Datasheet

ManualsBrandsMIKROELEKTRONIKA ManualsMikroElektronika Development KitsPCB extension board

181

182

183

184

185

186

187

188

189

190

PIC32MX5XX/6XX/7XX

TABLE 31-6: DC CHARACTERISTICS: IDLE CURRENT (IIDLE)

DC CHARACTERISTICS

Standard Operating Conditions: 2.3V to 3.6V

(unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for Industrial

-40°C

≤ TA ≤ +105°C for V-Temp

Parameter

No.

Typical

(2)

Max. Units Conditions

Idle Current (I

IDLE): Core Off, Clock on Base Current

(1)

for PIC32MX575/675/695/775 Family Devices

DC30 4.5 6.5 mA -40ºC, +25ºC, +85ºC

—4 MHz

DC30b 5 7 mA +105°C

DC31 13 15 mA -40ºC, +25ºC, +85ºC — 25 MHz

(Note 3)

DC32 28 30 mA -40ºC, +25ºC, +85ºC — 60 MHz (Note 3)

DC33 36 42 mA -40ºC, +25ºC, +85ºC

—80 MHz

DC33b 39 45 mA +105°C

DC34 — 40 µA -40°C

2.3V

LPRC (31 kHz)

(Note 3)

DC34a — 75 µA +25°C

DC34b — 800 µA +85°C

DC34c — 1000 µA +105°C

DC35 35 — µA -40°C

3.3V

DC35a 65 — µA +25°C

DC35b 600 — µA +85°C

DC35c 800 — µA +105°C

DC36 — 43 µA -40°C

3.6V

DC36a — 106 µA +25°C

DC36b — 800 µA +85°C

DC36c — 1000 µA +105°C

Idle Current (IIDLE): Core Off, Clock on Base Current

(1,4)

for PIC32MX534/564/664/764 Family Devices

DC30a 1.5 6.5 mA -40ºC, +25ºC, +85ºC — 4 MHz

DC31a 7 15 mA -40ºC, +25ºC, +85ºC — 25 MHz

(Note 3)

DC32a 13 30 mA -40ºC, +25ºC, +85ºC — 60 MHz (Note 3)

DC33a 17 42 mA -40ºC, +25ºC, +85ºC — 80 MHz

DC34c — 40 µA -40°C

2.3V

LPRC (31 kHz)

(Note 3)

DC34d — 75 µA +25°C

DC34e — 800 µA +85°C

DC35c 30 — µA -40°C

3.3VDC35d 55 — µA +25°C

DC35e 230 — µA +85°C

DC36c — 43 µA -40°C

3.6VDC36d — 106 µA +25°C

DC36e — 800 µA +85°C

Note 1: The test conditions for base IDLE current measurements are as follows: System clock is enabled and

PBCLK divisor = 1:8. CPU in Idle mode (CPU core Halted). Only digital peripheral modules are enabled

(ON bit =

1) and being clocked. WDT and FSCM are disabled. All I/O pins are configured as inputs and

pulled to V

SS. MCLR = VDD.

2: Data in “Typical” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance

only and are not tested.

3: This parameter is characterized, but not tested in manufacturing.

4: This information is preliminary.