Operating instructions for condenser tumble dryer T 8823 C To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en - AU, NZ M.-Nr.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation. Rather than just throwing these materials away, please ensure they are offered for recycling.
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Notes on laundry care . . . . . . . . . . . . .
Contents Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Emptying the condensed water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Cleaning the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cleaning them with water . . . . . . . . . . . . . .
Contents Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Extending the range of the drying level for the "Cottons" programme. . . . . . . . . . 50 Extending the drying level for the "Minimum iron" programme . . .
Warning and Safety instructions ~ It is essential to read these instructions. This tumble dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance.
Warning and Safety instructions ~ The tumble dryer is not intended for outdoor use. ~ This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety. ~ This tumble dryer must not be installed and operated in mobile installations (e.g. on a ship).
Warning and Safety instructions Technical safety ~ Before setting up the tumble dryer, check it for any externally visible damage. Do not install or use a damaged tumble dryer. ~ Before connecting the tumble dryer, ensure that the connection data on the data plate (voltage and connected load) match the mains electricity supply. If in any doubt, consult a qualified electrician.
Warning and Safety instructions ~ If the connection cable is faulty, it must only be replaced by a Miele approved service technician to protect the user from danger.
Warning and Safety instructions Correct use , Caution! Risk of fire. To avoid the possible danger of fire, please read these warnings carefully. , A clogged filter is a fire hazard! The fluff filter must be cleaned after every programme. ~ Remove all objects from pockets such as lighters and matches. ~ To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: – Items which have not been washed.
Warning and Safety instructions When washing such heavily soiled items, ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. ~ Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire.
Warning and Safety instructions ~ In many programmes, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting). The programme is not finished until the cooling down phase is complete. Ensure that you always wait until the end of the programme before removing the laundry. ~ Warning: Do not switch the tumble dryer off before the end of the drying programme.
Warning and Safety instructions ~ The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way. ~ The fluff filters must be cleaned regularly. ~ The dryer must not be used without the condenser unit in place. ~ The fluff filters must be thoroughly dried after cleaning. Damp or wet filters could cause operational faults. ~ Do not install the tumble dryer in a room where there is a risk of frost occurring.
Warning and Safety instructions ~ Always close the door after use. This way you will avoid the danger of: – Children climbing onto or into the dryer or hiding things in it. – Pets or other small animals climbing into it. ~ The tumble dryer must not be hosed down. Accessories ~ Only use genuine Miele spare parts and accessories with this appliance. If non-Miele parts are used, warranty, performance and product liability claims may be invalidated.
Operating the tumble dryer Control panel a Low temperature button Delicate fabrics are dried at a lower temperature. g Check lights See Problem solving guide and After Sales service. b Drying level button Indicator lights show the selected drying level. h Start/Stop button For starting the programme selected and cancelling a programme once it has started. The button flashes when a programme is selected and then is on constantly when the programme has started. c Display See the next page.
Operating the tumble dryer The following information appears in the display: – Programme duration. – Programme sequence Drying Cooling down Finish – Check and fault messages The following functions are selected via the display – Programme duration Warm air, Cool air – Delay start You can delay the start of a programme. Once the Delay start time has finished, the programme begins automatically.
Notes on laundry care Care symbols Drying q Normal/higher temperature. r Reduced temperature: Select Low temperature for sensitive fabrics. s Do not tumble dry Ironing I Very hot. H Hot. G Warm. J Do not iron. Tips on drying – See the "Programme chart" for maximum recommended loads for each programme. Overloading can cause unnecessary wear and tear to the laundry, give a disappointing drying result and cause more creasing.
How to dry correctly Brief instructions The headings numbered (A, B, C ...) show the operating sequence and can be used as a brief guide to using your machine. A Sort the laundry Separate the washed laundry and sort it according to . . . . . . the drying level required, . . . the type of fibre or weave, . . . size, . . . the moisture content after spinning. In this way an even drying result will be achieved. ,Make sure that objects, e.g. detergent dispensing balls, have been removed from the laundry.
How to dry correctly D Select a programme Note You can extend the range of drying levels for some of the programmes (see "Programmable functions"). Woollens handcare, Gentle smoothing – this programme cannot be changed. Select Cool air/Warm air duration ^ Select the programme you want. The relevant indicator light will come on. Indicator lights for drying levels or Extra options and times may also be displayed.
How to dry correctly F Starting the programme The indicator light for the Start/Stop button will flash when a programme is being selected. The flashing indicates that a programme can be started. ^ Press the Start/Stop button. The Start/Stop button will now light up. Perfect Dry only flashes/illuminates during programmes with drying levels. It remains dark during time controlled programmes (see "Operating the tumble dryer"). Note: The duration shown in the display is only an estimate and can change.
Extra options/Delay start Extra options To begin Delay start The relevant indicator light will come on when selected. ^ Press the Start/Stop button. Low temperature For all delicate or minimum iron fabrics with the r symbol on the care label (e.g. acrylic garments). The programme duration is longer. On some programmes Low temperature is a standard part of the programme and so cannot be deselected. Buzzer A buzzer sounds (at intervals for a maximum of 1 hr) to let you know the programme has finished.
Programme chart Cottons Max. load: 7 kg* Extra dry, Normal Fabric type Single and multi-layered cotton fabrics such as towels, bathrobes, T-shirts and underwear. Notes – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for loopknit fabrics (e.g. T-shirts, underwear), as they have a tendency to shrink. Low temperature Low temperature (select this option for delicate fabrics with the r symbol on the care label).
Programme chart Woollens handcare Max. load: 2 kg* Fabric type Woollen fabrics. Notes – This programme only fluffs up woollen garments. They are not dried completely by this programme. – Remove garments as soon as the programme has finished and leave to finish drying at room temperature. Low temperature Low temperature cannot be deselected. Proofing Max. load: 2.
Programme chart Shirts Max. load: 2 kg* Normal, Hand iron Fabric type Shirts and blouses. Low temperature Low temperature (select this option for delicate fabrics with the r symbol on the care label). Cool air Fabric type Max. load: 7 kg* Any item which only needs airing. Warm air Max. load: 7 kg* Fabric type – "Voluminous" and multi-layered fabrics whose layers have different drying characteristics, e.g. jackets. – For drying individual items, e.g.
Changing the programme sequence Once a programme has started Changing Delay start - changing the programme ^ See "Delay start". You cannot change to another programme once a programme has started (this prevents unintentional alterations). You will need to cancel the current programme before you can select a new one. - cancelling the programme and then selecting a different programme ^ Press the Start/Stop button.
Electronic system lock The system lock prevents your machine being used without your knowledge. You can switch on the system lock if required. The dryer's electronics are then locked. The dryer can still be switched on but a programme cannot be started. – If an attempt is made to start a programme, the indicator light for the Low temperature button will come on and the key symbol 0-§ will appear in the display.
Cleaning and care Emptying the condensed water container Condensate is collected in the condensed water container. Empty the condensed water container after every drying programme. The Empty container indicator light will come on if the maximum level of the condensed water container is reached. The indicator light will go out when the door is opened and closed again. ^ Empty the container. ^ Slide the container back into the dryer. ,Condensed water should not be consumed.
Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening. Clean the filters after each drying programme*. Cleaning them whilst dry Tip: You can also use a vacuum cleaner to remove the fluff. ^ Remove any fluff from the hollow part of the door opening. You could also use a cleaning brush which is available as an optional extra from your Miele Chartered Agent or from Miele, or use a vacuum cleaner.
Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water. ^ Open the door and pull the fluff filter out of the door as described previously. The two filters in the door opening can also be removed if you need to clean them with water. ,Do not replace them if they are damp or wet. Damp or wet filters could cause operational faults.
Cleaning and care Cleaning the condenser unit Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit. Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage. Check the condenser unit at least twice a year. Always check it if the Clean out airways indicator light comes on. If the dryer is used frequently, then check the condenser unit after approx. 100 drying cycles. Clean it if necessary.
Cleaning and care If you cannot see any fluff: ^ Replace the condenser unit (see following page). If you can see some fluff: ^ Clean the condenser unit as described below. Cleaning the condenser unit ^ When rinsing the condenser unit, make sure you position it as shown in the next two illustrations. ^ Pull the condenser unit out of its housing by the handle. Checking the condenser unit ^ Use a shower head or similar to rinse the unit out as shown. ^ Hold the condenser unit up to the light as shown.
Cleaning and care Replacing the condenser unit ^ With the handle facing upwards, push the condenser unit back into position in its housing. ^ Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove. When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove. ^ Then flush the unit through from the front.
Problem solving guide Problem solving guide Most faults can be resolved by yourself. This will save time and money as a call-out charge will apply to customer service visits where the problem could have been rectified as described in these Operating instructions. With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without a call-out being necessary.
Problem solving guide Problem Possible cause Remedy The following flashes at the end of a programme: —œ–...C~–...Cœ˜... The programme has finished but the laundry is still cooling down. You can remove the laundry and spread it out to allow the heat to dissipate, or leave it in the dryer to cool down more. The Clean out airways indicator light comes on. The dryer is not working efficiently or economically. Possible cause: Blockages due to fluff or detergent residues.
Problem solving guide Problem Possible cause Remedy The indicator light Start/Stop flashes slowly and the display is dark. Some programmes won't start anymore. The indicator light for that programme doesn't light up anymore either. The dryer is on standby. This is a normal function and does not indicate a fault. There is no immediate cause. See "Programmable functions". – Switch the dryer off and then on again. – Select the programme that cannot be started.
Problem solving guide An unsatisfactory drying result Problem The laundry is not sufficiently dry. Possible cause The load consisted of different fabrics. Items made of synthetic Synthetic fibres tend to fibres are charged with attract a static charge. static electricity after drying. Remedy – Final drying cycle with Warm air. – Select a different programme next time*.
Problem solving guide Other problems Problem The drying process goes on too long or even switches off. Possible cause In some circumstances, the Clean out airways indicator light still comes on, even though the filters are clean. Clean out airways. Remedy Please check all the possible causes and switch the dryer off and then back on again. Ventilation to and from the dryer may be insufficient (e.g. because it is installed in a small room). This has caused the temperature in the room to rise sharply.
Problem solving guide Problem Possible cause Water leaks from the machine after the condenser unit has been cleaned. – The inner cover of the – Ensure that the condenser unit has not condenser unit is been locked properly positioned correctly and/or the condenser and lock the inner unit has not been cover. positioned correctly. – Check the rubber seals. – There is a build-up of fluff. – Use a cloth to remove any visible fluff from the inside of the condenser unit housing.
Problem solving guide Changing the lamp Disconnect the machine from the mains electricity supply. The lamp specification and maximum wattage are stated on the data plate and on the lamp cover. ^ Open the door. ^ Replace the lamp. You will find the interior lamp cover at the top of the drum aperture. ^ To close the cover, push it upwards and press it on the left and right until you hear it click into position.
After Sales service In the event of any faults which you cannot remedy yourself, please contact – Your Miele Chartered Agent or – Miele (see back cover for address). When contacting Miele, please quote the model and serial numbers, both of which are located on the data plate situated on the right-hand side below the drum aperture.
Installation Front view a Supply cable for electrical connection b Condensed water container c Control panel d Door e Service panel for condenser unit f Four height-adjustable screw feet g External drainage options (e.g. via wash basin, wash basin drain outlet, or gully).
Installation Rear view Building under a continuous worktop / in a kitchen run ,A building-under kit* (Miele accessory, available to order) with a coverplate to replace the appliance's lid is required. It must be fitted by a suitable qualified person to ensure electrical safety. The coverplate included in the building-under kit replaces the appliance's lid. It is necessary to fit the coverplate for electrical safety reasons.
Installation Levelling the machine ,The gap between the base of the dryer and the floor must not be minimised by a plinth or thick-piled carpet as this will prevent a sufficient intake of cold air. Room ventilation The machine must be perfectly level to ensure safe and proper operation. The air which is taken in when the dryer is in operation is blown out of the vents on the front of the machine and warms up the air in the room.
Installation External condensed water outlet General notes When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the machine is installed near a sink, drain outlet etc. so that the condensed water container does not have to be emptied. Drain hose length . . . . . . . . . . . . 1.50 m Maximum delivery head . . . . . . . 1.50 m Maximum drain hose length . . . . 4.
Installation External drainage via a sink or gully ^ See "Front view" illustration. ,If you want to drain the water off into a sink, you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage. Example: Connection to a sink drain outlet The drain hose with non-return valve fitted can be connected directly to a suitable sink drain outlet.
Installation ^ Fit adapter 1 to the sink drain outlet using nut 2. If this nut has a flat disc in it, you should take the disc out first. ^ Attach the end of the hose 4 to adapter 1. ^ Use a screwdriver to tighten hose clip 3 up close to the nut. 1 Adapter 2 Nut 3 Hose clip 4 End of the hose 5 Non-return valve 6 Tumble dryer drain hose 46 ,Non-return valve 5 has to be fitted with the arrow pointing in the direction of flow (i.e. towards the sink). Otherwise water will not drain out of the machine.
Installation Electrical connection Important This tumble dryer is supplied ready for connection to an AC single phase supply. The machine is supplied with a mains cable with moulded plug. The wires in the mains lead are coloured in accordance with the following code: The accesibility of the plug must be always ensured in order to separate the dryer from the mains. The appliance should be connected up only by a qualified electrician, in accordance with national and local safety regulations.
Consumption data Load1 Final spin speed in a domestic washing machine Residual moisture Energy Duration kg rpm % kWh min. CottonsNormal2 7.0 1000 60 3.80 121 Cottons Normal 7.0 7.0 7.0 7.0 1200 1400 1600 1800 53 50 48 43 3.45 3.25 2.90 2.85 110 105 95 93 Cottons Normal + Low temperature 7.0 1000 60 4.10 169 Cottons Hand iron2 7.0 1000 60 3.00 96 Cottons Hand iron 7.0 7.0 7.0 7.0 1200 1400 1600 1800 53 50 48 43 2.65 2.50 2.10 2.05 85 80 70 68 CottonsNormal2 3.
Technical data Height 850 mm Width 595 mm Depth Depth with door open 587 mm 1,062 mm Height for building under Width for building under 820 mm 600 mm Depth for building under Suitable for pushing under a worktop 600 mm Yes Suitable for stacking Weight Yes 51 kg Drum volume Maximum capacity 111 l 7 kg dry weight Capacity of condensed water container Drain hose length approx. 4.2 l Maximum delivery head Maximum drain hose length 1.5 m 4m Length of connection cable 2m 1.
Programmable functions Extending the range of the drying level for the "Cottons" programme The electronics of this dryer ensure a very effective and energy efficient drying process. You can, however, extend the range of the drying level in this programme. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: The option selected will be displayed by a number which will alternate with P. 0 The drying level will be damper.
Programmable functions Extending the drying level for the "Minimum iron" programme The electronics of this dryer ensure a very effective and energy-efficient drying process. You can, however, extend the range of the drying level in this programme. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: The option selected will be displayed by a number which will alternate with P. 0 The drying level will be damper.
Programmable functions Anti-crease setting Helps prevent creasing if laundry is not normally removed immediately after the end of a programme. Anti-crease – is set as a standard setting. You can shorten the time or switch it off completely. – can be used for all programmes, except Woolens handcare. – should always be switched on. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off.
Programmable functions Altering the volume of the buzzer The buzzer has two volumes. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. B Switch the dryer on. The option selected will be displayed by a number which will alternate with P. 0 Default setting.
Programmable functions Extending the drying level for the "Automatic plus" programme The electronics of this dryer ensure a very effective and energy-efficient drying process. You can, however, extend the range of the drying level in this programme. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: The option selected will be displayed by a number which will alternate with P. 0 The drying level will be damper.
Programmable functions Extending the cooling down time The cooling down phase which takes place before the end of a programme can be lengthened if required. This makes the garments easier to handle. The cooling down time is only available for programmes with drying levels. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C.
Programmable functions Standby To save energy, the display goes out after 10 minutes and the indicator light for the Start/Stop button will start flashing slowly. Factory default settings. Not in current programme As in "On". But: The display will not switch off during a programme. Reactivate from Standby Off ^ Turning the programme selector or pressing one of the buttons switches the display back on again. This will not alter a running programme. The display will not switch off during a programme.
Programmable functions Before you begin, first ensure that: – The dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. B Switch the dryer on. Wait until the indicator light for the Start/Stop button lights up constantly. . . The option selected will be displayed by a number which will alternate with P. 0 On I Factory default settings. Not in current programme (The Automatic plus indicator light will also flash once.) C . . .
Programmable functions Memory function The electronics will memorise any Extra options selected for a programme. The duration selected for the timed drying programmes will also be stored in memory. These settings will be selected automatically the next time the programme is chosen. You can either accept these or change them by pressing the appropriate button. The option selected will be displayed by a number which will alternate with P. 0 Default setting. Memory deactivated. I Memory.
Programmable functions Clean out airways indicator Fluff should be removed after drying. The Clean out airways indicator will remind you to Clean the filters when a certain amount of fluff has collected in the filters. You can decide at what level of fluff this reminder should be given. You will have an idea of how often this should be done after a few drying programmes. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off.
Programmable functions Keypad tone An audible tone sounds each time a button is pressed. The option selected will be displayed by a number which will alternate with P. Follow steps (A,B,C ...) to programme and store in memory. 0 Default setting. Keypad tone deactivated. Before you begin, first ensure that: I Keypad tone activated (The Automatic plus indicator light will also flash.) – The dryer is switched off. – The door is closed.
Programmable functions Adjusting the dryer's electronics for very soft water C . . . and then release the Start/Stop button. ,Extremely soft water can affect D Press the Low temperature button ten times. the sensitivity of the control electronics. Important If the dryer is installed in an area with very soft water, you should contact your local water supplier for information and advice regarding water hardness and water conductivity.
Programmable functions Extending the drying level range You can extend the range of the drying levels for many of the programmes: Machine iron plus (drier than Machine iron). Slightly dry (drier than Hand iron). Normal plus (drier than Normal). You can use this programming function only for programmes which allow you to select the drying levels. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off.
Alteration rights reserved/1912 M.-Nr.
