Operating and installation instructions Cooker hood To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
Contents Warning and Safety instructions .......................................................................... 4 Caring for the environment ................................................................................. 13 Modes of operation.............................................................................................. 14 Con@ctivity 2.0 function ........................................................................................ 15 Guide to the appliance...........................
Contents Appliance dimensions............................................................................................ 34 Safety distance between hob and cooker hood (S)............................................... 35 Installation recommendations................................................................................ 36 Protective foil ......................................................................................................... 36 Connection for air extraction ......................
Warning and Safety instructions This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important notes on the safety, installation, use and maintenance of the appliance. Miele cannot be held liable for non-compliance with these instructions.
Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the cooker hood unless they are constantly supervised. Children 8 years and older may only use the cooker hood unsupervised if they have been shown how to use it safely and recognise and understand the consequences of incorrect operation. Children must not be allowed to clean or maintain the cooker hood unsupervised.
Warning and Safety instructions Technical safety Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician. A damaged appliance can be dangerous. Check it for visible signs of damage. Do not use a damaged appliance. The electrical safety of this appliance can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met.
Warning and Safety instructions For safety reasons, this appliance may only be used after it has been built in. The cooker hood must not be used in a non-stationary location (e.g. on a ship). Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults. Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet.
Warning and Safety instructions Using at the same time as other heating appliances that depend on the air from the room Warning - danger of toxic fumes Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room.
Warning and Safety instructions In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure in the room of 0.04 mbar (4 pa) is the maximum permissible.
Warning and Safety instructions Correct use Never use a naked flame beneath the cooker hood. To avoid the danger of fire, do not flambé or grill over a naked flame. When switched on, the cooker hood could draw flames into the filter. Fat deposits could ignite, presenting a fire hazard. The cooker hood can become damaged when exposed to excessive heat. – When using the cooker hood over a gas hob, ensure that any burners in use are always covered by a pan.
Warning and Safety instructions Do not use the cooker hood without the filters in place. This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation. There is a risk of fire if the cooker hood is not cleaned as described in these operating instructions. The cooker hood can get very hot during cooking due to heat rising from the hob. Do not touch the housing or the grease filters until the cooker hood has cooled down.
Warning and Safety instructions Metal parts can have sharp edges which may cause injury. Wear gloves to protect your hands from being cut. Exhaust ducting must be of non-inflammable material. Suitable material is available from Miele specialist dealers or the Miele Spares Dept. The appliance must not be connected to a chimney or flue which is in use. Neither should it be connected to ducting which ventilates rooms with fireplaces.
Caring for the environment Disposal of the packing material The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites.
Modes of operation Depending on the model of the cooker hood, the following options are available: Extraction mode The air is drawn in and cleaned by the grease filters and directed outside. Non-return flap Recirculation mode (DA 420V-6 only, with conversion kit and charcoal filter, available as optional accessories, see "Technical Data") The air is drawn in and cleaned first by the grease filters and then by a charcoal filter. The cleaned air is then recirculated back into the kitchen.
Modes of operation Con@ctivity 2.0 function Automatic control The cooker hood has a communication facility which enables the automatic operation of the cooker hood depending on the operational state of the hob. The hob transmits information about its operational status via a wireless signal to the cooker hood. – When the hob is switched on, the hob lighting comes on independently and then after a short time the fan also comes on.
Guide to the appliance 16
Guide to the appliance a Telescopic extension piece b Tower c Height-adjustable canopy d Controls e Grease filters f Spacer frame The spacer frame creates a shadow gap between the tower and the ceiling. The cooker hood can be installed with or without the spacer frame.
Operation (Automatic mode) When Con@ctivity 2.0 is activated, the cooker hood always works in automatic mode (see "Activating Con@ctivity 2.0"). To operate the cooker hood manually, see "Cooking without Con@ctivity 2.0". Cooking with Con@ctivity 2.0 (Automatic mode) Switch a cooking zone on at the power level you want. The cooker hood lighting will come on. After a few seconds the fan will come on, first at power level 2, then it will switch immediately to power level 1.
Operation (Automatic mode) Cooking process Switching off If for example you switch on a cooking zone at the highest power level to heat a pan for frying and reduce the power level after approx. 60 to 90 seconds*, a cooking process is recognised (*60 seconds to 5 minutes for a HiLight hob). Switch off all cooking zones. The cooker hood switches itself on and when the hob power level has been reduced, the hood switches to power level 3 and remains at that level for approx. 5 minutes.
Operation (Automatic mode) Leaving automatic mode temporarily To leave automatic mode temporarily during cooking: Manually select a different power level, or Manually switch the cooker hood off, or Activate the run-on option on the cooker hood. The fan will switch off after the selected time and the lighting remains switched on. The cooker hood can now be operated manually (see "Cooking without Con@ctivity 2.0").
Operation (Manual mode) Cooking without Con@ctivity 2.0 (Manual mode) The cooker hood can be operated manually if: – Con@ctivity 2.0 is not activated. – You have temporarily deactivated Con@ctivity 2.0 (see "Leaving automatic mode temporarily"). Switching the fan on After you have finished cooking, press the run-on option control 5 15 – Once: the fan will switch itself off after 5 minutes (5 lights up). – Twice: the fan will switch itself off after 15 minutes (15 lights up).
Operation (Manual mode) Dimming/switching the hob lighting on/off The hob lighting can be switched on and off and dimmed independently of the fan. Press the lighting control briefly to switch it on and off. The lighting will switch on at maximum brightness. Switching Power management on/off You can deactivate Power management. This can result in increased electricity consumption. Switch off the fan and the lighting. Press the run-on option button 5 15 for approx.
Operation (Automatic and Manual modes) Operating hours counters The number of hours the appliance has been in operation is stored in memory. When the Grease filter symbol or the Charcoal filter symbol lights up, the operating hours counters are signalling that the filters need to be cleaned or changed. Further information about cleaning and changing the filters and resetting the operating hours counter can be found under "Cleaning and care".
Operation (Automatic and Manual modes) Activating and altering the charcoal filter operating hours counter Reading the filter operating hours counter The charcoal filter is needed for recirculation mode. To check the percentage of time set already used The operating hours counter for the charcoal filter needs to be activated once and the operating hours counter needs to be set to suit the kind of cooking you do: Use the On/Off control to switch the fan on.
Operation (Automatic and Manual modes) Adjusting the height of the canopy The height adjustment feature on the canopy can be used to – – adapt the height of the hood to suit the installation conditions. – adjust the working area underneath the hood to the height of the user. – maximise vapour extraction by lowering the canopy during particularly intensive cooking. – create more working space above the hob by raising the canopy when required.
Energy saving tips This cooker hood operates very efficiently and economically. The following will help you to save even more energy when using it: – Ensure that there is sufficient ventilation in the kitchen when cooking. In extraction mode, if there is insufficient air flow the cooker hood cannot operate efficiently and this causes increased operating noise levels. – Always cook with the lowest possible setting.
Cleaning and care Casing General information The surfaces and controls are susceptible to scratches and abrasion. Please observe the following cleaning instructions. All external surfaces and controls can be cleaned using hot water with a small amount of washing-up liquid applied with a well wrung-out soft sponge or cloth. Do not let moisture get into the cooker hood. Only use a damp cloth when cleaning. This is particularly important around the controls.
Cleaning and care Important for the controls Do not leave soiling on the controls for any length of time. Otherwise they may suffer discolouration or damage. Remove soiling straight away. Please observe the general notes on cleaning earlier in this section. Do not use stainless steel cleaning agents on the controls. Grease filters The re-usable metal grease filters in the appliance remove solid particles (grease, dust, etc.) from the kitchen vapours, preventing soiling of the cooker hood.
Cleaning and care Cleaning the grease filters in the dishwasher Place the filters as upright as possible in the lower basket, with the short sides upright, ensuring the spray arm is not obstructed. To take out a grease filter, release the locking clip on the filter, lower the filter approx. 45°, unhook it at the back and remove it. Cleaning the grease filters by hand Clean the filters with a soft nylon brush in a mild solution of hot water and a small amount of washing-up liquid.
Cleaning and care If a grease filter is inadvertently replaced upside down, insert a small screwdriver blade into the slit to disengage the clip. Resetting the grease filter operating hours counter After cleaning, the operating hours counter needs to be re-set. Whilst the fan is switched on, press the operating hours control for approx. 3 seconds, until only the 1 is flashing. The grease filter symbol goes out.
Cleaning and care When to change the charcoal filter Always replace the charcoal filter when it no longer absorbs kitchen odours effectively. It should, however be replaced at least every 6 months. The charcoal filter operating hours symbol will light up to remind you to change the charcoal filter regularly. The charcoal filter operating hours counter needs to be activated before using for the first time (see "Operation").
After Sales / Guarantee In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or the Miele Service Department. Contact details for Miele are given at the back of this manual. N.B. A call-out charge will be applied to service visits where the problem could have been resolved as described in these instructions. When contacting your dealer or Miele, please quote the model and serial number of your appliance. These are shown on the data plate.
Installation Before installation Before installation, it is important to read the information given on the following pages as well as the "Warning and Safety instructions" at the beginning of this booklet. 4 extension piece holders for aligning and securing the telescopic extension piece Assembly parts 4 screws M4 x 8.
Installation Appliance dimensions a Installation area: cut-out for feeding through the exhaust ducting, the mains cable and with ...EXT models, the connection cable to the external motor. In recirculation mode, only the mains cable is required. b Alternative installation with spacer frame c Ventilation grille positioned at the top for recirculation d A mains connection cable is required to connect the cooker hood to the socket in the ceiling. With air extraction mode flexible ducting is also required.
Installation Safety distance between hob and cooker hood (S) When planning the installation height of your cooker hood, the minimum safety distance between the top of a cooker or hob and the bottom of the cooker hood is as follows, unless a greater distance is specified by the manufacturer of your cooking appliance. See "Warning and Safety" instructions for further information.
Installation Installation recommendations Protective foil – When deciding on the safety distance between the hob and cooker hood, please note that a distance of 650 mm above electric cookers/hobs may be preferable to give more working space under the hood. The housing components have protective foil around them to protect them from transport damage. – Account should also be taken of the height of the person who will be using the hood most often.
Installation With air extraction mode: Draw two intersecting lines on the ceiling. – Place a section of the exhaust ducting in the ceiling and feed it down through the cross-sectional area as illustrated. Exhaust ducting of approx. 200 mm length is required between the ceiling and the cooker hood exhaust socket. – Secure the exhaust ducting to the exhaust socket, e.g. with a hose clip (available as an optional accessory) on flexible ducting. Place the mains cable and for ...
Installation Use a knife to release the four spacers and the two covers from the spacer frame supplied. Drill four holes 10 mm, approx. 115 mm deep for the plugs supplied. Use the space frame as a drilling template. Place it on the ceiling with the arrows pointing forwards. Using the notches, align the spacer frame on the intersecting lines and make pencil marks for the drill holes. 38 Place the four plugs in the holes and screw in the 4 screws so that they protrude by approx. 30 mm.
Installation The cooker hood is supplied ready for extraction mode. For recirculation mode (UL), the directional unit from conversion kit DUI 32 (optional accessory, DA 420V-6 only) is installed and the telescopic piece turned upside down. Loosen the two telescopic piece clamps from the installation frame. Pull the telescopic piece inside upwards to remove.
Installation Fix the top part to the side of the installation frame for now. Loosen the fixing screws and remove the top part of the installation frame.
Installation Loosen the screws from the exhaust socket and the hose inside and remove the exhaust socket. It is not required for recirculation mode. Place the directional unit in the installation frame with the arrows pointing to the sides. Remove the non-return flap. It is not required for recirculation mode. Rotate the directional unit by 90° so that the arrows now point forwards and backwards.
Installation Secure the hose to the directional unit socket using a hose clip. Check that the hose is held securely. Replace and secure the top part of the installation frame.
Installation Replace the telescopic piece with the recirculation grilles at the top. The spacer frame can be installed between the tower and the ceiling. This creates a shadow which gives the illusion of a gap between the ceiling and the tower. This is useful if the ceiling is not level or is uneven. The cooker hood is aligned vertically with the spacers supplied. Visual irregularities between the tower and the ceiling are then concealed by the shadow.
Installation Mount the spacer frame onto the installation frame. Hang the cooker hood on the four screws, making sure the controls are at the front. If using the spacer frame, place the two covers into the fixing holes.
Installation Place the exhaust ducting onto the exhaust socket. For ...EXT models only: Connect the cooker hood and the external motor using the connection cable. Align the installation frame and secure it with the screws. The spacers, which were removed from the spacer frame at the start, can be used to align the cooker hood vertically. Connect the mains cable. See "Electrical connection".
Installation Remove the grease filters from the cooker hood. Remove the safety screw for the tower on the inside of the frame. Fit the four telescopic piece clamps between the tower and the telescopic piece. The internal telescopic piece rests on the clamps. When the screws are tightened, the clamps spread out and push the telescopic piece upwards.
Installation 1x T20 M4x16 Insert the safety screw on the inside. With recirculation mode (UL) cooker hoods, insert the charcoal filter. Hold the tower securely, bend back the retaining tabs and carefully lower the tower. The tower will locate in the cut-out in the canopy.
Installation Carefully remove the protective foil from the grease filters. Replace the grease filters.
Connection for air extraction If this cooker hood is used at the same time as a heating appliance that relies on oxygen from the same room there is a risk in certain circumstances of toxic fumes building up. It is essential that the "Warning and Safety" instructions are observed. The cooker hood should be installed according to local and national building regulations. Seek approval from the building inspector where necessary. – Ensure that all connections are strong and airtight.
Connection for air extraction Silencer To achieve even further reductions in noise levels, a special silencer (optional accessory) can be fitted in the ducting system. Extraction mode The silencer not only reduces noise from the motor outside the house, but also sounds from outside (e.g. traffic noise). For this reason the silencer must be positioned as close as possible to the ducting exit .
Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appliance until after installation or repair work has been carried out.
Activating Con@ctivity 2.0 Installing the Con@ctivity 2.0 Stick In order to use the Con@ctivity 2.0 function, the hob must first be fitted with the Con@ctivity 2.0 Stick. Please read the separate installation instructions supplied with the Con@ctivity 2.0 Stick. Activating the cooker hood The hob and cooker hood must be switched off. Press the run-on option button 515 for approx. 10 seconds until the indicator for power level 1 lights up.
Activating Con@ctivity 2.0 Activating the hob Activation failed While the cooker hood is searching for a signal, start activating the hob. More information about this can be found in the Operating instructions for the hob. If connection cannot be established despite activating the Con@ctivity function on the cooker hood and hob, the function must be deactivated on both appliances and then the procedure repeated.
Technical data Fan motor* 130 W Variable height motor 175 W Hob lighting Total connected load* Voltage, frequency 4x3W 317 W AC 230 V, 50 Hz Fuse rating 5A Weight DA 420V-6 37 kg DA 424V-6 45 kg DA 420V-6 EXT 34 kg DA 424V-6 EXT 42 kg * For EXT models, the connected load and extraction power will depend on the type of external motor fitted. Length of connection cable to external motor: 1.
Technical data Data sheet for domestic cooker hoods In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
Technical data Data sheet for domestic cooker hoods In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
Technical data Data sheet for domestic cooker hoods In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
Technical data Data sheet for domestic cooker hoods In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
United Kingdom Miele Co. Ltd. Fairacres, Marcham Road Abingdon, Oxon, OX14 1TW Customer Contact Centre Tel: 0330 160 6600 E-mail: mielecare@miele.co.uk Internet: www.miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive, Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Miele (Shanghai) Trading Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500, Fax: +86 21 6157 3511 E-mail: info@miele.
DA 420V-6 DA 420V-6 EXT DA 424V-6 DA 424V-6 EXT en-GB M.-Nr.
