Installation manual

7
WIRELESS DA-605P DRIVE-ALERT
DA-605P CONTROL PANEL/RECEIVER GENERAL INFORMATION:
The DA-605P Drive-Alert’s receiver board is the same as the one used in the DA-600 receiver (see FIGURES 5-6). However,
the DA-605P does not have an internal whistle, nor a whistle switch. The advantages of the DA-605P over the DA-600 are the
DA-066 wireless chime transmitter which activates remote chimes as an alert. Any combination or quantity of the DA-068 Plug-in
Chimes and/or the DA-070 Battery-powered Portable Chimes may be used. Each chime is activated by a radio signal from the
DA-066 attached to the control panel. (See Accessories page). These chimes have a choice of three tones and volume control,
and can be used up to 100’ away from the control panel. As stated, the DA-068 plugs into any standard wall outlet. The DA-070 can
be taken into the backyard, out to the pool & etc.
DA-605P Control Panel with one DA-068 Plug-in Remote Chime and a DA-610TO Sensor/Transmitter
(Optional DA-070 Battery Operated Portable Chime pictured on Accessories Page)
TESTING FOR RADIO TRANSMITTER COMMUNICATION:
The alarm signal is used to turn on the 315 MHz radio signal in the push button located on the top of the DA-605P, which will
sound the remote chime. This signal will reach at least 100 feet to the chime. The radio module located on the top of the housing
contains a user accessible push button for test or “call” purposes. Internal to the module a 12 volt battery type A23 is contained
and should last about 3 years. This battery is activated only when testing the radio module to chime signal path and does not
have an effect on Drive-Alert operation. The chime can be tested independent of the Drive-Alert by pushing the button causing
the chime to sound. The enclosure of the radio module can be opened by pushing in on the bottom latch carefully with a screw-
driver and lifting up. Both the jumpers as well as the battery are now accessible. To re-seat the radio module enclosure carefully
align and place the enclosure top locking tabs and carefully push in the bottom latch until it snaps closed. The DA-068 Plug-in
Chimes and DA-070 Battery-powered Portable Chimes are factory preset. To change the sound remove jumper #8 under the small
cover on the back of the chime, To obtain a 1 note tone, remove only the jumper from the radio module while leaving the jumper in
the chime.
INSTALLATION:
For Sensor/Transmitter installation details see the sensor installation pages. The DA-068 & DA-070 chimes may be located in
multiple rooms and locations and the DA-605P can chime an unlimited number of chimes within 100+ feet of the Control Panel.
Simply plug the Control Panel in a standard wall outlet, where the signal from the DA-610 Sensor can reach it. Plug in the DA-068
Remote Chime(s) or place the DA-070 Portable Chimes in an area(s) of the house where an alert is desired. The DA-070 Battery
Operated Portable Chime needs two C batteries which will last about 3 years. For all options and operation instructions of the
chimes, see the instructions enclosed with the chimes.
Figure 5 shows a typical DA-605P control panel connection to a “line of sight wireless transmitter” like our DA-606LK Light Kit
FIGURE 5
For DA-605P control panel and DA-610TO/DA-611TO sensor specications, see previous page 6.
Free Lifetime Technical Support
800-473-0213 ~ [e-mail] ~ www.mierproducts.com
If your Drive-Alert does not
look like this, you may have
an older model. Please call
Mier’s free tech support line
at 800-473-0213
If your Drive-Alert does not
look like this, you may have
an older model. Please call
Mier’s free tech support line
at 800-473-0213
DA-605P to a DA-606LK
SIG ALA +5V GND +24DC NO NC C NO C
DC UN REG
Two Gray Wires attach to the last
two terminals (NO and C)