User Manual

AN
RST
CS
SCK
MOSI
MISO
+3.3V
GND
PWM
INT
RX
TX
SCL
SDA
+5V
GND
MIKROBUS DEVICE CONN.
C1
100nF
1
2
3
4
5
GND
ID
D+
D-
VBUS
CN1
USB MINIB
USB-D_P
USB-D_N
FP1
VCC-IO
1
2
3
4
5
6
7 8
9
10
11
12
13
14
USB-D_P
USB-D_N
C5
470pF
D1
PMEG3010ER
SDA
SCLRX
TX
RX
TX
R1
2K2
R2
2K2
R4
2K2
VCC-3.3V
C2
100nF
VCC-5VVCC-3.3V
VCC-5VVCC-3.3V
VCC-5V
VCC-IO
VCC-IO
VCC-IO
GP0
GP1
GP2 GP3
J2
J3
GP0
GP1
GP0-HDR
LED_URx
GP1-HDR
LED_UTx
SDA
J4
GP3
GP3-HDR
LED_I2C
VCC-IO
SCL
I/O LEVEL
GND
R3
2K2
PWR
VCC-IO
R8
2K2
U_RX
VCC-IO
LED_URx
R9
2K2
U_TX
VCC-IO
LED_UTx
R10
2K2
I2C_DAT
VCC-IO
LED_I2C
1
2
3
4
HD1
M1X4
1
2
3
4
HD2
M1X4
GP0-HDR
GP1-HDR
GP2
VCC-IO
GP3-HDR SDA
SCL
R11 1K
RST/EN
RST/EN
C4
2.2uF
R6
39K
R5
287K
1
2
3
IN
GND
OUT
5
4
EN ADJ
U2
AP7331-ADJ
C3
2.2uF
R7
0R
VCC-3.3V
VCC-5V
D2
PMEG3010ER
RST/EN
VDD
GP0
GP1
RST
URx
UTx
GP2 GP3
SDA
SCL
Vusb
D-
D+
VSS
U1
MCP2221
8. Code examples
MikroElektronika oers free tech support
(www.mikroe.com/support) until the end of
the product’s lifetime, so if something goes
wrong, we’re ready and willing to help!
Once you have done all the necessary
preparations, it’s time to get your click board
™
up and running. We have provided examples
for mikroC
™
, mikroBasic
™
and mikroPascal
™
compilers on our Libstock website. Just
download them and you are ready to start.
.com
6. Dimensions
MikroElektronika assumes no responsibility
or liability for any errors or inaccuracies
that may appear in the present document.
Specication and information contained in
the present schematic are subject to change
at any time without notice.
Copyright © 2015 MikroElektronika.
All rights reserved.
mm mils
LENGTH
42.9 1690
WIDTH
25.4 1000
HEIGHT*
3.9 154
5. Schematic
9. Support
* without headers
10. Disclaimer
GP SEL is for specifying whether the GPO I/
Os will be connected to the pinout, or used to
power signal LEDs. I/O LEVEL jumpers are for
switching between 3.3V or 5V logic.
25.4 mm / 1000 mils
42.9 mm / 1690 mils
7. Two sets of SMD jumpers