Datasheet

© 2009 Microchip Technology Inc. DS39775C-page 229
PIC18F87J50 FAMILY
18.4.7.1 Auto-Shutdown and Automatic
Restart
The auto-shutdown feature can be configured to allow
automatic restarts of the module following a shutdown
event. This is enabled by setting the P1RSEN bit of the
ECCP1DEL register (ECCP1DEL<7>).
In Shutdown mode with P1RSEN = 1 (Figure 18-10),
the ECCP1ASE bit will remain set for as long as the
cause of the shutdown continues. When the shutdown
condition clears, the ECCP1ASE bit is cleared. If
P1RSEN = 0 (Figure 18-11), once a shutdown condi-
tion occurs, the ECCP1ASE bit will remain set until it is
cleared by firmware. Once ECCP1ASE is cleared, the
Enhanced PWM will resume at the beginning of the
next PWM period.
Independent of the P1RSEN bit setting, if the
auto-shutdown source is one of the comparators, the
shutdown condition is a level. The ECCP1ASE bit
cannot be cleared as long as the cause of the shutdown
persists.
The Auto-Shutdown mode can be forced by writing a ‘1’
to the ECCP1ASE bit.
18.4.8 START-UP CONSIDERATIONS
When the ECCP1 module is used in the PWM mode,
the application hardware must use the proper external
pull-up and/or pull-down resistors on the PWM output
pins. When the microcontroller is released from Reset,
all of the I/O pins are in the high-impedance state. The
external circuits must keep the power switch devices in
the OFF state until the microcontroller drives the I/O
pins with the proper signal levels, or activates the PWM
output(s).
REGISTER 18-3: ECCPxAS: ECCPx AUTO-SHUTDOWN CONTROL REGISTER
R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
ECCPxASE ECCPxAS2 ECCPxAS1 ECCPxAS0 PSSxAC1 PSSxAC0 PSSxBD1 PSSxBD0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7 ECCPxASE: ECCPx Auto-Shutdown Event Status bit
0 = ECCPx outputs are operating
1 = A shutdown event has occurred; ECCPx outputs are in shutdown state
bit 6-4 ECCPxAS2:ECCPxAS0: ECCPx Auto-Shutdown Source Select bits
000 = Auto-shutdown is disabled
001 = Comparator 1 output
010 = Comparator 2 output
011 = Either Comparator 1 or 2
100 =FLT0
101 = FLT0 or Comparator 1
110 = FLT0 or Comparator 2
111 = FLT0 or Comparator 1 or Comparator 2
bit 3-2 PSSxAC1:PSSxAC0: Pins A and C Shutdown State Control bits
00 = Drive Pins A and C to ‘0’
01 = Drive Pins A and C to ‘1’
1x = Pins A and C tri-state
bit 1-0 PSSxBD1:PSSxBD0: Pins B and D Shutdown State Control bits
00 = Drive Pins B and D to ‘0’
01 = Drive Pins B and D to ‘1’
1x = Pins B and D tri-state
Note: Writing to the ECCP1ASE bit is disabled
while a shutdown condition is active.