Installation Instructions DA5960 W en-CA Read these instructions and the "Important Safety Instructions" before installing this hood. Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions.
Caring for the environment Disposal of packing material Disposal of an old appliance The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Please recycle. Old appliances may contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. ,DANGER Ensure that any plastic wrappings, bags, etc.
Appliance dimensions 22
Appliance dimensions dai2479 1) Air extraction mode 2) Recirculation mode 3) Recirculation vent installed upwards 4) and 5) Installation area Wall/ceiling area respectively for vent hole and outlet installation. For recirculation mode only 4) and only outlet installation.
Appliance dimensions Distance between cooktop and hood (S) Do not install this exhaust hood over cooktops burning solid fuel. Provided a larger distance is not given by the manufacturer of the cooktop, follow the minimum safety distances between a cooktop and the bottom of the hood: Miele cooktops: - 24" (610 mm) above electric surfaces, - 26" (660 mm) above electric grill/boiler/fryers, - 24" (610 mm) above gas surfaces ß 25,000 BTU's (7.
Appliance dimensions Use the following distances when preparing a rear wall (screw ø 5 mm). *The middle retaining plate can vary in position, depending on the ventilation gap and the position of the outlet. It should be mounted as low as possible. If the exhaust hood is being mounted directly on the wall, follow the enclosed assembly.
Installation accessories dai2417 26
Installation accessories a 3 protective shields to prevent scratches to the chimney during installation. b 2 hose clips for securing the ducting. 8 large headed screws 5 x 40 mm for securing the retaining plates and the canopy c 1 reducing collar for use with 5" (125 mm) exhaust ducting.
Plywood backing The majority of the weight of the installed ventilation system will be supported by the lower retaining plate. It must be firmly attached to the stud framing behind the drywall. If studs are not available in the required locations, a plywood backing (min. ½" (13 mm) thick) spanning at least two studs must be installed. Failure to adequately support the weight as stated may result in the ventilation system falling off the wall, causing personal injury and property damage.
Installation Installation instructions Dismantling ^ See the enclosed installation instruction diagram. If the hood needs to be disassembled, follow the instructions on the installation diagram in the reverse order. ^ Please read the "Important Safety Instructions" and Installation instructions before installing this hood. A lever is enclosed for easier removal of the chimney extension. Protective film The casing is covered with a protective film to prevent scratching during transport.
Air extraction ,WARNING Danger of toxic fumes. Gas cooking appliances release carbon monoxide that can be harmful or fatal if inhaled. To reduce the risk of fire and to properly exhaust air, the exhaust gases extracted by the hood should be vented outside of the building only. Do not vent exhaust air into spaces within walls or ceilings or in attics, crawl spaces or garages. To reduce the risk of fire, only use metal ductwork.
Air extraction Condensate trap optional accessory In some cases, a condensate trap may also be required to collect and evaporate any condensate which may occur. This optional accessory is available for ducts 5" (125 mm) and 6" (150 mm) in diameter. – If the exhaust is ducted into an inactive flue, the air must be expelled parallel to the flow direction of the flue. Never connect an exhaust hood to an active chimney, dryer vent, flue, or room venting ductwork.
Electrical connection ,WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: All electrical work should be performed by a qualified electrician in strict accordance with national regulations (for USA: ANSI-NFPA 70) and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. Ensure that power to the appliance is OFF while installation or repair work is performed.
Technical data Maximum load . . . . . . . . . . . . . . 400 W Fan . . . . . . . . . . . . . . . . . . . . . . 350 W Overhead lighting . . . . . . . . . 1 x 50 W Voltage . . . . . . . . . . . . . . . . . . . . . 120 V Frequency . . . . . . . . . . . . . . . . . . 60 Hz Circuit rating. . . . . . . . . . . . . . . . . . 15 A Weight: DA 5960 W . . . . . . . . 49.6 lbs (22.5 kg) DA 5980 W . . . . . . . . . . 55.1 lbs (25 kg) DA 5990 W . . . . . . . . 56.2 lbs (25.
Alteration rights reserved / 1209 For the most updated manual see the Miele web site. M.-Nr.
