Installation instructions Integrated dishwasher To prevent accidents and machine damage, read these instructions before installation or use, M-Nr, 05 620 662
Contents iMPORTANT SAFETY INSTRUCTmONS ................................. 3 mNSTRUCTmONSmMPORTANTES SUR LA SECURmTE ..................... 5 Caring for the environment .......................................... Disposal of the packing material ....................................... Disposal of an old machine ........................................... 7 7 7 Opening the door .................................................. Opening the door without a panel in place ...............................
iMPORTANT SAFETY mnstallation Insta!lation, maintenance If there is any doubt concerning installation contact the Technical and repair work shou,d bebyaM,e,eService authorized service technician. Work by unqualified persons could be a hazard and may void the warranty. Department. USA 1-800-999- !360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.
iMPORTANT SAFETY iNSTRUCTiONS E_ectrica_ safety ChHd safety Before installation, make sure the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubL To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met.
iNSTRUCTiONS JMPORTANTES Installation SUR LA SECURJTE Si vous avez des doutes au sujet de I'installation, contactez le D6partement du service technique Miele, L'insta,ation etlestravaux de r6paration etd'entretien doivent Ure effectu6s par un technicien de service autoris6 Miele, Les travaux effectues par des personnes non qualifi6es, pourraient _tre dangereux et faire annuler la garantie, Cet equipernent n'a pas 6t6 con_u pour usage maritime ou pour les installations mobiles te!les que les rouIottes o
iNSTRUCTiONS S6curite JMPORTANTES 61ectrique Avant I'installation, s'assurer que la SUR LA SECUFHTE Securite des enfants S'assurer de disposer de bus les tension et fr6quence 6num6r6es emba,ages dep ast que, sacs etc sur la plaque signal6tique correspondent b,la source d'61ectricit6 de la residence. Ces donnees doivent correspondre afin d'6viter de vous blesser et d'endommager I'appareik Consulter un electricien qualifi6 si vous avez des doutes.
Caring Disposa_ materia_ of the packing The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocatio!! Disposa_ for the environment of an o_d machine Old appliances may contain materials that can be recycled.
Opening the door Opening the door without pane[ in place a [] Gently pull on the upper portion of the mounting bracket until the door latch releases (small arrow), Without place: the mounting bracket in [] Grip the T shaped opening with a finger and pull the door open,
Product G 600 Series Dishwashers Full size models G 643 - G 663 and Cut-out Removing Dimensions the Jeg extensions The black leg extensions can be removed to reduce the machine height to 32 1/4"- 33" (819-838 ram) (see Inset). A = B = Black leg extension (removable) White leg (must be installed on machine). [] After removing the black leg extensions, screw the white legs onto the dishwasher. i Contact the Miele Technical Service re necessary. Department for the appropriate legs. .........
Product and Cut-out G 800 Series Dimensions Dishwashers Full size models G 843 - G 863 greater than 35" (889 ram), extended ill legs (part# 02 702 601) are necessary.
Installation 1.
installation [] Center the steam deflector in the opening for the dishwasher and align with the lower front edge of the cou ntertop, Note: For rounded countertops it may be necessary to pull the steam deflector closer to the counter's edge so the optic reflector will be visible, [] Secure the deflector in place using the supplied nails, [] Wipe of any excess silicone with a solution of liquid dish soap and warm water, 12 [] Press the optic indicator reflector in place,
installation Stone or marble countertops: The steam deflector is not required for countertops made of solid, waterproof material. But it is needed for determining the correct position of the optic indicator reflector. [] Remove the black plastic reflector holder and the tape holding it in place from the steam deflector. [] Line up the D_acK reflector no_oer w_m the tracing ana Dress nrc olace [] With the reflector cut out left and ffontward, align the steam deflector with the front edge of the counter.
installation 2. Install brackets the mounting To ensure stability this dishwasher should be securely attached to the countertop with the two mounting brackets included, 3.
installation 4, Install the dishwasher under the countertop The dishwasher must be installed so that the water and electricity supplies can be accessed through an adiacent cabinet. The supplies must not be located behind the machine. [] Make certain that there are no rough edges that could damage the power cord or hoses. If metal cabinets are used, place the supplied rubber grommet around the edge of the opening before passing the cable through.
installation 5. Leve_ the _egs [] The rear leveling legs can be adiusted with a T20 Torx screwdriver by turning the screws at the front of the slide skis, To raise the machine turn clockwise, To lower the machine turn counter clockwise, Several turns may be needed to set the correct heighL Do not use a power screwdriver.
installation 6. mnstaH the custom door PaneJ Dimensions: pane_ Width: ............... A custom door panel must be installed on the dishwasher before it can be Range of panel heiqht: safely operated. A single large panel or a two piece panel separated at the drawer line can be used. G 800 series .......... ................... 27 1/2"- 30 1/4" (699 - 768 ram) G 600 series .......... ...................
installation The door panel is attached to the dishwasher using the mounting bracket that comes secured to the front of the unit, To remove the bracket: [] Open the door 2- 4" (5 - 10 cm), [] Loosen the bracket retaining screw (black arrow) located on each side of the machine door, [] Pull the bracket up until the upper section of the bracket disengages from the Iocator pins, then remove the bracket, 18
Installation Install the bracket on the rea_ of the custom doo_ panel [] Make sure the dishwasher is leve!, [] Measure the distance X between the round hole in the machine outer door panel (shown in inset) and the lower edge of the adioining cabinet door.
Installation [] Place the bracket on the door panel so the notches, _, cross the previously drawn centerline, and the bottom of the bracket lines up with the horizontal X line. [] Mark and drill pilot holes for the 3 Ii screws using a /32 (2,5 ram) drill bit. [] Attach the bracket to the back of the panel, using the 14 screws provided. The top four pair of holes, only need to be secured once per pair. 2O [] Double check the location of the bracket before mounting the panel to the dishwasher.
installation Attach the front panel to the dishwasher [] Open the door 2- 4" (5 - 10 cm), The "T" shaped hanger behind the door handle should fit easily into its respective hole, [] Place the lower mounting clips into the slots of the dishwasher door as shown in the illustration, [] Seat the U shaped slots of the upper bracket onto their respective Iocator pins, [] Press the panel against the door and slide down so that all the brackets catch, 21
installation 7. Adjust panel and secure the front Once installed, the panel can be raised or lowered up to 1/lfi" (2 ram) to match the cabinet lines. Adiust one side of the door panel at a time using a T20 Torx screwdriver. [] If the upper screws on the edge of the door are not loose, loosen them slightly. [] The panel can be raised or lowered by turning the lower screw on each side of the dishwasher door. To raise the panel turn clockwise. To lower the panel turn counterclockwise.
installation 8. Secure the dishwasher [] Open the dishwasher door. seal located at the top, outer edge of the dishwasher is tight against the bottom of the countertop. Do not drill any additional holes through the wash cabinet. If in doubt on how to secure the dishwasher, please call Miele's Technical Service Department.
installation For openings exactly 23 s/,, ,s (60 ore) wide: _x_f ''''¸''''''_''¸''_''''''''''''''¸' ........................... _........................................................ !i!l only be used for securing the z_The side m°unting h°les sh°uld dishwasher if the opening is exactly 23 5/8 (60 cm) wide. Use of this method on larger i openings can damage the machine ii and cause leaks. Be careful not to screw into an adjacent appliance.
installation 9. Adjust the door springs [] Open the dishwasher door halfway, If the door remains in this position when released, the springs are adiusted correctly, If the door drops, the tension on the springs needs to be increased, If it closes on its own, the tension on the springs need to be decreased, [] To adiust the door springs use a T20 Torx or a small slotted screwdriver and turn the screw located behind the door in the upper front strip, on the left hand side of the dishwasher.
installation 10. Make the p_umbing connections An air gap is built into the water inlet system to prevent potable water from mixing with waste water. The dishwasher can heat its own water to the temperatures required by the wash program. This allows the option of connecting the machine to either a hot or cold water source. [] For lowest energy consumption connect the dishwasher to a cold water source.
installation Existing pJumbing: ' me standard "__ copper p_umo_ng for s dishwasher a_reao', exIsfs wt_r a ,OfT Dresslon fitting aria awe as pictured I i_i_d_ji_i_[_[__ z_WARNING - Elcetrical Hazard Do not cut the intake hose. If the hose is cut, the dishwasher will not work. There will be a water leak and [] Cut the :_/s"copper tubing after the valve. [] Install the 3/ _sII compression to "_/j4`' MHT (Male Hose Thread) adapter (supplied with the machine), as illustrated.
installation Drainage system specifications: O The machine comes equipped with: - A5 fL long (1.5 m) flexible drain hose with an internal diameter of 7/,8. (22 mm). Drain hose extensions can be ordered from Miele's Technical Service Department. - A built-in swivel connector allowing the drain hose to be routed in any direction. - A built-in mechanical non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher.
installation Venting the drainage system If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor, the drain must be vented, Otherwise the water inside the dishwasher may siphon out during the wash program, To vent the drain: [] Open the dishwasher door and remove the lower basket, Additional note Since all Miele dishwashers are equipped with an odor trap and nonreturn valve, the drain hose can be connected directly to the drain pipe as
installation 11. Make the e_ectrica_ connection GROUNDmNG mNSTRUCTmONS Specifications The dishwasher comes equipped with a 4 ft (1.2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. Rated load: .......... In the event of a malfunction or break down, grounding will reduce the risk of electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug.
Installation Power outlet Permanent The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located, An opening through the partition between the compartments of 1 1/2"(3 to 4 cm) can be made to allow the plug to pass through, For hard wiring, the power cord must be disconnected from the terminal box located at the lower left front of the dishwasher, behind the toekick and service panel, Pass the permanent power supply
JnstaJJation 12. Test the unit Once the dishwasher is level and secured it should be tested. [] Remove all packing and literature from inside the unit. The yellow Child Safety Lock key hung on the upper basket must be removed before operating the dishwasher. If not removed, the key could become lodged in the circulation pump. [] Make sure the triple filter system in the base of the wash cabinet is locked in place. Turn the handle clockwise to lock. [] Close the soap dispenser.
Installation 13.
G 800 Series dishwasher [] Insert the mounting bracket with the flange pointing toward the center of the machine, [] Insert the mounting bracket with the flange pointing toward the outside of the machine, [] Push the mounting brackets in as far as possible by releasing the tension on the spring clip (see illustration), [] Push the mounting brackets in as far as possible by releasing the tension on the spring clip (see illustration), 34
installation The included toekick will fit without modification if the machine is set to its maximum height and the toekick is recessed as far as possible (4"/10 cm). If the machine height is less than maximum, or if the toekick is not recessed 4" (10 cm), the toekick must be shortened. [] Screw the toekick onto the installed brackets, with the cutting lines towards the top, and pull out evenly and slowly until it aligns with the toekick of the adioining cabinets.
installation [] Carefully open the dishwasher door until it hits the toekick. [] Using the front lower edge of the door panel as a guide, draw a line across the toekick. [] Unscrew and remove the toekick. [] If one of the cutting lines is close to the line iust drawn, score the front of the toekick, and snap off the excess, otherwise, trim the toekick along the line using a saw. [] Screw the toekick back onto the brackets, with the cut edge at the bottom.
When contacting the Technical Service, please quote the model and seria| number of your appiianceo MieJe, Jnc, MieUe Limited Nationam Headquarters 9 Independence Way Princeton, NJ 08540 Phone: 800o843o7231 609=419=9898 Fax: 609=419=4298 www.mieUeusa.com National Headquarters 55G East Beaver Creek Road Richmond Hill, ON L4B 1E5 Phone: 800=643=5381 905=707=1t71 Fax: 905=707=0177 www.mieUe.ca info@mieUe.ca (general enquiries) professionaU@mieUe.
