SDS
Table Of Contents
- 1. PRODUCT AND COMPANY IDENTIFICATION
- 2. HAZARDS IDENTIFICATION
- 3. COMPOSITION/INFORMATION ON INGREDIENTS
- 5. FIRE-FIGHTING MEASURES
- 6. ACCIDENTAL RELEASE MEASURES
- 7. HANDLING AND STORAGE
- 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
- 8.1. Control parameters
- 8.2. Exposure controls
- :
- :
- :
- :
- :
- :
- :
- :
- :
- :
- :
- :
- SERIOUS EYE DAMAGE/IRRITATION
- RESPIRATORY OR SKIN SENSITIZATION
- MUTAGENICITY
- CARCINOGENICITY
- REPRODUCTIVE TOXICITY
- >0.1% total concentration is given below:
- No data is available on mutagenicity for this mixture. STOT- Single exposure data on hazardous components
- STOT – REPEATED EXPOSURE
- ASPIRATION HAZARD
- >10.0% total concentration is given below:
- GENERAL ECOLOGICAL TOXICITY
- PERSISTANCE AND BIODEGRADABILITY
- BIOACCUMALATIVE POTENTIAL
- MOBILITY IN SOIL
- >1.0% total concentration is given below:
- No specific data on other adverse effects is available for this mixture. Additional data on adverse effects for hazardous components >1.0% total concentration is given below:
Product name: Mighty Mint Pest Repellent Concentrate
Revision Date: Jan 29 2021
(includes fire-fighting helmet, coat, trousers, boots, and
gloves). If protective equipment is not available or not
used, fight fire from a protected location or safe distance.
6. ACCIDENTAL RELEASE MEASURES
6.1.
Personal precautions, protective equipment and accidental emergency procedures
PERSONAL PRECAUTIONS : Avoid inhalation and contact with skin and eyes. A self-
contained breathing apparatus is recommended in case
of a major spill.
6.2.
Environmental precaution
ENVIRONMENTAL PRECAUTION : Prevent from entering into soil, ditches, sewers,
waterways and/or groundwater.
6.3.
Methods and materials for containment and cleaning up
FOR CONTAINMENT AND CLEAN UP : Clean up spillage promptly. Remove ignition sources.
Provide adequate ventilation. Avoid excessive inhalation
of vapors. Gross spillage should be contained by use of
sand or inert powder and disposed of according to the
local regulations.
7. HANDLING AND STORAGE
7.1.
Precautions for safe handling
PRECAUTIONS FOR SAFE HANDLING : Avoid excessive inhalation of concentrated vapors,
contact with skin and eyes. Follow good manufacturing
practices for housekeeping and personal hygiene. Wash
any exposed skin immediately after any chemical
contact, before breaks and meals and at the end of the
work period. Contaminated clothing and shoes should be
thoroughly cleaned before re-use. Keep away from
ignition sources and naked flame.
7.2.
Conditions for safe storage, including any incompatibilities
STORAGE CONDITIONS : Store in a cool, dry ventilated area away from heat
sources. Keep containers tightly closed when not in
use.
INCOMPATIBLE MATERIALS : Strong oxidizing agents.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1.
Control parameters
CONTROL PARAMETERS
8.2.
Exposure controls
: If exposure limits exist, they are listed below. If no exposure
limits are displayed, then no values are applicable.
ENGINEERING CONTROLS : If appropriate, isolate mixing rooms and other areas
where this material is used or openly handled. Apply
local exhaust system or maintain these areas under
negative air pressure relative to the rest of the operation.
Ensure access to showers, eye wash stations and have
adequate ventilation systems.
SKIN PROTECTION :
Avoid skin contact. Use gloves chemically resistant to
this material when prolonged or frequently repeated
contact could occur.
EYE PROTECTION : Wear goggles.
RESPIRATORY PROTECTION : If exposure limits are exceeded or irritation is
experienced, NIOSH/MSHA approved respiratory
protection should be worn. Positive-pressure supplied air
respirators may be required for high airborne