Operating and Installation Instructions Ceramic Cooktop KM 5656 en - US, CA To prevent accidents and machine damage, read the Operating Manual before installation or use. M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cooktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Burner controls and displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Timer controls and display . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS READ THE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE COOKTOP WARNING This appliance is only intended for residential cooking. The manufacturer cannot be held responsible for damage or injury caused by improper use or for uses other than those for which this appliance is intended.
IMPORTANT SAFETY INSTRUCTIONS Injury prevention Children should not be left unattended in an area where the cooktop is in use. Never allow children to sit or stand on any part of the cooktop. Caution: Do not store items of interest to children in cabinets above the cooktop. Children climbing on the cooktop to reach these items could be injured. Use the Safety Lock to prevent children from turning on the cooking zones or changing the settings. See "Safety lock" for more information.
IMPORTANT SAFETY INSTRUCTIONS Never leave a cooktop unattended at high settings or when cooking with oil or fat. Overheated oil could ignite. Always heat oil slowly, monitoring it as it heats. To prevent burns and breathing difficulty, allow the cooktop to cool before cleaning. Some cleaners may produce toxic fumes if applied to a hot surface. Do not use water on grease fires. Smother or use a dry chemical or foam-type extinguisher on any fire or flame.
IMPORTANT SAFETY INSTRUCTIONS Damage protection Never place hot pots or pans over the touch controls, this may damage the electronics. Do not drop anything on the ceramic surface of the cooktop. Even lightweight objects may cause damage. Do not use pots or pans with pronounced edges or ridges on the ceramic cooktop. These could scratch the cooktop permanently. See "Selecting cookware" for more information. Grains of salt and sand can cause scratches.
IMPORTANT SAFETY INSTRUCTIONS Appliance safety Further safety notes In the event of any damage to the appliance, it must be turned off immediately and disconnected from the main power supply. Call Miele’s Technical Service Department. Do not use the appliance until it has been repaired. Ensure power is not supplied to the appliance until repair work is completed. Make certain that the power cords of small appliances do not come in contact with the cooktop.
Guide to the appliance Cooktop ac Single burners b Extended burner d Variable burner e Burner controls and displays f Cooktop on or active indicator g Cooktop ON/OFF touch control h Safety lock touch control i Safety lock indicator j Timer controls and display 8
Guide to the appliance Burner controls and displays a Touch controls To select the power level (touch individually). To activate the second heating circle of the variable burner (touch simultaneously). b Burner On/Off touch control c Display: = 0 = 1 to 9 = # = F = A = po etc. = so etc.
Guide to the appliance Timer controls and display a Timer display b Touch controls for setting the time c Timer touch control To turn the timer on/off, to toggle between timer functions and to select a burner for auto turn off. d Auto turn off indicator, e.g. rear right burner Burner data Burner KM 5656 diameter in inches / cm Power in watts y 4 3 / 4" / 8 1/ 4" (12 / 21 cm) 1100 / 2400 w 5 11/16" (14.5 cm) 11 11 7 1200 x 6 /16" / 6 /16" x 10 /16" (17 cm / 17 x 26.
Before using for the first time Clean the cooktop Touch controls Before using for the first time, clean and dry the cooktop with a soft damp cloth. This cooktop has electronic controls activated by the touch of a finger. There is a separate touch control for each burner. A tone sounds to indicate that contact has been made with a control. Heat the cooktop The metal components of the cooktop have a protective coating which may give off a slight odor the first time the appliance is heated.
Resetting the touch controls Automatic reset Manual reset To ensure the cooktop functions properly the touch controls will automatically reset: ^ Make sure no direct light (sun or artificial) beams onto the cooktop. The surrounding area of the cooktop should not be completely shaded or brightly lit. – when the cooktop is connected to the electrical supply, – if there is an interruption to the electrical supply, and – during use in response to changing light conditions.
Use Turning on the cooktop ^ Touch the s On/Off cooktop touch control. A horizontal bar – will appear in each of the burner displays and the On/Off indicator will light. If no setting is chosen within a few seconds the cooktop will turn itself off as a safety measure. Turning on a burner ^ Touch the s On/Off touch control for the desired burner. The respective burner display shows 0. ^ Select a power level between 1 and 9 by pressing the - or + control.
Use Settings Use for Power level* Melting butter, chocolate, etc.
Use Auto heat When auto heat has been activated the burner turns on automatically at the highest setting and then changes to the continued power level which was selected. The heat-up time depends on which continued power level has been chosen (see table). Power level Heat up time (minutes : seconds) 1 1 : 20 2 2 : 45 3 4 : 05 4 5 : 30 If a high continued power level was selected, a shorter heat-up time is necessary.
Use Turning off a burner Residual heat indicator ^ Touch the s On/Off touch control for the desired burner. The display shows - for a few seconds. If the burner is still hot the residual heat indicator will show. Turning off the cooktop ^ Touch the s On/Off control for the cooktop. All burners are turned off. If any burners are still hot the residual heat indicator will show in the respective display. The bars in the residual heat indicator go out one after another as the burner cools.
Selecting cookware Following these tips will allow you to make the most of your ceramic cooktop. The cooking surface The ceramic cooktop is made of an extremely hard and durable material. The surface is scratch resistant, not scratch proof. Avoid using cookware with ridged bottoms. Ridged pots with dirty or chipped enamel bottoms may scratch the cooktop if they are pulled across the ceramic surface. Make sure the cooktop and pot bottoms are clean before cooking.
Selecting cookware Copper bottom and aluminum pans may leave a residue on the cooktop in the form of metallic lines. This is normal. These lines can be removed using a non-abrasive ceramic cooktop cleaner or a shielded scraper blade. Be sure to clean the cooktop after each use. Each time this residue is allowed to melt it becomes harder to remove and may mar the appearance of the cooktop. Let the cooktop cool before cleaning.
Timer The cooktop has a timer which can be used to: – time any activity in the kitchen. – automatically turn off one (any) burner. The functions above can also be used simultaneously. Quick Guide: Turn on Touch m Set with - set from 99 to 00 minutes with + set from 00 to 99 minutes Toggle between the functions Touch m Reset back to 00 touch - and + simultaneously Setting the timer The timer can be set with the cooktop either turned on or off. It can be set from 1 to 99 minutes.
Timer Setting the timer to turn off a burner automatically To use this feature a power level must be selected for the desired burner. ^ Turn the desired burner on and select a power level. ^ Touch the m timer sensor. The display will show 00. ^ Touch the m timer sensor again. An indicator will light in the time display. ^ If multiple burners are turned on, press and hold the m timer sensor until the indicator of the desired burner lights, e.g. rear right.
Safety features Child Safety Lock Keep children away from the cooktop for their own safety. The cooktop has a Child Safety Lock to prevent children from turning on the burners or changing the settings. To deactivate the Child Safety Lock ^ Press and hold the $ Child Safety Lock control until the indicator goes out. In the case of a power failure the Child Safety Lock will be deactivated. The Child Safety Lock can be activated while the cooktop is on or off.
Safety features Stop and Go To activate Stop and Go Stop and Go is a feature which reduces the power of all turned on burners. The cooktop can be left for a short time without supervision and the danger of boilovers. ^ Press and hold the $ Lock control until you hear two audible signals in quick succession. Do not touch the $ Lock control too long or the Safety Lock will be activated. The safety lock indicator will flash. The power for the activated burners is now reduced to power level 1.
Safety features Safety cut-out feature Covered touch controls The cooktop is on too long The cooktop has a safety cut-out feature in case it is not turned off after use. If a burner is turned on for an unusually long period of time (see table), and the power levels are not adjusted, the cooktop will turn itself off automatically and the residual heat indicator will light.
Safety features Overheating protection Each burner is equipped with a temperature limiter. This limiter turns off the heating elements in the burner before the ceramic surface becomes too hot. Once the ceramic surface has cooled to a safe temperature the heating elements will automatically turn back on. The overheating protection may be activated by: – turning on a burner without putting a pan on it. – heating an empty pan. – an uneven pan not sitting evenly on the burner.
Cooktop Settings The following default cooktop settings of the cooktop can be reprogrammed if needed: Auto-heat settings Default power Demo mode Power level range Residual heat indicator Safety lock Stop and go Timer function Timer start setting Timer tone Tone for touch controls If you would like to reprogram the settings of your cooktop, please contact Miele for assistance.
Cleaning and Care Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. Pressurized steam could cause permanent damage to the surface and to components for which the manufacturer cannot accept responsibility. Do not use any sharp pointed objects which could damage the seal between the ceramic surface, the surrounding frame and the countertop.
Frequently asked questions ,Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. The manufacturer cannot be held responsible for unauthorized work. What if the cooktop or the burners cannot be turned on? Possible fault Fix The Safety Lock is activated. Deactivate the safety lock. See "Safety lock". The main fuse has blown. Check the main fuse.
Frequently asked questions What if one or more residual heat indicators flash? Possible fault Fix There was a power failure during use. The burners are turned off. Turn the cooktop on as usual. The residual heat indicators were lit while the programming mode, e.g. Safety Lock, Stop and Go, was selected. The residual heat indicators will flash for about 45 minutes after leaving the programming mode. The cooktop can be used as usual.
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the cooktop. This information is visible on the silver data plate supplied with the cooktop.
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire. The cabinetry and venting hood should be installed first to prevent damage to the cooktop.
IMPORTANT SAFETY INSTRUCTIONS To eliminate the risk of burns or fire by reaching over heated surfaces, cabinet storage space above the cooktop should be avoided. If cabinet storage is necessary, the risk can be reduced by installing a venting hood to project horizontally a minimum of 5" beyond the bottom of the cabinets. Because of the heat radiated it is not recommend to install the cooktop above a drawer. It should be installed above a cabinet base unit with a dummy drawer front.
Installation Cooktops flush with the countertop a Wall b Wall covering c Back splash strip d Countertop e Countertop cut-out f 2" (50 mm) minimum distance 34 Frame/Facet cooktops
Installation Installation dimensions a Spring clips b Installation height c Installation height power supply line d Front e Flexible stainless steel hose Length = 3’ 11" (1200mm) 35
Installation Cut out ^ Make the countertop cut-out following the dimensions given in the illustration. Remember to maintain a minimum distance of 2" (50 mm) between the rear wall and the right or left side. See also "IMPORTANT SAFETY INSTRUCTIONS". ^ Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture. The materials used must be heat resistant.
Installation Installing the spring clips Wood or corian countertops Granite countertops ^ Fix the supplied spring clips at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the 1/8" x 1" (3.5 x 25 mm) screws supplied. ^ For granite countertops, the spring clips must be placed in position and secured with strong, double-sided adhesive tape. ^ In addition, coat the edges of the spring clips with silicone sealant.
Installation Installing the cooktop Wooden countertop ^ Feed the power cord down through the cut-out and connect the appliance to the power supply. ^ Position the cooktop on the spring clips, a. ^ Then with a hand on each side of the cooktop press down evenly on the edges until it clicks into position. When doing so make sure that the cooktop seal sits tightly on the countertop to ensure it is sealed correctly. The cooktop can now only be removed with a special tool.
Installation Sealing The cooktop must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the cooktop provides a sufficient enough seal. If the cooktop is sealed into position, the countertop or the appliance may be damaged if the cooktop needs to be removed for maintenance or service.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible.
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Alterations rights reserved / 1207 For the most updated manual see the Miele website. M.-Nr.
