Quick Guide

ManualsBrandsMikroTik ManualsComputers & AccessoriesCRS326-24G-2S+IN

Table Of Contents

CRS326-24G-2S+IN

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be

familiar with standard practices for preventing accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

Failure to use the correct hardware or to follow the correct procedures could result in a hazardous

situation to people and damage to the system.

Read the installation instructions before connecting the system to the power source.

Quick start

• Connect two powering units to the AC source using power cords.

• The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

• Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username admin

and no password. If IP is no available choose the Neighbors tab and connect to the device using the MAC

address.

• We recommend clicking the “Check for updates” button and updating your RouterOS software to the latest

version to ensure the best performance and stability. The device needs to have an active internet

connection.

• To upgrade manually go to our download page https://mikrotik.com/download

• Choose packaged based on your device model.

• Download to your PC.

• Upload packages to Files menu in WinBox and reboot the device.

• Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be placed on the desktop.

The device has no protection from water contamination, please ensure the placement of the device in a dry and

ventilated environment.

We recommend Cat6 cables for our devices.

Mounting and configuration of this device should be done by a qualified person.

Extension slots and ports

• 24 of Gigabit Ethernet ports.

• Two 10G SFP+ ports.

• 1x RJ45 console port (set at 115200bits/s, 8 data bits, 1 stop bit no parity).

Please visit wiki pages for MikroTik SFP module compatibility and configuration table:

https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table

See mikrotik.com/products for the latest version of this document. Document #54530 Modified on: 10.MAR.2020

Summary of content (5 pages)

PAGE 1
CRS326-24G-2S+IN Safety Warnings Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Ultimate disposal of this product should be handled according to all national laws and regulations. The Installation of the equipment must comply with local and national electrical codes.
PAGE 2
Powering The device accepts power in the following ways: • • Ethernet port accepts passive PoE 10-30 V DC ⎓. Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 10-30 V DC⎓. The power consumption under maximum load can reach 24 W. Connecting to a PoE Adapter: 1. Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter; 2. Connect an Ethernet cable from your local network (LAN) to the PoE adapter; 3.
PAGE 3
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
CE Declaration of Conformity Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039. BG С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение RouterBOARD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://mikrotik.com/products CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení RouterBOARD je v souladu se směrnicí 2014/53/EU.
PAGE 5
BG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.88.1 в уеб браузър, за да настроите продукта. Повече информация в http://mt.lv/help-bg CS. Návod k použití: Připojte napájecí adaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete v http://mt.lv/help-cs DA. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.1 i en webbrowser til at konfigurere produktet.