Manual LOGO 700 Mikado Model Helicopters GmbH • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de © Mikado Model Helicopters GmbH 2012, V1.
Index Safety Instructions/ Tools for Assembly & RC Equipment 1 Mainframe 2 Servo Mounting 3 Main Gear 4 Landing Struts and Canopy Holder 5 Motor Installation 6 Tail Rotor 7 Torque Tube 8 Tail Boom Mounting 9 Tail Boom Brace 10 Swashplate 11 Rotor Head 12 Wiring RC Components 13 Mounting ESC and Voltage Regulator 14 Battery Mounting 15 Main Rotor Blades and Tail Rotor Blades 16 Canopy and Overview 17 Over
Please check if the RC-plate is fitted tightly between the frames, so that it cannot move. If the RC-plate is loose, please apply glue (speed glue or hot glue) to fix. A moving RC-plate can lead to vibrations and malfunction of the gyro sensor! Bag 1 + 2 M3x5 M2,5x12 The mainframe of the LOGO 700 XXtreme is pre-assembled. You will find it in Box 1. Note that the screws are not secured. You must use Loctite to secure all screws in the mainframe.
2 Servo Mounting A B M2,5x8 Bag 3 4x M2,5 3x M3 1x M2 4x M2,5x10 M2,5x8 12x M2,5x6 M2,5x8 8x M2,5x10 4x 3x M2,5x10 M2,5x8 1x 20x M2,5x12 M3x12 M2x10 M2,5 3x 16mm 16mm 16mm 16mm C D M2,5x8 1x M2x10 In the kit you will find servo mounting sets for Futaba/JR HV (11mm) servos and Savöx HV (10mm) servos Two different sets of servo arms are included in the kit, one for JR servos, and one for Futaba/Savöx servos.
3 Main Gear 0,5mm Bag 4 6x 0,5mm 1mm Before mounting the main rotor shaft and the main gear, you need to remove the third bearing block. In addition you need to push the motor plate all the way to the back. werden. M3x12 2x M3x12 1x 4x20 3x 14x20x1 2x 14x20x0,5 Please apply grease to the one-way bearing! 1mm 0,5mm After mounting the main gear, it will show slight axial play. This is intended and will make installation of the pinion easier.
4 Landing Struts and Canopy Holder M3x10 Bag 5 4x Ø5x44mm Bag 5 contains two additional 1 mm washers. If necessary, you may adjust the distance of the canopy bolts with these. M3x16 Ø5x42mm M3x5 M4x10 4x M3x16 2x M3x10 4x M3x5 2x 3x5x1,2 2x M3x6 M4x10 M4x10 Glue the four caps to the ends of the landing skids.
5 Motor Installation Unscrew the motor plate and take it out of the chassis. Additionally you need the losen the screws of the counter-bearing. Bag 6 4x 1x 4x Solder the 5.5 mm gold connectors to the motor. Make sure to use a soldering iron large enough to create an adequate connection. A poor connection can lead to irregular behavior of the motor or the ESC. High-current plugs like these need to be perfectly isolated at all times when connected. Otherwise there is a high risk of shorting.
6 Tail Rotor M2,5x6 Bag 7 M3x16 M2,5x12 M3x16 M3x12 M2,5x6 M2,5 Stop 3x6x2,5 M2x10 Mount the distance ring so that its surface with the shoulder shows in the direction of the ball bearing. 2x M2x10 1x M2,5x16 2x M3x20 2x M3 1x M2,5 2x 3x7x0,5 2x 5x10x4 4x 5x10x4 6x 4,5x2 2x 7x10x0,5 2x 5x7,8x0,6 M2x12 5x10x4 M3x24 2x M3 Stop 6x9x0,2 3x5,5x0,2 1x 5x10x4 M3x20 Please check the gear back lash after every flight. If gear back lash has increased, please add washers.
7 Torque Tube Torque Tube assembly Bag 8 + 12 You need to mount the torque tube. To do so, please position the four torque tube holders on the aluminium boom. Then glue them on. Using adhesive tape in addition will prevent the holders from moving, should they become lose.
8 Tail Boom Mounting M2,5x12 Loctite M3x16 M2,5x12 M3x12 M2,5x12 Loctite M2,5x6 M2,5x6 M2,5x12 M3x12 Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 10
9 Tail Boom Brace M2 Stop Bag 8 M2x5 M2x6 M3x12 M2,5x10 3x5x2 M3x12 Loctite Please glue the ball links of the tail boom support with 5-min epoxy. Note when mounting the ball links: If you find it hard to clip the ball link on, turn it 180°. One side of the ball link will clip on easily. The other one is too tight to clip on easily.
10 Swashplate Loctite Bag 9 4x7x0,8 5x 3x 33mm M2,5x6 4x7x0,8 6x 4x7x0,8 5x 4x7x0,8 M2,5 Note when mounting the ball links: If you find it hard to clip the ball link on, turn it 180°. One side of the ball link will clip on easily. The other one is too tight to clip on easily.
11 Rotor Head 11 Rotor Head 11 Rotor Head Bag 10 2x M3x16 4x M3x14 2x Loctite M5x34 M3x16 2x 2x M5 3x5x0,5 2x M5x34 M6x10 2x 6,2x12x1 M3x14 Loctite Loctite Please apply grease to the O-rings and to the inner surface of the yoke.
11 Rotor Head Bag 10 4x M3x16 1x M4x25 2x 4x M4 Stop 4x M3x16 Loctite 30mm M3x16 (2x) Loctite Loctite Note when mounting the ball links: If you find it hard to clip the ball link on, turn it 180°. One side of the ball link will clip on easily. The other one is too tight to clip on easily.
12 Wiring RC Components BEC oder Lipo-Empfängerakku 2S (1300-1500 mAh) You are required to use the adapter wire for the connection between the YGEESC and the VBar unit. orange YGE ESC: The YGE 160 provided in this combo is a special version ESC which is already programmed. It will function exclusively in combination with the governor function of VBar. For programming the governor function, please follow the steps in the VBar software shown in the two screen shots below.
13 Mounting ESC and Voltage Regulator Please attach the three motor wires to the carbon plate, using cable straps. The wires leading to the motor must be attached in such a way that they cannot move. For mounting the ESC please use the plastic spacers included here. The connection to the carbon plate must not be electroconductive. This is to avoid short-outs. Attach the BEC using cable straps and double-sided tape. Take special care when placing the wires.
14 Battery Mounting The 12-cell lipo battery to be used with the LOGO 700 XXtreme needs to be mounted on the carbon battery plate, which is attached to the chassis by four screws. In this way the battery sits safely and is protected from vibration. You must check before each flight that the battery is secured tightly by three velcro strips and that the mounting plate is securely fastened to the helicopter. The gold connectors of the batteries should have a minimum diameter of 4 mm.
15 Main Rotor Blades and Tail Rotor Blades Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 18
16 Canopy and Overview The canopy of the LOGO 700 XXtreme is mounted via six attachment points. The four attachment points in the front ensure that the canopy sits well on the chassis during flight. have a guiding function. In the back, the canopy is attached by two rubber grommets. You will find another, high-quality, set of rubber grommets included in the kit. You may use these, if desired. Important note: A special feature of the Logo 700 XXtreme canopy ist that it the back part is fully closed.
17 Overview Spare Parts Mainframe 4757 4732 4740 4587 Savox 4588 Futaba/JR HV 4550 M2,5x8 4549 4739 4546 4544 4547 4515 4548 4757 4739 4738 4740 4537 M2,5x8 4517 4543 4545 4712 M3x12 M3x12 (6x) M4x5 4514 4736 4488 - 17 teeth 4489 - 18 teeth 4490 - 19 teeth M4x10 M4x12 4757 4738 4290 4590 4513 M3x5 2469 4517 4711 Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 20
17 Overview Spare Parts Mainframe 4733 M3x10 4489 (Set) M3x10 (4x) 4524 (2,5mm) 4535 4757 4734 4546 4469 4541 (3mm) 4541 (3mm) M3x8 4585 (3x) 4524 (2,5mm) M3x8 M2,5x6 M2,5x6 4757 4758 M2,5x6 4541 (3mm) M3x10 4757 Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 21
18 Overview Spare Parts Gear Box M2,5x8 (6x) 4519 4522 M3x3 M2,5x6 (2x) 4520 M2,5x12 (2x) 4518 4525 4524 4521 6x13x5 M2,5x12 (4x) 4523 4516 4521 6x13x5 4519 4520 Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 22
19 Overview Spare Parts Tail Boom 4562 3x5x2 M3 Stopp M3x16 4561 M2x12 M3x16 4759 (Set) 4755 4756 (Set) 4760 (2x) Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 23
20 Overview Spare Parts Tail Rotor M2,5x6 4565 4581 M2,5x12 M2,5x12 M3x16 M2,5x6 4567 M3x20 4522 M2,5x6 M2,5x8 4584 M3x16 M2,5x16 4566 4524 4583 4763 4525 4571 M2,5x12 4570 4568 2470 4564 2470 4582 M3x8 4569 Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 24
21 Overview Spare Parts Rotor Head 4700 4508 M4 4786 (M5x32) 4704 4705 4706 M3x14 4792 (2x) 4703 4701 M4x25 4702 M3x16 4509 4507 (2x) 4703 M5 Stopp Manual LOGO 700 XXTREME - ©Mikado Model Helicopters GmbH - Page 25
