Descriptive Technical Documentation - Model-dependent - DTD no. 512-6161 Model(s): PW 6161, PW 6201 24.03.2005, DE_en This information should not be duplicated or passed on without Miele approval. All rights reserved.
This information should not be duplicated or passed on without Miele approval. All rights reserved. 24.03.
Descriptive Technical Documentation 1 DTD no. 512-6161 Contents General Information A Warning and Safety Instructions B Modification History C Technical Data D Layout of Electrical Components Function Groups 090 100 Door 4 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 090-1 4.1 4.2 Door cap removal / fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door removal / fitting . . . . . . . . . . . . . . . . . . . . . . . .
Descriptive Technical Documentation DTD no. 512-6161 2 150 2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130-2 2.1 2.2 2.3 Water paths, flow rates, combination for programming . . . . . . . . Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Protective functions - Level monitoring . . . . . . . . . . . . . . . . . . . . . 130-2 130-6 130-7 Casing 1 4 Technical Data . . . . . . . . . . . . . . . .
DTD no. 512-6161 Descriptive Technical Documentation A-1 A Warning and Safety Instructions 1 General information These machines should not be installed or operated in any area where there is a risk of explosion. x Note Service and repair work should only be carried out by suitably qualified persons in accordance with all appropriate local and national safety regulations. Before any service work is commenced, the machine must be disconnected from the mains.
A-2 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
Descriptive Technical Documentation B-1 DTD no. 512-6161 B 24.03.2005, DE_en Modification History When? Who? What? 29.11.2004 Norbert Polenz Initial compilation This information should not be duplicated or passed on without Miele approval. All rights reserved.
B-2 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
Descriptive Technical Documentation C-1 DTD no. 512-6161 C Technical Data Technical data – PW 6161, version June 2004 x PW 6161 Gas 6) Heating Electric Capacity (dry laundry) 16 kg / Fill ratio 1 : 10 Highpressure steam (indirect) Highpressure steam (direct) Lowpressure steam (direct) Packaging dimensions Width - Normal/Sea [mm] 1060/.. ../.. 1060/.. 1060/.. 1060/.. Depth - Normal/Sea [mm] 1186/.. ../.. 1186/.. 1186/.. 1186/.. Height - Normal/ Sea [mm] 1606/.. ../.. 1606/..
Descriptive Technical Documentation DTD no. 512-6161 C-2 PW 6161 Heating Electric 3N AC 380 - 415 V 50 - 60 Hz [mm2] 5 x 4.0 3 AC 220 - 240 V 50 - 60 Hz [mm2] 4 x 10.0 3N AC 380 - 415 V 50 Hz [mm2] 3 AC 440 V 50 - 60 Hz [mm2] Gas 6) Highpressure steam (indirect) Highpressure steam (direct) Lowpressure steam (direct) 5 x 1.5 5) 5 x 1.5 5 x 1.5 5 x 1.5 5 x 4.0 Water supply Cold 2 x Pressure hose DN 10 (mm dia.) with threaded union 3/4", 1.
Descriptive Technical Documentation C-3 DTD no. 512-6161 PW 6161 Heating Electric Gas 6) Highpressure steam (indirect) Highpressure steam (direct) Lowpressure steam (direct) G-force Wash 0.67 Pre-spin Spin Residual moisture in accordance with DIN 119024) 500 [%] Approx. 46 after 7 min final spin (2 min at 1150 rpm) Flow pressure requirement Min. [kPa] 100 Max. [kPa] 1000 Largest removable part Removal/ Installation time, approx. Suds container: Dia. 782 mm x 568 mm [h] 3.0 / 4.
Descriptive Technical Documentation DTD no. 512-6161 C-4 Technical data – PW 6201 (20 kg machine), version June 2004 x PW 6201 Gas6) Heating Electric Capacity (dry laundry) 20 kg / Fill ratio 1: 10 Highpressure steam (indirect) Highpressure steam (direct) Lowpressure steam (direct) Packaging dimensions Width - Normal/Sea [mm] 1060/.. ../.. 1060/.. 1060/.. 1060/.. Depth - Normal/Sea [mm] 1296/.. ../.. 1296/.. 1296/.. 1296/.. Height - Normal/ Sea [mm] 1606/.. ../.. 1606/.. 1606/..
Descriptive Technical Documentation C-5 DTD no. 512-6161 PW 6201 Heating Electric 3 AC 440 V 50 - 60 Hz [mm2] Gas6) Highpressure steam (indirect) Highpressure steam (direct) Lowpressure steam (direct) 5 x 6.0 Water supply Cold 2 x Pressure hose DN 10 (mm dia.) with threaded union 3/4", 1.5 m long Cold hard Hot ≤ 70°C 1 x Pressure hose DN 10 (mm dia.) with threaded union 3/4", 1.5 m long Intake rate, max.
Descriptive Technical Documentation DTD no. 512-6161 C-6 PW 6201 Heating Electric Gas6) Highpressure steam (indirect) Highpressure steam (direct) Lowpressure steam (direct) Flow pressure requirement Min. [kPa] 100 Max. [kPa] 1000 Largest removable part Suds container: Dia. 782 mm x 678 mm Removal/ Installation time, approx. [h] 3.0 / 4.0 Material Plinth Galvanised sheet steel Drum Stainless steel 1.4016 Suds container Stainless steel 1.4301 Front casing Stainless steel 1.
Descriptive Technical Documentation C-7 DTD no. 512-6161 Consumption data – PW 6161 (16 kg machine), version June 2004 x PW 6161 Heating Electric Temperature increase rate, low water level [°C/min] Approx. consumption/wash cycle in accordance with DIN 11902 Cold water Gas3) Highpressure steam (indirect)1) Highpressure steam (direct) Lowpressure steam (direct) 3.0 1.8 8 10 0.
Descriptive Technical Documentation DTD no. 512-6161 C-8 PW 6161 Heating Electric 60°C programme with cool down Duration Gas3) Highpressure steam (indirect)1) Highpressure steam (direct) Lowpressure steam (direct) [min] 30°C programme2) - Heating [kWh] Energy consumption Other electrical parts [kWh] 1.
Descriptive Technical Documentation C-9 DTD no. 512-6161 Consumption data – PW 6201 (20 kg machine), version June 2004 x PW 6201 Heating Electric Temperature increase rate, low water level [°C/min] Approx. consumption/wash cycle in accordance with DIN 11902 Cold water Gas3) Highpressure steam (indirect)1) Highpressure steam (direct) Lowpressure steam (direct) 3.0 1.8 8 10 0.
Descriptive Technical Documentation DTD no.
DTD no. 512-6161 D Descriptive Technical Documentation D-1 Layout of Electrical Components Layout for EL version (with electric heating) x Layout 1 A1 A2 B1/1 B1/14 F3 F7 F9 24.03.2005, DE_en Selection-display module (BAE) EW 230 Door lock Level switch - Water intake Boiling dry protection Winding protection – Drive motor Fine-wire fuse Safety cut-out This information should not be duplicated or passed on without Miele approval. All rights reserved.
Descriptive Technical Documentation DTD no.
Descriptive Technical Documentation D-3 DTD no. 512-6161 GAS models, additional components x Layout 2 1B1/13 2B1/13 B2/13 C6 F10 K1/19 M6 Y57 24.03.2005, DE_en Level switch - Pump pressure Level switch - Pump pressure Temperature regulator - Exhaust Capacitor - Circulation pump Ignition monitor Relay/Contactor - Circulation pump Motor - Circulation pump Valve - Gas solenoid valve This information should not be duplicated or passed on without Miele approval. All rights reserved.
Descriptive Technical Documentation DTD no. 512-6161 D-4 D models (with steam heating), additional components x Layout 3 Y25 Valve - Heating (steam) This information should not be duplicated or passed on without Miele approval. All rights reserved. 24.03.
DTD no. 512-6161 090 Door 4 Service 4.1 Door cap removal / fitting Descriptive Technical Documentation 090-1 A Remove the front panel, see Front panel removal, 150 4.7. A Remove the 9 fixing screws. A Remove the door cap. A Reassemble by following these instructions in reverse order. 4.2 Door removal / fitting A Open the door wide. A Remove the 2 screws from the top and bottom of the hinge. x Note E-shaped spacers are positioned under each 2 screws for adjusting the door.
090-2 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
Descriptive Technical Documentation 100-1 DTD no. 512-6161 100 Fascia panel 1 Technical Data x Control component Abbreviation Electronic module Selection-display module BAE EW 230 Control-power module SLT ELP 230 Multifunction module MFM ELZ 230 Distribution connection Frequency converter EV 230 EFU EFU 230 Table 1: Control system parts 24.03.2005, DE_en This information should not be duplicated or passed on without Miele approval. All rights reserved.
Descriptive Technical Documentation DTD no. 512-6161 100-2 2 Function 2.1 Profitronic M washing x Fig. 1: Profitronic M control 1 2 3 4 5 6 7 8 9 10 Multifunction buttons 1 to 6 Display (64 lines x 220 columns) Start button Multifunction selector (outer ring) Chip card reader slot Emergency Off switch Switch – Off Switch – On OK button (centre of multifunction selector switch) Optical interface This information should not be duplicated or passed on without Miele approval. All rights reserved. 24.
Descriptive Technical Documentation 100-3 DTD no. 512-6161 The Profitronic M unit controls and regulates processes in commercial washerextractors. It can save up to a maximum of 199 programmes in 999 programme positions. The Profitronic M unit has a multifunction selector switch (jogshuttle action) with OK button, a graphic display (64 lines x 220 columns), a start button and 6 multifunction buttons. There are three main operating levels.
Descriptive Technical Documentation DTD no. 512-6161 100-4 Main components of control unit: – Selection-display module (BAE) EW 230, to operate the control unit, display messages, indicate control state, enable backup copies of saved data and programmes to be made, and for communication with other electronic modules in the machine. – Control-power module (SLT) ELP 230, to control and regulate processes in the machine, save programmes and for communication with other electronic modules in the machine.
Descriptive Technical Documentation 100-5 DTD no. 512-6161 2.2 Wash programme header Structure and arrangement of programme header: The programme header describes the general structure of a wash programme and defines certain fixed parameters. Example 1: Should the heating be switched off during a programme via the Peak-load cut-out input of the machine? Programming options: Yes or No. Example 2: What is the charge for this programme when using a payment system? Answer: e.g. 1.25 currency units.
Descriptive Technical Documentation DTD no. 512-6161 100-6 Item number in table Item description Options Details 11 Weigh No It is not possible to enter a weight before the start of the programme. The control operates with the rated load for the machine, 100 Table 4. Default factory setting: No. Manual The operator weighs the dry laundry then enters the established weight manually in the machine before the start of the programme.
Descriptive Technical Documentation 100-7 DTD no. 512-6161 24.03.2005, DE_en Item number in table Item description Options Details 14 Fill type Water height in mm Fixes which type of monitoring is used by the control to register the water level when filling the machine. The setting options available later in the wash programme depend on the type of fill programmed here. Default factory setting: Water height in mm, “mm” stands for millimeters of water column (mm wc).
Descriptive Technical Documentation DTD no. 512-6161 100-8 Item number in table Item description Options Details 17 Peak load Yes / No Peak-load cut-out: High load peaks in electrical systems can result in particularly high energy costs. With major installations, the peak-load cut-out feature avoids these extra charges for load peaks. A monitoring system registers current consumption and when this is too high, a cut-out signal is produced.
Descriptive Technical Documentation 100-9 DTD no. 512-6161 Model, programme and maximum load table x Model PW 6101 PW 6131 PW 6161 PW 6201 Drum volume 100 l 130 l 160 l 200 l Cottons 90°C 10.0 kg 13.0 kg 16.0 kg 20.0 kg Cottons 60°C 10.0 kg 13.0 kg 16.0 kg 20.0 kg Cottons intensive 60°C 10.0 kg 13.0 kg 16.0 kg 20.0 kg Cottons 30°C 10.0 kg 13.0 kg 16.0 kg 20.0 kg Cottons intensive 30°C 10.0 kg 13.0 kg 16.0 kg 20.0 kg Short programme 10.0 kg 13.0 kg 16.0 kg 20.
Descriptive Technical Documentation DTD no. 512-6161 100-10 Block programming – Profitronic M washing control x No. Programme step Basic setting Setting options Notes 0 Block name 20 blank spaces All available alphanumeric and special characters For naming block 1. Maximum name length 20 characters, e.g. Pre-wash.
Descriptive Technical Documentation 100-11 DTD no. 512-6161 No.
Descriptive Technical Documentation DTD no. 512-6161 100-12 2.4 Minimum heating level The machine has a protection system to prevent damage due to dry heating (heater elements not under water). If the programmer selects a temperature greater than cold in a block, the control automatically raises the water level if necessary.
Descriptive Technical Documentation 100-13 DTD no. 512-6161 2.6 Service mode (service level) – General information The service mode can be accessed in two different ways: Either manually directly at the machine via the controls on the selection-display module (BAE), or by using the optical interface to link up with a PC running Service Dept. software. The machine has a special service mode which can be used, for example, by the Service Dept. technician to operate and test the machine.
Descriptive Technical Documentation DTD no. 512-6161 100-14 There are 2 service programme sub-divisions: x Service mode (service level) 1 Service programme 1 Test manually 2 Test automatically Table 10: Service programme divisions Test manually has 10 further sub-divisions: etc. etc. To simplify orientation among the numerous control possibilities, this BTD uses the numbering shown in the above tables, see 100 Table 9, 100 Table 10.
Descriptive Technical Documentation 100-15 DTD no. 512-6161 2.7 Data security in control-power module and selection-display module After a break in the mains supply, the control can register if saved data (settings, operating data, operating faults, machine history and service settings) in the control-power module (SLT) is different to that saved in the selection-display module (BAE). Reasons for this could be, e.g., exchange of a sub-assembly or a defective sub-assembly.
Descriptive Technical Documentation DTD no. 512-6161 100-16 2.
Descriptive Technical Documentation 100-17 DTD no. 512-6161 3 Fault Repair 3.1 Fault code summary Cause See fault code table. Fault indications in operating level x Machine area Indication Notes “Warning” symbol PRESSURE SENSOR FAULT! Call the Service Department if restart does not work. During a programme in operation the control registers impermissible values at the analog pressure sensor input. If the fault is still registered after a restart, no programme can be started.
Descriptive Technical Documentation DTD no. 512-6161 100-18 Machine area Indication Notes “Warning” symbol HEATING SYSTEM FAULT! Switch off the main switch. Call the Service Department. Control registers that both heating dry protection contactors (1 and 2) have cut-out. Both heating contactor contacts have fused together. Machine is filled via 3 inlet valves to maximum level and the programme in operation is stopped.
Descriptive Technical Documentation 100-19 DTD no. 512-6161 4 Service 4.1 Programming mode Initial requirements A A wash programme must not be in operation. A The machine must not be in the service mode. Accessing A Switch on the machine. A Wait until the Welcome start screen is displayed. A Press the language selection button (under the flag symbol) to access the main menu. A Select Operating level and confirm with the OK button. A Enter the password and confirm with the OK button.
Descriptive Technical Documentation DTD no. 512-6161 100-20 Item number in table Item description Options Details 4 ID No. (Identification number) All numbers The supervisor/programmer only can read this field. The control automatically enters the software version number of the control under which the wash programme was created.
Descriptive Technical Documentation 100-21 DTD no. 512-6161 24.03.2005, DE_en Item number in table Item description Options Details 14 Fill type Water height in mm Fixes which type of monitoring is used by the control to register the water level when filling the machine. The setting options available later in the wash programme depend on the type of fill programmed here. Default factory setting: Water height in mm, “mm” stands for millimeters of water column (mm wc).
Descriptive Technical Documentation DTD no. 512-6161 100-22 Item number in table Item description Options Details 17 Peak load Yes / No Peak-load cut-out: High load peaks in electrical systems can result in particularly high energy costs. With major installations, the peak-load cut-out feature avoids these extra charges for load peaks. A monitoring system registers current consumption and when this is too high, a cut-out signal is produced.
Descriptive Technical Documentation 100-23 DTD no. 512-6161 Block structure x No. Programme step Basic setting Setting options Notes 0 Block name 20 blank spaces All available alphanumeric and special characters For naming block 1. Maximum name length 20 characters, e.g. Pre-wash.
Descriptive Technical Documentation DTD no. 512-6161 100-24 No. Programme step Basic setting 9 Level 1 Load/Liquor ratio: 1: 0.
Descriptive Technical Documentation 100-25 DTD no. 512-6161 Save and quit A The appropriate settings can be saved via the save button (disk symbol). A To quit the programming mode, switch off the machine or step back to the appropriate level via the menus. Quit (without saving) A Switch off the machine. 4.2 Service mode summary Initial requirements A Close the door. A Switch off the machine. Accessing A Press and hold the W Start button. A Switch the machine on via the mains switch.
Descriptive Technical Documentation DTD no. 512-6161 100-26 Acknowledgement indicator Successful accessing of the service mode is indicated by rapid flashing (5 Hz) of the W Start button illuminated switch surround. Options The Service mode is divided into 4 different parts: x Service mode (service level) 1 Service programme 2 Service information 3 Service settings1) 4 Delete display message1) Table 17: Service mode sub-divisions 1) Only visible under the following circumstances: 1.
Descriptive Technical Documentation 100-27 DTD no. 512-6161 x Note All service programmes are limited to an overriding safety time of 30 min. System analyse has the following sub-divisions: x Service mode (service level) 1 Service programme 1 Test manually 1 System analyse Designation Display Explanation – E.g.: Analysis in progress Checks all modules and their sensors to see if they are present.
Descriptive Technical Documentation DTD no. 512-6161 100-28 Control-power module has the following sub-divisions: x Service mode (service level) 1 Service programme 1 Test manually 2 Control-power module (component) Designation Display Explanation Machine type: E.g. PW 6101 Electric heating Display of model registered by the control with type of heating ID Number E.g.
Descriptive Technical Documentation 100-29 DTD no. 512-6161 Selection-display module has the following sub-divisions: x Service mode (service level) 1 Service programme 1 Test manually 3 Selection-display module (control element) Designation Display Explanation ID Number E.g. 123456789 Display of EW 230 control module ID number registered by the control Display E.g.: Contrast: 3.
Descriptive Technical Documentation DTD no. 512-6161 100-30 When the desired item has been selected via the multifunction selector (jogshuttle switch), press the OK button. The selected service programme then starts immediately and can be stopped when the Back button is pressed.
Descriptive Technical Documentation 100-31 DTD no. 512-6161 Operating data module has the following sub-divisions (control checks operating data module and memory card): x Service mode (service level) 1 Service programme 1 Test manually 9 Operating data module Designation Display Explanation – E.g. Operating data module and “Start” symbol above a multifunction button Starts analysis of operating data module. Result or fault indication is then displayed.
Descriptive Technical Documentation DTD no. 512-6161 100-32 MPG (German medical product law) module has no function or test points. x Service mode (service level) 1 Service programme 1 Test manually 12 MPG module Designation Display Explanation ... ... ... Table 29: MPG (German medical product law) module Language module has no function or test points. x Service mode (service level) 1 Service programme 1 Test manually 13 Language module Designation Display Explanation ... ... ...
Descriptive Technical Documentation 100-33 DTD no.
Descriptive Technical Documentation DTD no.
Descriptive Technical Documentation 100-35 DTD no. 512-6161 When the desired item has been selected via the multifunction selector (jogshuttle switch), press the OK button. The selected service programme then starts immediately and can be stopped when the Back button is pressed. After the machine has been repaired, the service technician can delete the fault memory. Delete operating faults has the following sub-division: x Service mode (service level) 2 Service information 3 Delete operating faults No.
Descriptive Technical Documentation DTD no.
Descriptive Technical Documentation 100-37 DTD no.
Descriptive Technical Documentation DTD no. 512-6161 100-38 4.3 Selection-display module (BAE) removal / fitting A Remove the machine lid, see Lid removal / fitting, 150 4.4. A Loosen 1 retaining screw/nut (viewed from the rear, at the upper left of the back of the fascia panel). A Slide the module locking bar to the left (viewed from the rear) as far as possible. The Module is now released. A At the front, tilt the top edge of the module 5 mm outwards away from the machine.
Descriptive Technical Documentation 100-39 DTD no. 512-6161 4.5 Fascia panel removal / fitting A Remove the machine lid, see Lid removal / fitting, 150 4.4. A Remove the selection-display module, see Selection-display module (BAE) removal / fitting, 100 4.3. A Remove the detergent dispenser cover flap, see Detergent dispenser cover flap removal / fitting, 100 4.4. A Remove 2 screws on either side of the dispenser flap holder.
100-40 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
Descriptive Technical Documentation 130-1 DTD no. 512-6161 130 Water intake 1 Technical Data Flow pressure and flow rates. x Permitted flow pressure [bar] Valve type 1 to 10 1 to 10 3/4”, triple 3/4”, triple Flow rate - Valve block 1 [l/min] 10 - Flow rate - Valve block 2 [l/min] 16 - Flow rate - Valve block 3 [l/min] 16 - Liquid dispensing [l/min] - 5.5 Table 1: Water inlet data 24.03.2005, DE_en This information should not be duplicated or passed on without Miele approval.
Descriptive Technical Documentation DTD no. 512-6161 130-2 2 Function 2.1 Water paths, flow rates, combination for programming x Fig. 1: Water path summary This information should not be duplicated or passed on without Miele approval. All rights reserved. 24.03.
DTD no.
Descriptive Technical Documentation DTD no. 512-6161 130-4 x Fig.
Descriptive Technical Documentation 130-5 DTD no. 512-6161 x Fig. 3: Valves in valve blocks on machine rear panel The flow quantities for the valve blocks are limited due to the interaction when two or more valves in a valve block are activated. If more water is required in a certain time period, the activation of different valves in different blocks should be programmed. x Valve block Quantity limitation at input Valve block designation 1, see 130 Fig. 1, Pos.
Descriptive Technical Documentation DTD no. 512-6161 130-6 2.2 Valves Inlet valve summary - PW 6101, PW 6131, PW 6161, PW 6201 x Designation on wiring diagram Description Detergent dispenser compartment Symbol Designation in software / documentation 1Y5 Valve - Water inlet - Cold, hard, direct – – KH, HAW 2Y5 Valve - Water inlet - Cold, hard, direct – – KH, HAW 1Y6 Valve - Water inlet - Cold, pre-wash, max.
Descriptive Technical Documentation 130-7 DTD no. 512-6161 2.3 Protective functions - Level monitoring The control monitors the maximum water level in all operating states. The programmer can only program the following maximum levels: x Model Maximum programmable level [mm] PW 6101 350 PW 6131 350 PW 6161 350 PW 6201 350 Table 5: Maximum programmable water levels - PW 6101 to PW 6201 If the software registers an overflow, e.g.
130-8 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
DTD no. 512-6161 150 Casing 1 Technical Data Descriptive Technical Documentation 150-1 x Material - Front panel Stainless steel 1.4016 Material - Lid, side panels Galvanised sheet steel, powder coated, blue Material - Rear panel Galvanised sheet steel Table 1 24.03.2005, DE_en This information should not be duplicated or passed on without Miele approval. All rights reserved.
Descriptive Technical Documentation DTD no. 512-6161 150-2 4 Service 4.1 Transport information A The machine should only be transported without a pallet if the front and rear panel have been removed, see Front panel removal, 150 4.7 und Rear panel bottom part removal / fitting, 150 4.6.
DTD no. 512-6161 Descriptive Technical Documentation 150-3 x Fig. 2: Rear transport struts A Remove 3 screws from each rear red transport strut. A Remove the transport struts. A Take care to retain the transport struts with their associated screws and pass them to the operator for safe keeping in case the machine needs to be relocated in the future. A Reassemble the machine. 4.3 Transport strut fitting A Remove the front and rear panels, see Front panel removal, 150 4.
Descriptive Technical Documentation DTD no. 512-6161 150-4 x Fig. 3: Front transport struts A Fit the front transport struts and secure each one with 3 screws. x Fig. 4: Rear transport struts A Fit the rear transport struts and secure each one with 3 screws. A Reassemble the machine. This information should not be duplicated or passed on without Miele approval. All rights reserved. 24.03.
Descriptive Technical Documentation 150-5 DTD no. 512-6161 4.4 Lid removal / fitting A Remove 1 screw from each side of the lid at the top of the machine. A Lift the lid slightly at the front and disconnect its earth connection. A Slide the lid slightly to the rear to release its conical retainer guides from the rear panel. A Remove the lid upwards. A Reassemble by following these instructions in reverse order. 4.
Descriptive Technical Documentation DTD no. 512-6161 150-6 4.7 Front panel removal A Remove 1 screw on each side of the front panel from the underneath of the bottom edge. A Pull the bottom edge outwards slightly so releasing it from its conical retainer guides half way up the front. A While it is slanted, lower the front panel to release it from its top retainers on the fascia panel. Remove the front panel downwards. 4.8 Front panel fitting A Tilt the top edge of the front panel to the rear.
DTD no. 512-6161 160 Documents 1 Technical Data Descriptive Technical Documentation 160-1 Wiring diagram, wiring diagram legend, switching plan, multifunction module, operating instructions, programming instructions for Profitronic M washing 24.03.2005, DE_en This information should not be duplicated or passed on without Miele approval. All rights reserved.
160-2 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
DTD no. 512-6161 Descriptive Technical Documentation 500-1 500 Testing, special documents 1 Technical Data Log book for testing in accordance with accident prevention legislation. 24.03.2005, DE_en This information should not be duplicated or passed on without Miele approval. All rights reserved.
500-2 This information should not be duplicated or passed on without Miele approval. All rights reserved. Descriptive Technical Documentation DTD no. 512-6161 24.03.
