Installation Guide

27 MM560 Installation Instructions
With gate in CLOSED position, turn control box power switch
to ON.
Press button on opener remote; gate should start opening. Press but-
ton on opener remote again when gate is in desired OPEN position.
Press and hold the “LEARN MASTER LIMIT” button for 5
seconds, or until the alarm sounds.
Press button on opener remote to fully close gate. Open limit is
set upon reaching the fully closed limit. Test and, if needed reset
and start over.
ON
15
FUSE
BAT T+
BAT T-
1 2 3 4
ON
STATUS
LEARN RMT
RECEIVER
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3 S4
ALM
S2
OFF
SOFT START OFF WARNING OFF OPEN PULL SLV OPEN DLY. MODE1 OFF MODE2 OFF
ON ON PUSH SIMULT. ON ON
120 MIN MAX
CHARGING
PWR IN
GTO RCVR.
WHT
BLU
BRN
ORG
RED
BLK
GRN
WHT
BLU
BRN
ORG
RED
BLK
GRN
COM
GRN
BLK
RED
CYCLE
SAFETY
EXIT
SHADOW
OPEN
EDGE
COM
MASTER CABLESLAVE CABLE
CONTROL INPUTS
AUTO CLOSE TIME STALL FORCE
CLOSE
EDGE
1 2 3 4 5 6 7
POWER
INPUTS
LOCK
PWR
AUX
RLY
CONTROL
OUTPUTS
1
2
3
2
1
15
FUSE
BAT T+
BAT T-
1 2 3 4
ON
STATUS
LEARN RMT
RECEIVER
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3 S4
ALM
S2
OFF
SOFT START OFF WARNING OFF OPEN PULL SLV OPEN DLY. MODE1 OFF MODE2 OFF
ON ON PUSH SIMULT. ON ON
120 MIN MAX
GTO RCVR.
WHT
BLU
BRN
ORG
RED
BLK
GRN
WHT
BLU
BRN
ORG
RED
BLK
GRN
COM
GRN
BLK
RED
CYCLE
SAFETY
EXIT
SHADOW
OPEN
EDGE
COM
GTO
TRANSF
LOCK
PWR
AUX
RLY
POWER
INPUTS
CONTROL
INPUTS
MASTER CABLESLAVE CABLE
CONTROL INPUTS
AUTO CLOSE TIME STALL FORCE
CLOSE
EDGE
18 VAC
or
SOLAR
GTO
LOCK
AUX
1
2
3
4
5
6 7
15
FUSE
BAT T+
BAT T-
1 2 3 4
ON
STATUS
LEARN RMT
RECEIVER
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3 S4
ALM
S2
OFF
SOFT START OFF WARNING OFF OPEN PULL SLV OPEN DLY. MODE1 OFF MODE2 OFF
ON ON PUSH SIMULT. ON ON
120 MIN MAX
GTO RCVR.
WHT
BLU
BRN
ORG
RED
BLK
GRN
WHT
BLU
BRN
ORG
RED
BLK
GRN
COM
GRN
BLK
RED
CYCLE
SAFETY
EXIT
SHADOW
OPEN
EDGE
COM
MASTER CABLESLAVE CABLE
CONTROL INPUTS
AUTO CLOSE TIME STALL FORCE
CLOSE
EDGE
1 2 3 4 5 6 7
POWER
INPUTS
LOCK
PWR
AUX
RLY
CONTROL
OUTPUTS
ON
LEARN RMT
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3
S4
S2
ON
ON
PUSH
SIMULT.
ON
ON
MAX
3
2
4
1
Control Box Settings
Setting Push-to-Open (Open) Gate Limit (for pull-to-open go to pg. 26)
Press button on opener remote to close gate.
Hold the “LEARN MASTER LIMIT” button for 10 seconds,
or until the alarm sounds to clear. Go back to setting open gate
limit step 1 at the top of this page.
2
3
5
1
15
FUSE
BAT T+
BAT T-
1 2 3 4
ON
STATUS
LEARN RMT
RECEIVER
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3 S4
ALM
S2
OFF
SOFT START OFF WARNING OFF OPEN PULL SLV OPEN DLY. MODE1 OFF MODE2 OFF
ON ON PUSH SIMULT. ON ON
120 MIN MAX
GTO RCVR.
WHT
BLU
BRN
ORG
RED
BLK
GRN
WHT
BLU
BRN
ORG
RED
BLK
GRN
COM
GRN
BLK
RED
CYCLE
SAFETY
EXIT
SHADOW
OPEN
EDGE
COM
GTO
TRANSF
LOCK
PWR
AUX
RLY
POWER
INPUTS
CONTROL
INPUTS
MASTER CABLESLAVE CABLE
CONTROL INPUTS
AUTO CLOSE TIME STALL FORCE
CLOSE
EDGE
18 VAC
or
SOLAR
GTO
LOCK
AUX
1 2 3 4 5 6 7
ON
LEARN RMT
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3
S4
S2
ON
ON
PUSH
SIMULT.
ON
ON
MAX
6
Resetting Open Gate Limit
NOTE: if the gate stops and reverses see “setting obstruction stall
force” page 28.
NOTE: If the unit does not
respond to the transmitter see
“setting personal transmitter
code” page 29