Datasheet

PIC18F87J50 FAMILY
DS39775C-page 346 © 2009 Microchip Technology Inc.
24.1 Configuring the Comparator
Voltage Reference
The comparator voltage reference module is controlled
through the CVRCON register (Register 24-1). The
comparator voltage reference provides two ranges of
output voltage, each with 16 distinct levels. The range
to be used is selected by the CVRR bit (CVRCON<5>).
The primary difference between the ranges is the size
of the steps selected by the CV
REF Selection bits
(CVR3:CVR0), with one range offering finer resolution.
The equations used to calculate the output of the
comparator voltage reference are as follows:
If CVRR =
1:
CV
REF = ((CVR3:CVR0)/24) x (CVRSRC)
If CVRR =
0:
CV
REF =(CVRSRC/4) + ((CVR3:CVR0)/32) x
(CV
RSRC)
The comparator reference supply voltage can come
from either V
DD and VSS, or the external VREF+ and
V
REF- that are multiplexed with RA2 and RA3. The
voltage source is selected by the CVRSS bit
(CVRCON<4>).
The settling time of the comparator voltage reference
must be considered when changing the CV
REF
output (see Table 28-3 in Section 28.0 “Electrical
Characteristics”).
The CVRCON register is a shared address SFR and
uses the same address as the PR4 register. The
CVRCON register is accessed by setting the ADSHR
bit (WDTCON<4>).
REGISTER 24-1: CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
CVREN CVROE
(1)
CVRR CVRSS CVR3 CVR2 CVR1 CVR0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7 CVREN: Comparator Voltage Reference Enable bit
1 =CVREF circuit powered on
0 =CV
REF circuit powered down
bit 6 CVROE: Comparator VREF Output Enable bit
(1)
1 =CVREF voltage level is also output on the RF5/AN10/C1INB/CVREF pin
0 =CV
REF voltage is disconnected from the RF5/AN10/C1INB/CVREF pin
bit 5 CVRR: Comparator V
REF Range Selection bit
1 = 0 to 0.667 CVRSRC, with CVRSRC/24 step size (low range)
0 = 0.25 CV
RSRC to 0.75 CVRSRC, with CVRSRC/32 step size (high range)
bit 4 CVRSS: Comparator V
REF Source Selection bit
1 = Comparator reference source, CV
RSRC = (VREF+) – (VREF-)
0 = Comparator reference source, CV
RSRC = AVDD – AVSS
bit 3-0 CVR3:CVR0: Comparator VREF Value Selection bits (0 ≤ (CVR3:CVR0) ≤ 15)
When CVRR =
1:
CV
REF = ((CVR3:CVR0)/24) • (CVRSRC)
When CVRR =
0:
CV
REF = (CVRSRC/4) + ((CVR3:CVR0)/32) • (CVRSRC)
Note 1: CVROE overrides the TRISF<5> bit setting.