Model C-SPS-1-18NG(LP) #of burners and control method 1 set Independen t control C-SPS-2-18NG(LP) 2 sets Independen t control C-SPS-1-18L -NG(LP) 1 set Independen t control C-SPS-2-18L -NG(LP) 2 sets Independen t control Gas Species Intake-tube pressure （in.W.C.） Per BTU B.T.U./h Total BTU B.T.U./h Nozzle No. Natural Gas L.P. Gas Natural Gas 4 80,000 80,000 #32 10 80,000 80,000 #49 4 80,000 160,000 #32 L.P.6.1、Unpacking and Installation Please dispose of all packaging materials and residues after unpacking; Check the equipment. If it is damaged, please keep wrappers and receipts which must be signed by the carrier representative (Driver), and contact the carriers to pursue a claim within 15 days after receiving; Check all accessories complete.
Thread glue must be resistant to the action of liquefied petroleum gases. Warning! Use soap water or testing instrument to test whether piping joint leaks or not before using, and forbid using an open flame to test! After installing completely, you should check gas supply pressure. Use a pressure gauge which is equipped with liquid (such as U-type pressure gauge, the minimum value is 0.1mbar) or a digital pressure gauge to test.
all heat and flames, and call 911. Safety information can be obtained from your local gas suppliers.
8.2、Igniting the main burner Revolve the main fire control valve knob anticlockwise after lighting the pilot light, then the main fire burner is lighted by the pilot light. The power of burner increases as revolving angel increases. When knob reaches to " ", burner is in the maximum power (Fig.4). Fig.2 Fig.3 C-SPS-1-18-NG(LP) CONTROL PANEL Fig.
8.3、Turn off the valve Revolve the control valve knob clockwise to "0" (Fig.1), so that extinguish flame of the main burner, but the pilot light still works. After turn off the equipment, the main fire should be stop more than 5 minutes before next use. 8.4、Stove Operation Before using the stove for the first time, please use a mild detergent to wipe it clean. Do not use corrosive or abrasives detergent.
Caution: Each burner damper has been adjusted before delivery (once air input), Normal use without adjustment but only switching gas. Adjust only by authorized and licensed technicians. Fig.7 Fig.8 Fig.9 9.
Recommended cleaning methods
Items Body Methods Times Wipe it with a soft cloth and mild detergent; daily Turn off valves when not in use; Control panel Wipe panel and control valve knob with daily mild detergent. Pull out catch tray from front body until the equipment cools down. Use a cloth with Catch tray cleaning agent to wipe unit surface, wipe up residue. Reinstall after cleaning. Per use Warning: if the catch tray is permitted to fill too high, should be cleaned! 10.1.Insufficient gas pressure in pipe Close gas and heard a sound of fire 1.Contact the local gas supply dept. 2.Not match nozzle aperture with 2.Adjust gas resources diameter 3.Flow of connection pipe is not enough 3.Increase allowable flow 4.Damper opening degree is too large 4.Adjust damper 1.Use bottom gas 1.Change gas 2.Not match nozzle aperture with 2.Adjust gas resources diameter Yellow flame and black smoke nozzle pipe’s nozzle 3.Not enough air to ignite 3.
Fig.
Matters No. 1 Dimensions Component name Qty Remark Code (mm)/Model 21206001001 457*515*432 C-SPS-1-18-NG(LP) 457*1045*432 C-SPS-2-18-NG(LP) 457*515*309 C-SPS-1-18L-NG(LP) 21206002001 21206003001 Body unit 1 21206004001 457*1045*309 C-SPS-2-18L-NG(LP) 4 2 301110001 Adjustable steel legs 6 4 C-SPS-1-18-NG(LP) Φ41.301060001 Needle type pressure joint 1 1/8"-27NPT 9 301060002 Needle type pressure joint screw arbor 1 M5*23 10 301080002 Galvanized flange surface nut 2 M6 11 301082002 Galvanized flat washer 2 Φ6.
0 17 18 19 20 21 22 301070011 301050015 21106002013 301060003 211060001011 21106002014 Brass hoop Brass street elbow Front burner outer pilot intake-tube Pilot light head Pilot light head stator Front burner inner pilot intake-tube 4 0 C-SPS-1-18-NG(LP) Φ10 24 25 301080008 301050014 21106002017 Brass lock nut Brass double male elbow Back burner outer ring main gas pipe C-SPS-1-18L-NG(LP) 4 C-SPS-2-18L-NG(LP) 0 C-SPS-1-18-NG(LP) 2 0 M16 turn to 3/8"-27UNS C-SPS-2-18-NG(LP)
0 26 21106002018 27、 21106002015 28 29 30 301020013 301010013 Back burner inner ring main gas pipe Back burner pilot light in-take tube Boiler cradle Boiler burner 1 0 C-SPS-1-18-NG(LP) Φ10*1.0 C-SPS-1-18L-NG(LP) 1 C-SPS-2-18L-NG(LP) 0 C-SPS-1-18-NG(LP) 2 0 Φ4.7*0.
Name Model Qty 12. Accessories List
Fig.11 Adjustable steel legs C-SPS-1-18-NG( C-SPS-2-18-NG( Fig.12 LP) LP) C-SPS-1-18L-NG Fig.Intertek N IT E US LI S T E D SA C CM D CM A T I O N LI S T Conforms to ANSI STD Z83.11-2016 Certified to CSA STD 1.8-2016 Conforms to NSF/ANSI STD.4 Intertek 4003935 Our products have the advantages of good durability and low maintenance charge. But to update some components and necessary maintenance, can prolong life length of the products. Contact the dealer for assistance. In order to avoid confusion, please follow the format in figure 10 and table 4.
