TECHNICAL INFORMATION Touchtronic Clothes Dryers Includes: T1302, T1303, T1322, T1329ci T1403 & T1405 © 2004 Miele
This page intentionally left blank.
Table of Contents GENERAL INFORMATION A. Warning and Safety Instructions 3 B. Modification History 5 C. Technical Data 7 D. Layout of Electrical Components 9 Vented Models 9 Condenser Models 11 010 – Cabinet and Front Panel 1 Technical Data 13 2 Function 15 3 Fault Repair 15 4 Service 15 4.1 Lid – Removal 15 4.2 Plinth (Toekick) – Removal 16 4.3 Front Panel – Removal 16 4.4 Side Panel – Removal 16 4.5 Support Bracket – Removal 17 4.
030 – Drum, Rear Bearing, Sensor and Heater Bank 1 2 Technical Data 23 1.1 Heater Bank (NTC) Temperature Sensor – Resistance Values 25 Function 26 2.1 Residual Moisture Sensor System 26 2.1.1 Residual Moisture Sensing – Drum Assembly 26 2.1.2 Residual Moisture Sensor – Brush Assembly 26 2.2 Drum Bearing 26 2.3 Heating 27 2.3.1 Heater Bank 27 2.3.2 Heater Bank Temperature Sensor 27 2.3.3 Thermostats (Temperature Limiters) 27 3 Fault Repair 27 4 Service 28 4.
040 – Drive and Fan Motor 1 Technical Data 39 2 Function 39 2.1 Main Motor 39 3 Fault Repair 40 4 Service 40 4.1 Drum Drive Belt – Removal 40 4.2 V-Belt – Removal 41 4.3 Intermediate Drive – Removal 41 4.4 Fan Impeller 41 4.5 Drive Motor – Removal 41 050 – Air Circulation and Front Bearing 1 2 3 4 Technical Data 45 1.1 Temperature Sensor (Fan Housing) – Resistance Values 45 Function 46 2.1 Fill Ring 46 2.2 Front Drum Bearing 46 2.3 NTC Temperature Sensor 46 2.
060 – Fascia Panel and Electrical Components 1 Technical Data 62 2 Function 62 2.1 Heater Relays 62 Fault Repair 63 3.1 Fault Summary 63 Service 64 4.1 Programming Mode 64 4.2 Demonstration Mode (Dealer Displays) 66 4.3 Service Mode 67 4.4 Fascia Panel – Removal 72 4.
Touchtronic Clothes Dryers - List of Figures D-1 Layout of Components – Vented Models 9 D-2 Layout of Components – Condenser Models 11 010-1 Cabinet Construction 15 010-2 Support bracket 17 020-1 Removing the outer door panel 21 020-2 Door Lock 22 030-1 Drum Bearing 28 030-2 Drum Rib Hardware 29 030-3 Drum Bearing 30 030-4 Heater Bank Components 31 030-5 Wiring Harness Holder 32 030-6 Access Panel to Heater Bank (Removed) with Heater Bank 33 030-7 Wiring Harness Holder 34 030-8 Res
Touchtronic Clothes Dryers - List of Tables C-1 Overview of Models 7 C-2 Electrical Information 7 030-1 Heater Bank NTC Temperature Sensor Values 25 030-2 Heater Element Activation 26 050-1 Fill Ring NTC Temperature Sensor Values 45 060-1 Fault Summary 63 060-2 Program Mode Positions 65 060-3 Service Mode (1 of 4) 68 060-4 Service Mode (2 of 4 69 060-5 Service Mode (3 of 4) 70 060-6 Service Mode (4 of 4) 71
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information General Information 1
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information A Warning and Safety Instructions 1 General Information Service of this appliance should only be performed by qualified personnel; in accordance with local and national codes. Power should be disconnected from the appliance during service. Unplug the appliance, or the shut off the appropriate circuit breaker.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information B Modification History 04/2004 06/2004 08/2004 Miele USA Miele USA Miele USA 5 Preliminary Information Revised Revised
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information C Technical Data Overview of Models Model Number Capacity 5 Kg T1302 5 Kg T1303 5 Kg T1322C T1329C 5 Kg T1323C T1403 5 Kg 6 Kg T1405 6 Kg Table C-1: Overview of model Additional Information Angled Controls, Vented Flat Controls, Vented Angled Controls, Condenser Fully Integrated Style, Condenser (match for W1119) Flat, Condenser Angled Controls, Vented Angled Controls, Vented, Stainless Steel Finish numbers
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information D Layout of Electrical Components Vented Models 1. (B3/1) 2. (2R30) 3. (M5) 4. (2K1/1) 5. (1K1/1) 6. (Z1) 7. (1N1) 8. (S2) 9. (H3/6) 10. (F1) 11. (A2) 12. (C5) 13.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information D Layout of Electrical Components Condenser Models 1R30 A2 B3/1 B8/7 C5 1F1 / 2F2 H3/6 K1/1 M5 M13 1N1 R1 R2 1R30 2R30 S2 Z1 Door Lock Residual Moisture Sensor Level Switch Capacitor Temperature Limiter (Non Re-settable) Drum Lighting Heating Relay Fan And Drum Drive Motor Condensate Pump (Condenser Dryer Only) Electronic Heater Bank Heater Bank NTC Temperature Sensor (Fan Housing) NTC Temperature Sensor (Heater
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 010 Cabinet and Front Panel 13
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data - To Be Updated 2 Function n/a 3 Fault Repair n/a 4 Service 4.1 Lid - Removal Figure 010-1: Cabinet Construction 1. Remove the screw caps from the side edges of the lid. 2. Loosen the screws about 4 to 5 turns. 3. Press in on the screws, lift the lid from the front and slide it toward the rear. Lift the lid to remove.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.2 Toekick Removal 1. Remove the screw caps, Figure 010-1. 2. Remove the screws. 3. Slide the toekick to the left; pull from the appliance to remove. 4.3 Front Panel - Removal 1. 2. 3. 4. 5. Open the door. Remove the two Door Lock screws. Remove the five screws around the door opening. Remove the toekick (010 4.2). Support the panel from the bottom. Remove the two screws from the bottom corners of the panel. 6.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.5 Support Bracket – Removal 1. Remove the Lid (010 4.1). 2. Remove the Fascia Panel (060 4.4) 3. Disconnect the connectors and pushbutton assembly from the electronic. 4. Remove the rear frame of the Fascia Panel. 5. Disconnect the ground wire. Figure 010-2: Support bracket 6. Remove the four T20 screws, Figure 010-2. 7. Lift upwards to remove the support bracket.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.6 Rear Access Panel - Removal Figure 010-3: Rear Access Panel 1. Remove the 4 retaining screws. 2. Lift the panel from the appliance. Note Remove the Rear Access Panel for access to: The Heater Bank The Heater Bank (NTC) Temperature Sensor Both Temperature Limiters The Rear Drum Bearing Refer to section 030 / Heater Bank for further information.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 020 Door and Door Lock 19
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data 1.1 Door Lock Mechanically operated; via cable and door button. 2 Function n/a 3 Fault Repair n/a 4 Service 4.1 Outer Door Panel – Removal 1. 2. 3. 4. Open the door. Refer to Figure 020-1. Turn the six retainers a quarter turn counterclockwise. Pull the bottom of the outer door panel (while lifting it upward) to remove. Figure 020-1: Removing the outer door panel.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.2 Door Lock – Removal Figure 020-2: Door Lock 1. Open the door. 2. Remove the Front Panel (010 4.3). Note Refer to Figure 020-2. The Door Lock, (1) uses a snap-in style retainer to attach to the drum support housing. 3. Remove the Door Lock from the drum support housing. 4. Disconnect the electrical connection. 5. Release the cable (2).
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 030 Drum, Rear Bearing, Sensor and Heater Bank 23
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data 1.1 Heater Bank (NTC) Temperature Sensor – Resistance Values The heater bank temperature is monitored by the electronic via an NTC (Negative Thermal Coefficient). Temperature Sensor mounted at the top of the Heater Bank Assembly. As the temperature increases – the resistance of the sensor decreases.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1.2 Heater Element – Activation Program Option Selected Heater Element R1 Heater Element R2 Normal N Y Normal Turbo Y Y Normal Full Load Y Y Normal Gentle N Y Table 030-2: Heater Element Activation 2 Function 2.1 Residual Moisture Sensor System The Electronic Residual Moisture Sensor system uses the amount of moisture in the laundry to determine how wet / dry the laundry is. 2.1.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 2.3 Heating 2.3.1 Heater Bank The Heater Bank uses two independently controlled elements (R1 and R2). AC power to elements is controlled by the Electronic via two independent Heater Relays. 2.3.2 Heater Bank Temperature Sensor The temperature of the Heater Bank is monitored by the Electronic via the Temperature Sensor mounted at the top of the Heater Bank Assembly. Refer to 030 1.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4 Service 4.1 Drum - Removal 1. 2. 3. 4. Remove the Front and Side Panel (010 4.3 and 4.4). Remove the Support Bracket (010 4.5) Remove the drum support housing (050 4.1) Release the Drive Belt from the intermediate drive. Figure 030-1: Drum Bearing 5. Refer to Figure 030-1. 6. Block the Bearing using a screwdriver through the opening (2) in the rear panel of the drum. 7.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.2 Drum Rib - Removal 1. 2. 3. 4. 5. Remove the lid (010 4.1) Refer to Figure 030-2, Remove the screws (1). Remove the slip ring screw (2). Reassemble by following these instructions in reverse order. Figure 030-2: Drum Rib Hardware 4.3 Slip Ring - Removal 1. Remove the Drum (030 4.1). 2. Remove the slip ring screws. 3. Turn the drum by hand about 180and remove the screws from the second drum rib. 4.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.4 Drum Bearing - Removal 1. 2. 3. 4. 5. 6. 7. Remove the Rear Access Panel (010 4.6). Refer to Figure 030-3. Remove the 2 screws (2), Slide the cover (1), to the left and remove it. Turn the Drum Bearing clockwise until it is fully visible. Open the bearing shell clips (3), with a small screwdriver (4). Remove the bearing shells to the left and right.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.5 Heater Bank - Removal 1. Remove the Lid (010 4.1) 2. Remove the Rear Access Panel (010 4.6). Figure 030-4: Heater bank, temperature limiters and temperature sensor 3. 4. 5. 6. Note and disconnect the electrical connectors. Refer to Figure 030-5. Release the wiring harness from its holder (1). Remove the rubber grommet (3), with the wiring harness.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 7. Refer to Figure 030-4. Remove the two 7mm screws (4). 8. Remove the heater bank. Figure 030-5: Wiring harness holder Reassembly Note To prevent damage to the wiring, ensure the harness is secured in its holder (Figure 030-5).
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.6 NTC Temperature Sensor - Removal 1. Remove the Rear Access Panel (010 4.6). 1. 2. 3. 4. NTC Temperature Sensor Thermostats (Temperature Limiters) Rubber Grommet Retaining Screw (2) Figure 030-6: Removing the access cover on the rear outer wall of the appliance permits access to the Heater Bank, Thermostats (Temperature Limiters) and Temperature Sensor. 2. Disconnect the connector to the Sensor. 3.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.7 Thermostats (temperature limiters) - Removal 1. 2. 3. 4. 4.8 Remove the Rear Access Panel (010 4.6). Note and disconnect the electrical connections. Remove the screws. Lift the Thermostat(s) from the Heater Bank Assembly. Residual Moisture Sensor – Removal Figure 030-7: Wiring harness holder 1. 2. 3. 4. 5. 6. 7. Remove the Lid (010 4.1) Remove the mount screw.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.9 Residual Moisture Sensor Carbon Brush - Replacement Figure 030-8: Residual Moisture Sensor Brush Replacement 1. Remove the Lid (010 4.1). 2. Refer to Figure 030-8. 3. Lift the Brush Assembly arm and release the two brushes from the arm. 4. Remove the snap on cover (1) from the arm. 5. Install the new brushes on the holder arm. 6. Cut the black wire (5), at the connector to the braided copper wire.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.10 Rear Seal - Removal Figure 030-9: Rear Drum Seal 1. 2. 3. 4. Remove the Drum (030 4.1) Refer to Figure 030-9. Remove the screw (2). Turn the seal and fixing ring (1), counterclockwise to remove it from the holder. Note To properly install the seal, it must be rotated clockwise. Refer to Figure 030-9.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 040 Drive and Fan Motor 37
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data Main Motor 2 Function 2.1 Main Motor 120VAC The Main Motor provides power to the Drum using an intermediate gear / drive belt assembly. The fan impeller(s) (two on condenser dryers – refer to Figure 0401) are mounted on the motor shaft and move the airflow through the appliance. Reversing of the motor is controlled by the Electronic.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 3 Fault Repair n/a 4 Service 4.1 Drum Drive Belt - Removal Figure 040-2: Drives 1. 2. 3. 4. 5. 6. Remove the right Side Panel (010 4.4) Refer to Figure 040-2. Unclip the spring (2). Remove the Support Bracket (010 4.5) Remove the drum support housing. (050 4.1). Remove the drive belt by lifting it from the drum toward the front of the appliance.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.2 V-Belt - Removal 1. 2. 3. 4. 4.3 Remove the right Side Panel (010 4.4) Refer to Figure 040-1. Unclip the tensioning spring (2). Loosen the bolts (1 and 4), and remove the V-belt. Intermediate Drive - Removal 1. Remove the Drum Drive Belt (040 4.1) 2. Remove the V-Belt (040 4.2) 3. Remove the bolts (1 and 4), and remove the intermediate drive. 4.4 Fan Impeller (Vented Models) – Removal 1.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 050 Air Circulation and Front Bearing 43
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data 1.1 1R30 (NTC) Temperature Sensor (Fan Housing) - Resistance Values Temperature (°C) Temperature (°F) Resistance (kΩ) 15 59 18.6 20 68 14.9 25 77 12.0 30 86 9.73 35 95 7.96 40 104 6.55 45 113 5.42 50 122 4.52 55 131 3.78 60 140 3.19 65 149 2.70 70 158 2.29 75 167 1.96 80 176 1.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 2 Function 2.1 Drum Support Housing The Drum Support Housing: Guides the drying air from the drum to the air guide Contains the Front Drum Bearing and Front Seal Secures the Drum Light Assembly Contains a removable access panel to the Fan Impeller (vented models only) Provides a port for 2nd NTC Temperature Sensor. 2.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1. 2. 3. 4. 5.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information Figure 050-2: Drum Support Housing (Condenser Models) 3 Fault Repair 3.1 Drying temperature too high Cause Excessive lint build-up Remedy Clean the filter(s), drum support housing temperature sensor and ducting as necessary.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4 Service 4.1 Drum Support Housing – Removal Caution To prevent damage to the Rear Drum Bearing, ensure the drum is empty and no excess weight is placed on the drum while the drum support housing is uninstalled from the appliance. 1. Remove the Lid (010 4.1). 2. Remove the Fascia Panel (060 4.4) 3. Remove the Electronic (060 4.5). 4. Remove the Fascia Panel frame. 5. Remove the Front Panel (010 4.3) 6.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.2 Front Drum Bearing – Adjustment (does not apply to all models) Figure 050-3: Drum bearing 1. 2. 3. 4. Remove the front panel (010 4.3) Refer to Figure 050-3. Remove the Screws (4) Turn the Eccentric Disc (1) back and forth, while checking the gap between the drum neck and the fill ring. 5. When the gap is the same all around the drum neck, tighten the screws (4). 6.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.3 Light Bulb - Replacement Open the door and locate the bulb on the upper edge of the drum opening. A yellow, plastic tool is provided with the machine to function as an "opener". This tool can also be obtained from the Miele Parts Department. 1. 2. 3. 4. 5. 6. Refer to Figure 050-4 Slide the opener beneath the edge of the bulb cover. Flip down the bulb cover. Turn the bulb to remove. Replace the light bulb.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 055 Condenser System (Condenser Models Only) 53
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information This page intentionally left blank.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data To be updated 2 Function 2.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 2.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 2.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 3 Fault Repair 3.1 Long Drying Time Cause The Condenser Box is clogged blocking the air flow. Remedy Clean the Condenser Box (055 4.1). 3.2 Water Leaking from appliance Cause Fault in Condenser Water Path Remedy Check Condenser Water Path hoses and connections. Check Float Switch for proper operation. Check Drain Pump for proper operation. If drained externally check Drain Hose for proper routing.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information Figure 055-4: Condenser Box Access Panel Figure 055-5: Condenser Door Lock Figure 055-6: Unlocking the Condenser Box Lock 5. Refer to Figure 055-7: Pull out the condenser. 6. Refer to Figure 055-8. Rinse the condenser along the left side with warm water.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information Figure 055-7: Removing the Condenser Box Figure 055-8: Rinsing the left side of the Condenser Box. 7. Refer to Figure 055-9. Rinse the condenser from the front with warm water. 8. Check the condenser for dirt or blockage. Rinse the condenser until clean. 9. Place the condenser lengthwise on a towel to air dry. 10. Re-install into appliance by reversing steps 1 to 5.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 060 Fascia Panel and Electrical Components 61
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 1 Technical Data n/a 2 Function 2.1 Heater Relays Two Heater Relays are controlled by the Electronic. These relays provide the 120VAC supplied to the heater elements. 1K1/1 provides the switching for Heater Element R2 2K1/1 provides the switching for Heater Element R1. Note The contacts within Heater Relay 1K1/1 must be closed in order for Heater Relay 2K1/1 to operate.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 3 Fault Repair 3.1 Fault Summary 1. 2. 3. 4. 5. Turn on the appliance Select a program. Press Start. Allow the appliance to operate for at least two minutes. Observe the display for the following: Fault Signal LED Child Lock LED flashes Cause Buzzer (if turned on) Fault Code – – Lock function activated. Turn off the Child Lock Feature (see 3.2) – Condensate container float switch.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4 Service 4.1 Programming Mode Summary Initial requirements - Turn off the machine. - Close the door. Note Once you begin the access procedure, it must be completed within 10 seconds. Accessing 1. Press and hold the Start button while turning the unit on. 2. Release the Start button as soon as the Anti-crease/Finish LED lights up, 3. Immediately press and release the Start button 4 times. 4.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information Program Setting Flashing Buzzer LED Long – – Program Function Programmable Option(s) Flashing Drying LED Short 1 2 Short Reset all programmable functions to standard settings: Press the Start button.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.2 Demonstration Mode (Dealer Displays) Initial requirements - Turn off the unit. - Close the door. Note Once you begin the access procedure, it must be completed within 10 seconds. Accessing 1. Press and hold the Start Button while turning on the unit 2. Release the Start Button as soon as the Start LED lights, 3. Immediately press and hold the Start Button, until the Start LED flashes.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.3 Service Mode Initial requirements - Turn off the unit. - Close the door. Note Once you begin the access procedure, it must be completed within 10 seconds. Accessing 1. Press and hold the Start Button while turning the unit on. 2. Release the Start Button As soon as the Anti-crease/Finish LED lights. 3. Immediately press and release the Start Button 2 times. 4.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information Test Step Service Level 2 – Activation and Navigation The Test Step is indicated by a flashing Drying LED. While in Service Level 2 press the Start Button to begin the first Function Test. Press the Start Button to advance to the next Function Test. . Turn the unit off to quit the test mode.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information SERVICE LEVEL Flashing Buzzer LED TEST STEP SERVICE FUNCTION Flashing Rhythm Drying LED Long – Function Tested/ Machine Response Short 1 Drive/Fan motor. Drum turns as follows: counterclockwise for 10 seconds, a 2.5 second pause, clockwise for 10 seconds, a 2.5 second pause, etc… Heating 1 and drive. Drum turns counterclockwise for 10 minutes, a 2.5 second pause, clockwise for 10 seconds, a 2.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information SERVICE LEVEL Flashing Rhythm Of Buzzer LED TEST STEP SERVICE FUNCTION Flashing Rhythm Of Drying LED Long Function Tested/Machine Response Short Residual moisture sensing circuit, high resistance check. Ensure the clip leads or the wires used in the low resistance check are removed; and no laundry is present in the drum. – 5 The appliance will operate for about 30 seconds.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information SERVICE LEVEL Flashing Rhythm Of Buzzer LED 3 4 TEST STEP SERVICE FUNCTION Flashing Rhythm Of Drying LED Function Tested/Machine Response Long Short – 1 – 2 Float Switch Test (condenser models). Buzzer operates when the float switch is activated. Digital sensor test Operating hours Door Switch Test - Buzzer operates when the door is closed.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.4 Fascia Panel - Removal Figure 060-1: Fascia Panel - Removal 1. Use a Miele Opener (or a small screwdriver) and press the front section downwards. 2. Tilt the panel from the top outward. Note To ensure the springs do not get lost remove them from the lower groove for the panel.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information 4.5 Electronic / Controls - Service Position Note The electronic can be positioned into the retaining slots on the sides of opening during service procedures. 1. 2. 3. 4. Remove the Fascia Panel (060 4.4) Refer to Figure 060-2. Remove the two screws. Carefully pull the control module forward. Figure 060-2: Electronic retaining screws 5. Refer to Figure 060-3 6.
T1302, T1303, T1322, T1329ci, T1323c, T1403 and T1405 Clothes Dryers Technical Information Figure 060-3: Button Assembly 7. Refer to Figure 060-4. 8. Slide the control module into the retaining slots on either side of the fascia panel opening.
This page intentionally left blank
