Installation Instructions KM 400 Electric Cooktop KM 402 / KM 403 Fryer KM 408-1 Contact Grill KM 410 / KM 411 Electric Barbecue To prevent accidents and machine damage, read these instructions before installation or use. UV M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety distance above the appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 KM 400 / KM 408-1 . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. Installation The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire. recommended To prevent appliance damage, the cabinetry and venting hood should be installed first.
IMPORTANT SAFETY INSTRUCTIONS Cooktops should not be installed above a dishwasher, washer, dryer, freezer or refrigerator. The high temperatures radiated downwards from the cooktops could damage these appliances. This equipment has not been designed for maritime use or for use in mobile installations such as aircraft or recreational vehicles. However, under certain circumstances it may be possible for an installation in these applications.
Appliance dimensions KM 400 / KM 408-1 a Clamps b Please allow an additional 3/4" (18 mm) depth below the cooktop for clearance of the power cord.
Appliance dimensions KM 402 / KM 403 a Clamps 7
Appliance dimensions KM 410 / KM 411 a Clamps 8
Installation Cutting out the countertop Installing one or multiple appliances: Cut out the countertop using the dimensions listed in the following table. Number of cooktops All Miele combisets have the same length and width. Make sure that there is enough room beneath the countertop to allow for the depth of the various appliances. When installing a KM 402 / KM 403 or KM 410 / KM 411 remember to allow clearance for the drain valve that will be located in the cabinet beneath the appliances.
Installation Laying out the support bars and clamps a Clamps b Support bars This illustration shows the layout for 3 combisets, their respective support bars, b, and the 14 spring clamps, a, required for correct installation. If more than 3 combisets are being installed, add an additional 11 3/8" (288 mm) to the overall width of the cut out for each extra combiset, or use the table on the preceding page. 10 c Slight gap between support bar and countertop.
Installation Securing the support bars Securing the spring clamps d c Wood or Corian countertops Wood or Corian countertops ^ Arrange the bars, b, as shown in the illustration ^ Place the spring clamps, a, as shown in the illustration. ^ Drill 1/16" (1.5 mm) pilot holes through the brackets and secure them using the supplied screws. ^ Drill two 1/16" (1.5 mm) pilot holes for each clamp and secure using the supplied screws.
Installation Locking the appliance into place Make sure the cooktops are aligned correctly before setting them into the countertop. Once the spring clamps are engaged, a special tool is required to release the cooktop from the clamps. ^ Guide the power cord through the cut out and connect the appliance to the electrical supply. ^ Position the cooktop over the cut out. With a hand on each side, above the clamps, a, press the cooktop down, locking it into the spring clamps.
Installation Important The cooktop must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the cooktop provides a sufficient seal for the countertop. If the cooktop is sealed into position, the countertop or the appliance may be damaged if the cooktop needs to be removed for maintenance or service.
Electrical connection ,WARNING: Disconnect the appliance from the main power supply before servicing. To reduce the risk of electric shock, make sure that the appliance is properly grounded after installation. To guarantee the electrical safety of this appliance; continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met. If there is any doubt, have the electrical system of the house checked by a qualified electrician.
Alterations rights reserved / 0705 M.-Nr.
