laptop to the Ethernet port for configuration.
PAGE 2
This topology shows typical Smallcell network architecture. HeNB works as LTE the base station provides LTE service to UE； NMS: HeNB management system (HeMS) is a virtualized solution that provides a full lifecycle of small cell management functions. It supports TR-181 and TR-196 data model which are defined by Broadband. HeNB-GW: HeNB Gateway is deployed between HeNB and MME, provide the aggregation of control and user plane traffic and capabilities necessary to manage large clusters of small cells.
PAGE 3
4. Press "Submit", HeNB will reboot to take configuration into effect. 5. Connect the HeNB WAN interface back to LAN. Login: Login WebGUI with HTTPS. Backhaul parameter Configure the NME/HeNB-GW IP address: Path: Management > Cell > S1SigLinkServer.
PAGE 4
Radio network parameter Output power calculation table Please see the formula and table on how to determine output power： Output power of each antenna = ReferenceSignalPower + Base（dBm） Output power of 2 antennas = ReferenceSignalPower + Base + 3（dBm） Band Width Base 1MHz 19 3MHz 23 5MHz 25 10MHz 28 15MHz 30 20MHz 31 Warning! The maximum Tx power is 40 dBm, please calculate the Tx power accordingly otherwise the power amplifier might be damaged! Configure common radio parameters: Path: Manage
PAGE 5
Configure Cell 1 radio parameters: CellIdentity: 257 CandidateARFCNList: 38400 Note: EARFCN in Downlink, the Uplink EARFCN will be configured automatically by HeNB. CandidatePCIList: 0..503 Note: Range from 0 to 503, HeNB will select PCI automatically. FreqBandIndicator: 39 DL Bandwidth: 100 Note: 20MHz ↔ 100, 15 MHz ↔ 75, 10MHz ↔ 50, 5MHz ↔ 25. UL Bandwidth: equal to DL Bandwidth value.
PAGE 6
Configure Cell 2 radio parameters: CellIdentity: 258 CandidateARFCNList: 37900 Note: EARFCN in Downlink, Uplink EARFCN will be configured automatically by HeNB. CandidatePCIList: 0..503 Note: Range from 0 to 503, HeNB will select PCI automatically. FreqBandIndicator: 38 DL Bandwidth: 100 Note: 20MHz ↔ 100, 15 MHz ↔ 75, 10MHz ↔ 50, 5MHz ↔ 25. UL Bandwidth: equal to DL Bandwidth value.
PAGE 7
Select the "AdminState" when all the above parameters are well configured. Note: This is the switch to control the RF function, select enable RF function when all parameters are well configured. Press "Submit", then HeNB will reboot to take configuration into effect. Checking the RF status: Path: Management > Cell > Cell1 > OpState, Management > Cell > Cell1 > OpState; Note: "True" means the radio cell was established successfully.
PAGE 8
Mounting The device is designed to be used outdoors. When mounting on the wall or mast, please ensure that the cable feed is pointing downwards. The IPX rating scale of this device is IP66. We recommend using Cat6 shielded cables. Mounting and configuration of this device should be done by a qualified person. The package includes mounting parts for pole or wall mounting. Acceptable pole diameter 50 – 120 mm.
PAGE 9
2. Get the pole mounting accessories from the packing case, including 4 fixed plates, 4 M12 bolts, 4 M12 nuts. Guide the M12 bolt through the mounting frame, the fixing plate, cradle, and fix it on the cradle as shown in the picture. 3. Keep the 4 fixing screws near the lower side of the chassis fixed on the chassis and leave a 3mm gap for hanging the mounting frame. 4. Aim the case on the wall mount, let screws on the 2 sides of the chassis fall into the mounting frame fixing holes.
PAGE 10
Grounding The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded. Attach your grounding wire to the grounding screw, then attach the other end of the grounding wire to the grounded mast. Power interface lightning protection – GB/T 17626.5, IEC61000-4-5. Expansion slots and ports 1. 2. 3. 4. 5. 6. 7. 8. Power supply connector. Antenna connectors. LED indicating power. LED indicating activity. GPS antenna connector. SNIFF antenna connector.
PAGE 11
6 RF(4*ANT, SNF, GPS/BD). Max output power 40 ± 1dBm / antenna. All IP based backhaul, many IP backhauls methods can be used, including RJ45 Ethernet, SFP. Frequency Bands B38:2570MHz-2620MHz, B39:1880MHz-1920MHz, channel bandwidth 5/10/15/20 MHz. Accessories The package includes the following accessories that come with the device: Power cable with a plug (PSU not included); SFP – S-31DLC20D, https://mikrotik.com/product/S-31DLC20D-181 Ethernet cable navigation plug, RBGESP - https://mikrotik.
PAGE 12
Reset configuration via serial console CFG Import for Intercell Intercell monitoring Intercell dual-carrier TDD enterprise small cell configuration guide
PAGE 13
Operating system support The device supports Intercell HeNB software. RouterOS are not supported. Safety Notice Electric shock hazard. This equipment is to be serviced by trained personnel only. CE Declaration of Conformity BG С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение Intercell 10 B38+B39 е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://mikrotik.
PAGE 14
Il fabbricante, Mikrotīkls SIA, dichiara che il tipo di apparecchiatura radio Intercell 10 B38+B39 è conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: https://mikrotik.com/products IS Hér með lýsir Mikrotīkls SIA því yfir að Intercell 10 B38+B39 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB samræmisyfirlýsingar er að finna á eftirfarandi veffangi: https://mikrotik.