Datasheet

© 2009-2011 Microchip Technology Inc. DS61156G-page 187
PIC32MX5XX/6XX/7XX
TABLE 31-7: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD)
DC CHARACTERISTICS
Standard Operating Conditions: 2.3V to 3.6V
(unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for Industrial
-40°C
≤ TA ≤ +105°C for V-Temp
Param.
No.
Typical
(2)
Max. Units Conditions
Power-Down Current (I
PD)
(1)
for PIC32MX575/675/695/775 Family Devices
DC40 10 40 μA-40°C
2.3V Base Power-Down Current
(Note 6)
DC40a 36 100 μA +25°C
DC40b 400 720
μA +85°C
DC40h 900 1800 µA +105°C
DC40c 41 120
μA +25°C 3.3V Base Power-Down Current
DC40d 22 80
μA-40°C
3.6V Base Power-Down Current
DC40e 42 120
μA +25°C
DC40g 315 400
(5)
μA +70°C
DC40f 410 800
μA +85°C
DC40i 1000 2000 µA +105°C
Module Differential Current for PIC32MX575/675/695/775 Family Devices
DC41 — 10 μA — 2.3V Watchdog Timer Current: ΔIWDT (Notes 3,6)
DC41a 5 — μA — 3.3V Watchdog Timer Current: ΔIWDT (Note 3)
DC41b — 20 μA — 3.6V Watchdog Timer Current: ΔIWDT (Note 3)
DC42 — 40 μA — 2.3V RTCC + Timer1 w/32 kHz Crystal: ΔIRTCC (Notes 3,6)
DC42a 23 — μA — 3.3V RTCC + Timer1 w/32 kHz Crystal: ΔIRTCC (Note 3)
DC42b — 50 μA — 3.6V RTCC + Timer1 w/32 kHz Crystal: ΔIRTCC (Note 3)
DC43 — 1300 μA — 2.5V ADC: ΔIADC (Notes 3,4,6)
DC43a 1100 — μA — 3.3V ADC: ΔIADC (Notes 3,4)
DC43b — 1300 μA — 3.6V ADC: ΔIADC (Notes 3,4)
Power-Down Current (I
PD)
(1,7)
for PIC32MX534/564/664/764 Family Devices
DC40g 12 40 μA-40°C
2.3V Base Power-Down Current
(Note 6)DC40h 20 100 μA +25°C
DC40i 210 720
μA +85°C
DC40j 20 120
μA +25°C 3.3V Base Power-Down Current
DC40k 15 80
μA-40°C
3.6V Base Power-Down Current
DC40l 20 120
μA +25°C
DC40m 113 400
(5)
μA +70°C
DC40n 210 800
μA +85°C
Note 1: Base IPD is measured with all digital peripheral modules and being clocked, CPU clock is disabled. All I/Os
are configured as inputs and pulled low. WDT and FSCM are disabled.
2: Data in the “Typical” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance
only and are not tested.
3: The Δ current is the additional current consumed when the module is enabled. This current should be
added to the base I
PD current.
4: Test conditions for ADC module differential current are as follows: Internal ADC RC oscillator enabled.
5: Data is characterized at +70°C and not tested. Parameter is for design guidance only.
6: This parameter is characterized, but not tested in manufacturing.
7: This information is preliminary.