Installation plan Commercial dryer PDR 928/528 G Gas heated To avoid the risk of accidents or damage to the machine, it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
Contents Installation notes ............................................................................................................. Installation requirements ................................................................................................... Electrical connection ......................................................................................................... Gas connection .........................................................................................................
Installation notes Installation requirements The tumble dryer must only be installed and commissioned by Miele Customer Service Department or an authorised dealer. The tumble dryer must be installed in accordance with all relevant regulations and standards. The dryer must only be operated in a room that has sufficient ventilation and which is frost-free. Electrical connection The electrical connection must be established by a qualified electrician.
Installation notes Gas connection The gas connection must only be carried out by a registered installation technician in accordance with the applicable national regulations (see installation instructions). The use of a gas socket is not permitted at the specified heater rating as the flow rate is too low. The gas heating is configured at the factory in line with the gas specifications on the sticker on the rear of the appliance.
PDR 928/528, gas heated Dimensions 1206 >20 642 Ø 630 918 1640 1019 67 38 45 ° 20 765 914 710 Ø 520 1200 1640 >20 1600 < 1200 1206 18 0° 1019 914 1600 Measurements in millimeters PDR 928/528 G / Gas heated 5
PDR 928/528, gas heated Installation 875 325 96 XCI EL 1700 G G 125 520 200 G 19 ZL 520 305 125 ~350 ZL AL 179 31 305 1700 64 EL AL "Y" "Y" 160 161 ZL ZL EL 2x AL "Z" "Z" ~ 50 150 AL Measurements in millimeters Electrical connection EL G Gas connection AL Vented ZL Air intake XCI 6 XCI-/Connector-Box (option) PDR 928/528 G / Gas heated
PDR 928/528, gas heated 1640 1640 Set up (Standard/Concrete platform) 20 >50 20 BS >55 680 55 545 >55 1090 545 ~ 48 B-B B >50 ~ 55 B Ø 10 B BS >1200 1200 A-A B 920 B BS ~ 48 ~ 55 1600 A 920 913 B B BS >1200 1600 A B 680 1090 55 Ø 10 Measurements in millimeters B Fittings/drill hole BS Concrete platform PDR 928/528 G / Gas heated 7
Technical data Voltage variants/electrical data Standard connection Voltage 1N AC 230 V Frequency 50 Hz Total connected load 1.2 kW Fuse rating (on-site) 10 A Connection cable, min. cross-section 3×1.5 mm² Cable gland M20 Gas connection Nominal heat rating 30 kW ½" Machine-side connection according to ISO 7-1 To connect the gas appliance, a corrugated metal hose line made of stainless steel according to DIN 3384 must be used. The shut-off device must be provided on-site.
Technical data Overall machine depth 1019 mm Niche width 1550 mm Recommended distance between front of machine and the wall 1600 mm Minimum distance between rear edge of lid and the wall 500 mm Packaging width 1390 mm Packaging height 1766 mm Packaging depth 1108 mm Maximum gross volume 2719.9 l Maximum gross weight 260.9 kg Maximum net weight 246.3 kg Max.
Technical data Optional extras Concrete platform (on site) Minimum width 1200 mm Recommended height 100 mm Minimum height 50 mm Minimum depth 1100 mm Quality and density of concrete must comply with load. Concrete platform must be firmly secured to floor.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road Abingdon, Oxon, OX14 1TW Professional Sales, Tel: 0845 365 6608 E-mail: professional@miele.co.uk Internet: www.miele.co.uk/professional Australia Miele Australia Pty. Ltd. ACN 005 635 398, ABN 96 005 635 398 1 Gilbert Park Drive, Knoxfield, VIC 3180 Tel: 1300 731 411 Internet: www.miele.com.au/professional E-mail: sales@miele-professional.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No.
