Installation instructions for eye-level dishwashers It is essential to read the operating and installation instructions before installing or using the machine, to avoid the risk of accident or damage to the machine. G M.-Nr.
These installation instructions apply to several different dishwasher models. Model numbers in this booklet refer to the model designation specified on the data plate on the machine (and not the description on the control panel). The data plate is located at the top of the door when open. The model numbers quoted refer only to the basic model number, e.g. the G 349SC is described as the G 349 in this booklet.
Contents Building in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. Measurements for building in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Fitting the control facia panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Fitting the panel front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.
Building in This dishwasher is intended to be built into a tall unit. The following are needed: – A facia panel (GW...), – A dishwasher front, consisting of a panel front and plinth facia (GFH 55), – A building in frame (GER 60). The facia panel and the front panel must be fitted before the dishwasher is built into the tall unit. ,To ensure stability this dish- washer must only be built into a tall unit. It must not be set up as a freestanding machine.
Building in 1. Measurements for building in Normally connection to water is sited near the dishwasher, for example in the area under the sink. A Miele sink base unit already has a suitable cut out for installation. If the base unit has no cut-out and if there is no opening through the plinth area for connections, one must be made. The following conditions must be met: – The recess floor must be capable of bearing a load of at least 80 kg. – The housing unit must be at least 550 mm deep.
Building in 2. Fitting the control facia panel The dishwasher must not be used until the control panel has been correctly fitted. Dishwashers with selector dial (G 349) ^ Attach cap a to push button switch. ^ Push the ventilation grille b into position so that the slats on the grille are facing downwards. ^ Place the facia panel c in position and use the six screws d to secure in place through from the inside of the door. ^ Attach selector e.
Building in Dishwashers with programme selector buttons (G 396) ^ Attach cap a to push button switch. ^ Push the ventilation grille b into position so that the slats on the grille are facing downwards. ^ Place the facia panel c in position and use the six screws d to secure in place through from the inside of the door. ^ Insert the programme selector buttons e and function buttons f.
Building in 3. Fitting the panel front 4. Adjusting the dishwasher height ^ Hang the panel front into the slits on the machine door outer panel a. ^ Adjust the machine feet evenly until the height of the dishwasher just reaches the height of the recess. ^ Tighten fixing screws b on both sides of the door outer panel. ^ Plug openings b using the plastic stoppers supplied. 8 ^ Press the slides with the ratchet at the rear under the screw feet.
Building in 5. Fitting the drain hose The drain hose is in the wash cabinet. The connection stub is located low down on the rear side of the dishwasher. ^ Connect the drain hose using the hose clip supplied. The connection stub can be turned. The hose can be laid to the right or left without needing to loosen the hose clip.
Building in 6.
Building in Position Description Quantity 1 Counter sunk screws 4 x 15 3 2 Top frame strip 1 3 Spacer for unit wall thickness 16 mm 4 4 Spacer for unit wall thickness 19 mm 4 5 Side frame strips 2 6 Foot holds 2 7 Stoppers 2 8 Bottom frame strip 1 9 Spacer bar 1 10 Plinth facia 1 11 Plinth facia retainer 2 12 Rubber rings 2 13 Protective sheet 1 14 Wood screws 4 x 20 2 15 Wood screws 4 x 15 6 16 Wood screws 4 x 30 with sleeve 2 not illustrated Edge protect
Building in 7. Fitting the building-in frame and installing the dishwasher Apply moisture protector ^ Seal the cracks between the side walls and the recess floor and any unprotected cut surfaces with the silicone sealant provided. Screw the foot holds and edge protector in place ^ Secure the foot holds (6) with two wood screws each 4 x 15 (15) to the side walls of the housing unit. The distance from the front edge of the unit to the front edge of the foot holds must measure 450 mm .
Building in ^ Place side frame strips (5) into the housing unit A. ^ Push the top frame strip (2) into position B. ^ Screw the side frame strips to the bottom of the side walls using the 4 x 20 (14) wood screws. ^ Screw the top frame strip to the recess ceiling using the 4 x 15 (1) countersunk screws.
Building in Fitting the dishwasher into the housing unit Aligning the dishwasher ^ Shut the dishwasher door. ^ Screw the machine feet out until the dishwasher is touching the recess ceiling. ^ Lay the hoses and cable into the unit and down through the installation duct. ^ Push the dishwasher into the unit recess. The back feet should rest in the openings of the footholds. ,Ensure the hoses and cable do not get kinked or squashed.
Building in To secure the dishwasher ^ Open the dishwasher door. ^ Adjust the front screw feet manually or with a flat blade screwdriver. ^ Align the dishwasher: - the gap between the panel front and the side frame strips must match, and - the facia control panel and the panel front must sit flush with the building in frame. ^ Screw a 4 x 15 (15) wood screw from below into the holes in the right and left hand side of the upper strip. ^ Remove the cover caps from the side openings, left and right.
Building in To fix the protective sheet ^ Remove the backing from the adhesive strip. ^ Put the cover caps back in the openings. Use the extra ones supplied if necessary. ^ Stick the protective sheet (13) on the plinth along the edge below the screws.
Building in To fit the bottom frame strip To fit the plinth facia Recess height 876 mm: ^ Fit stoppers (7) into the "Key-holes" in the side frame strips A. ^ Push the bottom frame strip (8) over the lower ends of the side frame strips (5). ^ Pull the handle for the plinth facia (11) forward and push outward until it engages B. Recess height 882 mm: ^ First push the spacer bar (9) from below onto the bottom frame strip.
Building in 8. Adjusting the door springs ^ Half open the dishwasher door. The door springs are correctly adjusted when the door remains stationary when left open at 45 °. The door springs are easier to adjust when the door is only half open than when it is fully open. If the door drops down, then the door springs need to be tightened. If it closes then the springs need to be loosened. The adjusting screw is located in the upper front strip at the left hand side of the dishwasher.
Electrical connection ,Please follow the installation instructions carefully. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance while installation work is being carried out. This dishwasher is supplied with a mains cable and moulded plug ready for connection to an a.c.
Electrical connection The wires in the mains lead are coloured in accordance with the following code: Green/yellow = earth Blue = neutral Brown = live If the colours of the wires in the mains lead of this appliance do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol z or coloured green, or green and yell
Plumbing Connection to the water inlet ,Water in the dishwasher must not be used as drinking water. – The dishwasher may be connected to a cold or hot water supply, max. 60 °C. When connected to a hot water supply all programme stages which would otherwise be carried out with cold water (pre-wash and interim rinse) as well as the Pre-wash programme will be carried out with hot water. – The programme "Energy save" (without heater) needs connection to a hot water supply with a temperature of at least 45 °C.
Plumbing Drainage Venting the drainage system – The machine drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the machine via the drain hose. ^ Open the dishwasher door fully. – The dishwasher is supplied with an approx. 2.25 m long flexible drain hose with an internal diameter of 22 mm. – The drain hose can be extended using a connection piece and an extra drain hose, (up to max. 4 metres).
Technical data Dishwasher model G 349 G 396 Height 84.2 cm (adjustable + 5.0 cm) 84.2 cm (adjustable + 5.0 cm) Height of building in recess 87.5 - 89.5 cm 87.5 - 89.5 cm Width 54.7 cm 54.7 cm Width of building in recess 56.2 - 56.8 cm 56.2 - 56.8 cm Depth 57 cm 57 cm Depth with open door 120.5 cm 120.5 cm Weight integrated model integrated model SC # approx. 53 kg approx. 54.5 kg approx. 55 kg approx. 56.
Alteration rights reserved (MNovoplus55) / 1003 M.-Nr. 05 585 961 / V00 This paper consists of cellulose which has been bleached without the use of chlorine.
