Operating Instructions Dishwasher G 2832 To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Caring for the environment . . . . . . .
Contents Settings ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Drying Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Water hardness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 External water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Filter check . . .
IMPORTANT SAFETY INSTRUCTIONS WARNING – When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only.
IMPORTANT SAFETY INSTRUCTIONS Installation ~ The dishwasher must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ , WARNING - Fire hazard Do not cover or crush the plug of the appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug.
IMPORTANT SAFETY INSTRUCTIONS Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. ~ Only use detergents and rinse aids recommended for residential dishwashers. Keep all detergents and rinse aids out of the reach of children. Do not inhale or swallow detergents. ~ Only use the dishwasher if all panels ~ Dishwasher detergents contain irritant are properly in place. ~ Do not tamper with the controls.
Guide to the dishwasher a Upper spray arm (not visible) g Triple filter system b Cutlery tray h Data plate c Upper basket i Child Safety Lock in the door handle (not visible) d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm j Rinse aid reservoir k Dual compartment detergent dispenser l Salt container 7
Guide to the dishwasher Control panel a K (Information) touch control To display more info about the displayed menu b s (On/Off) touch control To turn the dishwasher on and off c Selection touch controls To select a menu point displayed next to the touch control. To change the displayed value (+/-). To browse between menus. d Display See the following pages for more information 8 e Standby indicator The indicator flashes when the dishwasher is turned on but the display is turned off.
Guide to the dishwasher Display The following can be selected in the display : – the wash program – the options ! A bullet in the display next to the touch control shows that a function can be selected with this control. – the start time – the settings J menu – information During a running program the display shows : n The arrows on the right side in the display shows that more selections or text follow and can be displayed with the respective control.
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source. ^ For fastest possible wash times, yet higher energy consumption, connect the dishwasher to a hot water source.
Before using for the first time To open the door To close the door ^ Push the baskets in. ^ Lift the door and push until the catch engages. The door will then close automatically. ,Do not put your hand inside of the door as it is closing. Danger of injury. Child Safety Lock The door will open automatically at the end of the program to aid in the drying process. This function can be deactivated (see "Settings - Drying Plus"). ^ Press the release catch inside the door grip.
Before using for the first time Welcome screen ^ Turn the dishwasher on s. The Welcome screen shows when the washer is turned on for the first time. Language setting The display changes automatically to the language setting. Sprache F ° #eština ° dansk ° deutsch B m OK ° ^ Select the desired language and confirm with OK. The selected language is marked with a L check. Clock format The display changes automatically to the clock format.
Before using for the first time Time of day setting The display changes automatically to the time of day setting. Time of day + ° 12:00 - ° OK ° ^ Set the hours using the +/- controls and confirm with OK. Set the minutes and confirm. Display The display changes automatically to the screen for setting the time of day display. Display ° On ° On for 60 Seconds B ° Do not display OK ° ^ Select the display desired for the time of day, confirm with OK.
Before using for the first time Water softener Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. To achieve good cleaning results, the dishwasher needs soft water. Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4 °d (4 gr/gal [US]), the water should be softened.
Before using for the first time Filling the salt container ,Inadvertently filling the salt container with dishwashing detergent will damage the water softener. ,Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. ^ Remove the lower basket and unscrew the salt container lid. When opening the salt container, water will run out. Open the container only to refill salt.
Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergents, a rinse aid is not needed.
Before using for the first time Rinse aid refill message When the Insufficient rinse aid message first comes on, there will be enough rinse aid left for 2 - 3 washes. ^ Refill rinse aid after the program has finished. If the "Tab" function is selected, the Insufficient rinse aid message will not come on. See "Settings J Detergent". ^ Confirm with OK. The Insufficient rinse aid message will clear from the display.
Loading the dishwasher ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes.
Loading the dishwasher Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand. – When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe.
Loading the dishwasher Split cutlery tray ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge and forks with the prongs between the holders. Spoons should be placed in the opposite direction with the handles between the holders. The upper spray arm must not be blocked by tall cutlery items. The inserts of the cutlery tray can be removed.
Loading the dishwasher Upper basket ,Always use the dishwasher with the upper and lower basket inserted. (except during the Tall items program). Removable spike insert The spike insert can be removed to create more space for larger items, e.g. a saucepan. Removing the insert a: ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans.
Loading the dishwasher Adjustable cup racks Coffee bar ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. (depending on model) Glasses can be leaned against the coffee bar to allow a firm stand. The height of the cup rack can be adjusted in two levels. ^ The bar can also be used to separate two rows of glasses. ^ Pull the cup rack upwards and let it engage at the desired height. 22 ^ To stack wide items, flip the bar to the right.
Loading the dishwasher Universal support bar The support bar will hold tall glasses and stemware securely. ^ Fold the bar down and lean the desired glasses against it. ^ If desired, a section of the cutlery tray can be removed to allow for even taller glasses.
Loading the dishwasher Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. This will block the middle spray arm. Take care when sliding the basket in and out in this position. ^ Slide out the upper basket. ^ Pull up the levers at the sides of the upper basket and adjust the basket height.
Loading the dishwasher Lower basket Foldable spikes ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small plates and saucers can also be arranged in the lower basket. The foldable spikes can be used for small plates and saucers. Two rows of spikes can be folded down, to create more room for larger dishware, e.g. pots, pans and bowls. ^ Press the yellow lever down a and fold down the spikes b.
Loading the dishwasher Removable spike insert The spike insert can be removed in order to make room for larger tableware or to use a different insert. Removeable PlateGuard Plus with StemGuard (depending on model) This insert is ideal for cups, glasses, plates, bowls, pots and pans. Removing the insert ^ To remove the insert, gently pull the handle upwards. ^ To arrange tall items the cup rack can be raised.
Loading the dishwasher Vase / Bottle insert (depending on model) The vase / bottle insert can be used to rinse narrow items, e.g. vases, baby bottles, etc. Removing the insert a: ^ To remove the insert, gently pull the handle upwards. Inserting the insert b: ^ Place the insert into the lower basket. ^ Slide the hitches of the insert under the struts of the lower basket. ^ Push down on the handle to snap the insert into position. ^ Place the insert into the lower basket as shown in the illustration.
Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine.
Use Detergent ,Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Fill the detergent dispenser only when you are ready to start the dishwasher. ,Only use detergents formulated You can use powder, gel or tab detergents. Follow the dosage information on the detergent packaging. See "Settings J - Tab" for more information on detergent usage.
Use Adding detergent ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. ^ To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. 30 The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively.
Use Turning on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if closed. ^ Turn the dishwasher on by touching the s control. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. See "Settings J - Memory". Main menu 12:00 ° Normal ° Pots & Pans ° China & Crystal : m Selecting a program Choose a program according to the type of load and soiling.
Program guide Program When to use Program sequence Pre rinse Normal For normally soiled dishware with dried on food Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, 120% detergent recommended Main wash 1 2 x x 1 x x as required x For temperature sensitive glassware and lightly soiled dishware, 50% detergent recommended; sensor controlled GlassCare program Express "Quick program" for lightly soiled dishware, e.g.
Program guide Program When to use Program sequence Pre-rinse 1 2 Main wash Interim rinse 1 2 Final rinse Drying x x x x x x x x x x x x x Starch/Cheese For dishware with dried on starchy or cheesy food; 120% detergent recommended x x x x x LG items soiled x x x x x Glassware - no To wash glassware rinse aid warm without detergent and rinse aid; rinse cycle with warm water x x x Glassware - no For a quick cleaning of rinse aid cold glassware for direct reuse; use without
Use ^ Select the desired options. The detergent type can now be set. You can choose between normal powder, gel or Tabs. See "Settings J - Detergent". The selected options are marked with a L check. ^ To de-select an option press the respective touch control again. Selecting options ^ Confirm the selected options with OK. Options can be added to the selected program. The display changes back to the program menu. The message Options selected appears. ^ Select the Options menu.
Use Starting a program Time display ^ Select Start. Before the program starts, the time display shows the running time of the selected program in hours and minutes. During the running program the remaining time is shown in the time display. The program starts and Dishes can be added appears in the display. As long as this reference is shown, tableware can be added to the machine without impairing the cleaning result. Cancel a program only in the first few minutes. Otherwise important program steps (e.g.
Use At the end of a program Interrupting a program At the end of a program the display shows Program finished or Drying plus with the door slightly open (if activated). A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted. Dishes tend to chip if removed still hot from the dishwasher.
Use Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: 12:00 Sensor Wash Pre-rinse Time left 1:30 h Cancel ° ^ Select Cancel. ^ Confirm the message Cancel program? with OK. The program is canceled. Sensor Wash 12:00 Program finished Main menu ° ^ Select Main menu. The display changes to the main menu. ^ Select and start the desired program.
Additional options Delay start The starting time of a program can be delayed between 15 minutes and 24 hours. The start can be delayed in 15-minute-increments. When using the "Delay Start" function make sure that the detergent compartment is dry before adding detergent, use a cloth if necessary. The detergent might stick together and not get completely rinsed out. Do not use liquid detergent when selecting "Delay Start", the detergent could leak out of the compartment.
Additional options 12:00 Sensor Wash Start at 12:00 Cancel ° The program name and start time are displayed. The program starts automatically at the selected time. Starting a program before the delay start has elapsed: A program can be started before the delay start time has elapsed. ^ Select Cancel and confirm with OK. ^ Select Main menu. The display changes to the main menu. ^ A program can now be selected and started.
Settings ! The "Settings J" menu allows you to adjust standard settings Open the Settings J menu ^ Turn the dishwasher on s. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. See "Settings J - Memory". In this case, switch to the main menu by touching "Clear". Main menu 12:00 ° Settings F ° Normal ° Pots & Pans m ^ Select Settings J. The display changes into the "Settings J" menu.
Settings ! Language J Time of day The display contents can be shown in different languages. This selection allows the clock to be shown as 24 or 12 hours and to set the clock. The displayed language can be changed by the submenu "Language J". ^ Select the desired language and confirm with OK. The flag behind the word "Language J" serves as a guide when an unfamiliar language is selected. Select the respective menu with a flag until the submenu Language J appears.
Settings ! Detergent Tab To achieve best results the used detergent can be set on your dishwasher. The selections available are "Powder", "Gel" and "Tab". The program cycle sequence will be adjusted for the selected detergent. Depending on the program the program running time could increase. If the "Tab" indicator is lit than the program sequence is adapted to suit detergents than contain rinse aid and salt (as well as other components where applicable).
Settings ! Drying Plus The Drying plus function automatically opens the door slightly at the end of a program, in order to improve the drying process. This function can also be deactivated. ^ Select the desired setting and confirm with OK. Water hardness The dishwasher is equipped with a sensor softener, which automatically detects the hardness of your tap water. The water hardness level set to the water softener can be checked in the display under the submenu "Water hardness".
Settings ! External water softener Filter check If the dishwasher is connected to an external water softener unit which is regenerated with salt, the water hardness must still be set in the dishwasher. Set the dishwasher to the water hardness of your water softener unit (see "Before using for the first time"). This selection allows you to set the number of cycles run before the filter check message shows. You can select between 30 and 60 cycles.
Settings ! Reorganize program list The order of the programs in the program list can be reorganized. Frequently used programs can be saved to the first three positions. Select program for position 1 12:00 ° Normal B ° Pots & Pans ° Cancel m Continue ° ^ Select the program to be saved to the first program list position. ^ Confirm with Continue. ^ Repeat for the program to be saved to the second and third program list position. ^ Confirm each selection with Continue. The selected programs are now shown.
Settings ! Save options Additional options can be selected for some programs, e.g. extended drying. See "Use - Selecting options". Save options allows you to save the selected options for future use of the program. This function is turned off by default. ^ Select the desired setting and confirm with OK.
Settings ! Child Safety Lock The Child Safety Lock protects the dishwasher from misuse. If the dishwasher is turned on while the Child Safety Lock is activated, the display shows The appliance is locked. The lock must be deactivated before the dishwasher can be used. As long as the Child Safety Lock is activated, the dishwasher is locked every time it is turned on. The function is turned off by default. ^ Select On and confirm with OK. Unlocking the dishwasher ^ Turn the dishwasher on "K".
Settings ! Temperature Buzzer volume The temperature can be displayed in "°C/Celsius" or "°F/Fahrenheit". Two buzzer volumes can be selected or the buzzer can be turned off. The temperatures are shown in °C/Celsius by default. Off ^ Select the desired temperature unit and confirm with OK. The buzzer tone at the end of a program is turned off. Soft Buzzer The tone sounds in a soft volume. When the buzzer is activated, a tone sounds at the end of a program and if a fault occurs.
Settings ! Button tone Memory A tone will sound when a button is pressed. The memory function allows you to save the last selected program. The volume can be set to 17 different levels. It is set to level 8 by default. When turning the dishwasher off and on again after a program has finished or opening and closing the door, the last selected program is displayed instead of the main menu. ^ Select the desired setting and confirm with OK. Brightness The function is turned on by default.
Settings ! Dealer = Demo modes are only for showrooms. The dishwasher has three demo programs for showrooms. The programs "Demo mode" and "Endless demo mode" show the use and function range of the dishwasher. – Demo mode: The program is started by pressing any button. It runs once and must be started again. – Endless demo mode: The program starts as soon as it is activated and runs in a loop until it is turned off. – Demo wash sound: – ^ Select the desired option, confirm with OK.
Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Issue After the dishwasher was turned on the display stays off and the stand by indicator does not flash. The dishwasher stops during a program.
Frequently asked questions Problem Possible fault Solution Automatic door closing fault The door may be blocked. – Remove the item, if necessary restart the program. – If the message shows again contact Miele Technical Service. Automatic door opening fault Possible technical fault. – Open the door by hand and restart the program. – If the message shows again contact Miele Technical Service. The buzzer sounds.
Frequently asked questions Problems water intake/drain Issue The buzzer sounds. The display shows the following: Possible fault Solution No water intake Open the water faucet The water supply is closed. Open the water supply all the way. Fault water intake FXX Before fixing the fault: – Turn the dishwasher off by touching the s control. Fault F12/F13: Fault in the water intake. – Open the water supply all the way and restart the program.
Frequently asked questions Issue Possible fault The program "Energy The intake water does not Saver" displays the have a minimum fault: temperature of 115°F Water intake temp. too (45°C). See "Plumbing low Connection to the water supply". The buzzer sounds. The display shows the following: Fault in the water drain. Drain fault FXX There might be water in the wash cabinet. 54 Solution – Restart the program. – If the fault is displayed again, use a different program.
Frequently asked questions General problems with the dishwasher Issue The display remains off. Possible fault The display has gone into "Standby" mode to save energy. Solution Touch any control. The display shows the following: The middle or lower spray arm is blocked by dishware. Open the dishwasher door and rearrange the items blocking the spray arms. Middle spray arm blocked or Lower spray arm blocked The spray arm jets of – Turn the dishwasher off by the middle or lower touching the s control.
Frequently asked questions Issue Possible fault Solution Detergent is left in the dispenser at the end of a program. The detergent lid cannot be closed properly. The door and the interior walls are still wet after a program has finished. Water remains in the wash cabinet at the end of a program. The dispenser was damp when detergent was added. Detergent residue is blocking the catch. This is not a fault. It is the normal operating mode of the drying system. Dry the dispenser before adding detergent.
Frequently asked questions Sounds Issue There is a knocking noise in the wash cabinet. There is a rattling noise in the wash cabinet. There is a knocking noise in the water pipes. Possible fault Solution The spray arm is hitting an Interrupt the program, item in the basket. rearrange items blocking the spray arms. Items are not secure in the Interrupt the program and wash cabinet. rearrange loose pieces. This may be caused by the installation or the diameter of the pipe.
Frequently asked questions Poor cleaning results Issue The dishes are not clean. Possible fault The dishes were not loaded correctly. The program was not powerful enough. Stubborn but normal soiling (e.g. coffee, tea). Solution See "Loading the dishwasher". Select a more intensive program, see "Program Guide". Use the function "Adjust Sensor Wash". See "Settings J - Adjust Sensor Wash". Not enough detergent was Use more detergent, see dispensed. "Adding detergent". The spray arms are blocked.
Frequently asked questions Issue Possible fault Solution Dishes are not dry, The rinse aid setting may be Increase the dosage, refill glasses and cutlery too low, or the rinse aid the reservoir or switch the are spotted. reservoir is empty. rinse aid product when refilling, see "Before using for the first time". Leave dishes in longer, see Dishes were taken out too soon. "Use". Set the Detergent setting for A "Tab" product was used. These products have a low a normal (powder or gel) drying effect.
Frequently asked questions Issue Possible fault Glasses are Detergent deposits. discolored and the film cannot be wiped off. Glasses are dull and Glasses are not dishwasher discolored, film safe. cannot be wiped off. Tea or lipstick stains The wash temperature of have not been the selected program was completely removed. too low. The detergent has a low bleaching effect. Plastics are Natural dyes e.g. from discolored. vegetables may be the cause. Not enough detergent was used to break down natural dyes.
Comparison Tests 10 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray 61
Comparison Tests 12 place settings, Standard program: Normal Upper basket Cutlery tray 62 Lower basket
Comparison Tests 14 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray 63
After sales service Repairs MieleCare In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. (USA only) ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology.
Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. Residual water in the machine could leak and cause electrical damage.
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use.
Cleaning and Care Exterior Check and clean your dishwasher regularly (approx. every 4-6 months). This will help avoid problems and faults. ^ Only use a conditioner suitable for your kitchen cabinetry. ,Abrasive cleaning agents, glass ^ Clean the front with a solution of warm water and liquid soap applied with a soft sponge. Dry with a soft cloth. cleaning agents, all-purpose cleaners, thinner or ammonia based cleaners should not be used on the dishwasher. They will damage the surface.
Cleaning and Care Triple filter system Cleaning the triple filter The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones, etc.). ,The machine must not be used without all the filters in place! Check and clean the filter system every 4-6 months or whenever a foreign object is trapped.
Cleaning and Care To clean the underside of the filter the flap must be opened. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Push the clips together a and open the flap b. ^ Lock the filter by turning the handle clockwise. ^ Rinse under running water. ^ Close the flap so that the clip engages. 70 ,The triple filter system must be inserted and locked. Large particles could get in the circulation system and cause blockage.
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
Cleaning and Care Cleaning the water inlet filter A filter is incorporated into the intake hose attached to the dishwasher’s shut off valve. If your water is hard or the pipes contain sediment, this filter may clog and prevent enough water from entering the wash cabinet. ,The plastic housing of the water connection contains electrical wiring. Do not cut the intake hose or submerge it in liquid.
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. The drain pump is beneath the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (glass or bone splinters).
Installation Instructions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions.
Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door.
Plumbing Waterproof system All Miele dishwashers have a safety valve located on the incoming water line and a sealed underside with a water sensor. If a fault occurs, the water intake is stopped and the drain pump is activated. Water damage, if any, is minimized. Providing the dishwasher was installed correctly by a Miele technician, the waterproof system will protect you from water damage throughout the lifetime of the machine.
Plumbing Drainage Venting the drainage system – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor, the drain must be vented. Otherwise the water inside the dishwasher may siphon out during the wash program. – The dishwasher is equipped with a 5 ft (1.
RemoteVision The Miele RemoteVision system is designed to send messages directly to Miele and/or your PC. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual. Be sure your wireless system meets the following requirements – Windows XP® or newer operating system, Mac® OS X 10.3 or higher – Cable or DSL modem – Microsoft® Internet Explorer 6 or higher, Safari 2.0 or higher, Firefox 1.
Alterations reserved/4308 G 2832 For the most updated manual see the Miele web site. M.-Nr.
