User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesCSS610-8G-2S+IN

Table Of Contents

CSS610-8G-2S+IN

CSS610-8G-2S+IN

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Read the installation instructions before connecting the system to the power source.

Quick start

Download the latest SwitchOS software version fromhttps://mikrotik.com/download;

Connect your computer to any of the ethernet ports;

Connect the device to the power source;

Set an IP address of your computer to 192.168.88.3;

Open your Web browser, the default management IP address is 192.168.88.1 / 192.168.88.2, with the username and no password;

admin



Upload file with the web browser to the Upgrade tab, the device will reboot after an upgrade;

Set up your password to secure the device.

Powering

The device accepts power from the power jack or from the first Ethernet port (Passive PoE).

Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 12-57V DC.

The first Ethernet port accepts passive PoE input 12-57V DC.

Power consumption 5 W, with attachments 11 W.

Connecting to a PoE Adapter:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.

Connect an Ethernet cable from your local network (LAN) to the PoE adapter.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Configuration

SwOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to the

possibilities:https://mt.lv/help.

For recovery purposes, it is possible to boot the device for reinstallation, see sectionButtons and Jumpers.

First-time configuration https://wiki.mikrotik.com/wiki/SwOS/CSS610;

The device upgrade ;https://mt.lv/upgrade

Extension slots and ports

Summary of content (4 pages)

PAGE 1
CSS610-8G-2S+IN CSS610-8G-2S+IN Safety Warnings Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. Ultimate disposal of this product should be handled according to all national laws and regulations. The Installation of the equipment must comply with local and national electrical codes.
PAGE 2
Eight individual Gigabit Ethernet ports, supporting automatic cross/straight cable connection (Auto MDI/X), so you can use either straight or crossover cables for connecting to other network devices; 2 SFP+ ports for using 10G SFP+; Specifications Please visit wiki pages for the MikroTik SFP module compatibility table: https://wiki.mikrotik.
PAGE 3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.
PAGE 4
LV Ar šo Mikrotīkls SIA deklarē, ka radioiekārta CSS610-8G-2S+IN atbilst Direktīvai 2014/30/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: https://mikrotik.com/products MT B'dan, Mikrotīkls SIA , niddikjara li dan it-tip ta' tagħmir tar-radju CSS610-8G-2S+IN huwa konformi mad-Direttiva 2014/30/UE. It-test kollu taddikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: https://mikrotik.