User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesnetPower 16P

Table Of Contents

netPower 16P

netPower 16P

netPower 16P (CRS318-16P-2S+OUT)

The netPower is a weatherproof switch with the capability of delivering PoE to your connected devices.

Quickstart

Please follow these quick steps to set up your device:

Open the bottom lid (see " ");netPower 16P#Bottom Lid

Connect all served devices to Ethernet ports;

Connect the device to the power source (see " ");netPower 16P#Powering

Once connected to the same network, open in your web browser to start configuration, user name: a and there is no https://192.168.88.1

dmin

password by default;

Once connected configure the device, so it has an active Internet connection ;https://mt.lv/configuration

Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade

Set up your router password in the bottom field of the QuickSet menu, to the right and repeat it, it will be used to login next time.

Expansion slots and ports

DC power connector 48 – 57 V.

DC power connector 18 – 30 V.

LED indicating a power state of the device.

Reset button.

Gigabit Ethernet, 8 - ports, delivering PoE out.

Two - 10G SFP+ ports.

LED Indicating the activity of SFP port.

LED Indicating the speed of SFP port.

Configuration

Summary of content (10 pages)

PAGE 1
netPower 16P netPower 16P (CRS318-16P-2S+OUT) The netPower is a weatherproof switch with the capability of delivering PoE to your connected devices. Quickstart Please follow these quick steps to set up your device: Open the bottom lid (see "netPower 16P#Bottom Lid"); Connect all served devices to Ethernet ports; Connect the device to the power source (see "netPower 16P#Powering"); Once connected to the same network, open https://192.168.88.
PAGE 2
The device can be discovered using Winbox utility, by clicking on the Neighbors list. The default management address is 192.168.88.1. To reach both devices needs to be in the same IP network. Configured as a bridge, ARP, and fast forward enabled. RSTP protocol activated. RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to the possibilities: https://mt.lv/help.
PAGE 3
2. Pull the cover towards. 3. Lift to access Ethernet ports. Mounting The device can be mounted in several ways: pole, wall, or ceiling. The package also includes a drill hole template with detailed mounting instructions, to help you with the drill hole marking. The device has eight mounting points for versatility use zip ties or steel clamps for mounting on the pole. The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards.
PAGE 4
Mounting points: There are eight mounting points on the back of this device. Choose the most relevant ones. Middle points are designed for mounting on the mast, there are curves on the case for slim fitment. It's recommended to secure Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm. The device must be mounted by UP arrow facing upwards. The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded.
PAGE 5
1. 2. 3. 4. 5. Insert provided steel clamps into mounting spots. Attach the unit to the mast. Align the device and secure it by tightening steel clamps with a PH2 screwdriver. Guide Ethernet cables through the opening and connect to the Ethernet ports. Close bottom latch and secure with a screw. A – Always make sure to place the unit in an upwards position. B - It's recommended to use electrical tape to increase friction between materials.
PAGE 6
1. Use included a template to mark spots for drilling holes. Align accordingly, it will depend on how the device will be mounted finally. 2. 3. 4. 5. Insert dowels if needed, depends on wall structure and material. Insert screws and screw them by leaving approximately 1 cm out. Attach the unit to the position. Use screw holes under the bottom cover and tighten to secure in place. Extend your Ethernet cables through the openings and connect to Ethernet ports. 6. Close bottom latch.
PAGE 7
The device supports RouterOS software version 6.45.3. The specific factory-installed version number is indicated in the RouterOS menu /system resource. Other operating systems have not been tested. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 8
https://mikrotik.com/products EN Hereby, Mikrotīkls SIA declares that the radio equipment type RouterBOARD is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.com/products ES Por la presente, Mikrotīkls SIA declara que el tipo de equipo radioeléctrico RouterBOARD es conforme con la Directiva 2014/53/UE.
PAGE 9
https://mikrotik.com/products PL Mikrotīkls SIA niniejszym oświadcza, że typ urządzenia radiowego RouterBOARD jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: https://mikrotik.com/products PT O(a) abaixo assinado(a) Mikrotīkls SIA declara que o presente tipo de equipamento de rádio RouterBOARD está em conformidade com a Diretiva 2014/53/UE.
PAGE 10
s://mt.lv/help-no+ LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterį įjunkite įrenginį. Į interneto naršyklę 192.168.88.1 Atidarykite galite konfigūruoti gaminį. Daugiau informacijos rasite {+}https://mt.lv/help-lt+ LV. Lietošanas instrukcija: Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu. Plašāka informācija {+}https://mt.lv/help-lv+ MT. Manwal tal-istruzzjoni: Qabbad l-adapter tal-qawwa biex iddawwar it-tagħmir. Iftaħ 192.