User manual
51
The following is an overview of what each Menu option does:
BAUD RATE?
Controls the serial interface baud rate, parity bit, data bits and stop bits.
Here are the following choices:
MINI/MICRO?
Defines the type of printer
.
MINI Is for a printer with a Silent Cutter Assembly (SC2) (Mini, Mini Plus, Mini MB, Dual Mini)
MICRO Is for a printer without a SC2 (Micro, Micro Plus, Micro MB, Dual Micro)
PRINT SPEED?
Controls the speed the ticket travels at. Also effects the print quality.
The numbers range from 0 - FASTEST to 7 - SLOWEST. 3 is factory default.
DIAGNOSTIC MODE?
Please consult your Programming Guide
Your choices are YES or NO. NO is factory default.
TICKET TYPE?
Defines how the optos are configured on the paper guide assembly.
Here are the following choices:
NORMAL
Both optos are inline with each other (usually mounted on a black bracket)
ATM
Feed opto is mounted under the thermal head and cut opto is attached to the cutter assy.
LABEL
Same as ATM but the cut opto is a see through type.
SPECIAL TICKET
This option is for a Micro MB or a printer with a ticket load switch
STATUS ENABLED?
Sets status response protocols.
Here are the following choices:
NONE
Disables the XON/XOFF and status response protocols
SERIAL
Enables the XON/XOFF and status response protocol for the serial port.
PARALLEL
Enables bi
-
directional parallel status responses if printer is configured as bi
-
directional.
SER/PAR
Enables both bi-directional parallel and serial status responses.
USB
Enables USB status responses
USB/SER
Enables USB and serial status responses
USB/PAR
Enables USB and bi-directional parallel
USB/SER/PAR
Enables USB, bi-directional parallel and serial status responses
TRANSPARENT MODE?
Please consult your Programming Guide
Your choices are YES (Enabled) or NO (Disabled).
PAPER MODE?
Is generally used only for test purposes. It may also be used on roll stock with no
black marks on the ticket. Your choices are YES (Enabled) or NO (Disabled). NO is factory default.
HEAD DPI?
Defines thermal head dpi (dots per inch) - choices are 200, 300 or 600.
This feature is set at the factory and should not be changed.
SPECIAL HEAD?
Is used when a special paper path size is installed (2.125”, 2.5”, 2.7”….)
Here are the following choices: This feature is set at the factory.
NO No special head
ON P1
DUAL & SINGLE PATH PRINTER ONLY (fixed path)
ON P2
DUAL PATH PRINTER ONLY on path #2 (fixed path)
ON BOTH
DUAL PATH PRINTER ONLY on both paths (fixed path)
REV ADJ2 P1
DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 2”
REV ADJ2 P2
DUAL PATH PRINTER WITH RADJ paper guide set to 2” on path #2
REV ADJ2 BOTH
DUAL PATH PRINTER WITH REV RADJ paper guide set to 2” on both paths
REV ADJ2.5 P1
DUAL & SINGLE PATH PRINTER WITH RADJ paper guide set to 2.50”
1200,N,8,1
4800,N,8,1
19200,N,8,1
38400,E,7,1
1200,E,7,1 4800,E,7,1 19200,E,7,1 57600,N,8,1
1200,O,7,1 4800,O,7,1 19200,0,7,1 57600,E,7,1
2400,N,8,1 9600,N,8,1 28800,N,8,1 115200,N,8,1
2400,E,7,1 9600,E,7,1 28800,E,7,1 115200,E,7,1
2400,O,7,1 9600,0,7,1 38400,N,8,1