User manual

52
REV ADJ2.5 P2
DUAL PATH PRINTER WITH RADJ paper guide set to 2.50” on path #2
REV ADJ2.5 BOTH
DUAL PATH PRINTER WITH REV RADJ paper guide set to 2.50” on both paths
REV ADJ2.7 P1
DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 2.70”
REV ADJ2.7 P2
DUAL PATH PRINTER WITH RADJ paper guide set to 2.70” on path #2
REV ADJ2.7 BOTH
DUAL PATH PRINTER WITH REV RADJ paper guide set to 2.70” on both paths
REV ADJ3 P1
DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 3”
REV ADJ3 P2
DUAL PATH PRINTER WITH RADJ p
aper guide set to 3” on path #2
REV ADJ3 BOTH
DUAL PATH PRINTER WITH REV RADJ paper guide set to 3” on both paths
REV ADJ2.125 P1
DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 2.125”
REV ADJ2.125 P2
DUAL PATH PRINTER WITH RADJ paper guide set to 2.125” on path #2
REV ADJ2.125 BTH
DUAL PATH PRINTER WITH REV RADJ paper guide set to 2.125” on both paths
REV ADJ3.25 P1
DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 3.25”
REV ADJ3.25 P2
DUAL PATH PRINTER WITH RADJ paper guide set to 3.25” on path #2
REV ADJ3.25 BTH
DUAL PATH PRINTER WITH REV RADJ paper guide set to 3.25” on both paths
PATH TYPE? Defines the number of paper paths used.
Here are the following choices:
PATH1
Locks a Dual path printer onto path #1 (all single path printers)
PATH2
Locks a Dual path printer onto path #2
DUAL
Is used for Dual path printer
DUAL SUPPLY
Please consult your Programming Guide (Dual Printer Supplement)
VENTEK DUAL
Special setting only used by certain customers.
BUFFER MODE? Defines when the printer will go busy.
Here are the following choices:
SINGLE MODE1
Go busy after each print command inserted in buffer
SINGLE MODE2
Go busy after receiving <p> command
MULTIPLE MODE
Go busy when the input buffer is full (~ 4k)
CLEAR DOWNLOAD? Clears those items downloaded by the operator (PCX or softfonts).
Your choices are YES or NO.
DEFAULT SETTING Resets the printer back to the factory default setting.
Your choices are YES or NO.
INC CUT1 COUNT? Enables the operator to move the cut or tear position to the left (towards the
ticket entrace area). Cut counts are increments of .003” for 300dpi and .005” for 200dpi. Depressing
CHOICES changes the count value. 16 is factory default.
DEC CUT1 COUNT? Enables the operator to move the cut or tear position to right (towards the
ticket exit area). Cut counts are decrements of .003” for 300dpi and .005” for 200dpi. Depressing
CHOICES changes the count value. 16 is factory default.
INC CUT2 COUNT? Same as INC CUT1 COUNT? But effects path #2 on a dual path printer.
DEC CUT2 COUNT? Same as DEC CUT1 COUNT? But effects path #2 on a dual path printer.
2-SIDED PRINTER? Only used with 2S ticket printers.
Your choices are YES (Enabled) or NO (Disabled). NO is factory default.
PARK TICKET? Reverse the ticket to the print position after the last ticket in a group has been
printed. Please consult your Programming Guide. Your choices are YES (Enabled) or NO (Disabled).
NO is factory default.
TICKET MODE? Defines how the printer will treat multiple tickets. Please consult your
Programming Guide. Your choices are SINGLE or MULTIPLE. MULTIPLE is factory default.
PRINT MODE? Defines the automatic ticket length calculation feature.
THERMAL - The printer will feed out and then retract a ticket during this measurement.