Installation Plan
PWM 908 en-US
= standard, = optional, + = only on request, - not available
8 11 282 580/04
Technical data
PWM 908 DV
PWM 908 DP
Drum volume
gal (l) (ft3)
19.3 (73) (2.58)
19.3 (73) (2.58)
Capacity
lb (kg)
17.6 (8.0)
17.6 (8.0)
Door opening diameter
inch (mm)
11 13/16" (300)
11 13/16" (300)
Max. spin speed
rpm
1,500
1,500
g-factor
613
613
Residual moisture (standard load according to DIN 60456)
%
48
48
Electrical connection (EL)
Standard voltage for CDN & USA
-
2 AC 208-240 V
Frequency
Hz
-
60
Total rated load
kW
-
4.0 – 5.2
Fuse rating
A
-
2 x 30
Power cord min. cross-section
-
3 x AWG10
Wire with plug NEMA L6-30
-
Wire length
inch (mm)
-
78 3/4" 2000
Non-standard voltage MAR 208-240 (Marine)
-
2 AC 208-240 V
Frequency
Hz
-
60
Total rated load
kW
-
4.0 – 5.2
Fuse rating
A
-
2 x 30
Power cord min. cross-section
-
3 x AWG10
Wire with plug NEMA L6-30
-
Wire length
inch (mm)
-
78 3/4" (2,000)
Cold water (KW)
Permissible water flow pressure
PSI (kPa)
1.45 – 14.5 (100 – 1,000)
1.45 – 14.5 (100 – 1,000)
Required flow rate (cold water connection only)
gal/min (l/min)
2.9 (11)
2.9 (11)
Required flow rate (with additional hot water connection)
gal/min (l/min)
2.6 (10)
2.6 (10)
Average water consumption (60°C standard programme)
gal/h (l/h)
10.5 (40)
10.5 (40)
Connection to be provided on site, external thread according to DIN 44991 (flat seal)
Inches
¾"
¾"
Connection hose ½" with ¾" threaded union
Connection hose length
inch (mm)
61 (1,550)
61 (1,550)
Hot water (WW)
Max. water intake temperature
°F (°C)
158 (70)
158 (70)
Permissible water flow pressure
PSI (kPa)
1.45 – 14.5 (100 – 1,000)
1.45 – 14.5 (100 – 1,000)
Required flow rate
gal/min (l/min)
2.9 (11)
2.9 (11)
Average water consumption (60°C standard programme)
gal/h (l/h)
3.4 (13)
3.4 (13)
Connection to be provided on site, external thread according to DIN 44991 (flat seal)
Inches
¾"
¾"
Connection hose ½" with ¾" threaded union
Connection hose length
inch (mm)
61 (1,550)
61 (1,550)
Drain valve (DV)
Connector (ext. diameter)
inch (mm)
3 (75) /DN70
-
Max. drainage temperature
°F (°C)
194 (90)
Max. transient flow rate
gal/min (l/min)
16 (62)
-
Drain pump (DP)
Hose connection (external diameter)
inch (mm)
-
7/8 (22) /DN22
Max. drainage temperature
°F (°C)
-
194 (90)
On-site hose sleeve (int. diameter x length)
inch (mm)
-
22 x 30
Max. transient flow rate
gal/min (l/min)
-
6.8 (26)
Max. delivery head (from lower edge of machine)
inch (mm)
-
39 3/8" (1000)
Drain hose DN 22 with connector (supplied as standard)
-
Connection hose length
inch (mm)
-
59 1/16" (1500)
Potential equalization (PA)
Machine connection (separate kit required)
XCI box LG interface