Operating and installation instructions Cooker hood DA 3060 To avoid the risk of accidents or damage to this appliance, it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Cleaning and care . . . . . . . . . . . . . . . . . . .
Caring for the environment Disposal of the packing material Disposal of your old appliance The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Electrical and electronic appliances often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your appliance.
Warning and Safety instructions This appliance complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important information on the safety, installation, use and maintenance of the appliance.
Warning and Safety instructions Technical safety ~ Before installation, check the cooker hood for visible signs of damage. Under no circumstances should you use a damaged appliance. A damaged appliance is dangerous. ~ Before connecting the appliance to the mains supply, make sure that the voltage and frequency details given on the data plate correspond with the on-site electricity supply, otherwise the appliance could be damaged. Consult a qualified electrician if in any doubt.
Warning and Safety instructions ~ Do not connect the appliance to the mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). Using at the same time as other heating appliances that depend on the air from the room Warning - danger of toxic fumes ~ This appliance must not be used in a non-stationary location (e.g. on a ship).
Warning and Safety instructions In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously, an underpressure of 0.04 mbar (4 pa) is the maximum permissible in the room. Correct use ~ Never use an open flame beneath the cooker hood. To avoid the danger of fire, do not flambé or grill over an open flame. When switched on, the cooker hood could draw flames into the filter.
Warning and Safety instructions ~ The filters should be regularly cleaned or changed as appropriate. Saturated filters are a fire hazard. See "Cleaning and care". ~ The cooker hood can get very hot during cooking due to heat rising from the hob. Do not touch the housing or the grease filters until the cooker hood has cooled down. ~ Do not use a steam-cleaner to clean this appliance. Pressurised steam could reach the electrical components and cause a short circuit.
Description of the functions The cooker hood works with . . . air extraction: The air is drawn in, cleaned by the grease filter and then directed outside. If the on-site ventilation system does not have a non-return flap, then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. Having a non-return flap fitted in the ducting ensures that air, once ducted to the outside, cannot get back into the room again.
Guide to the appliance 10
Guide to the appliance a Exhaust socket ø 150 mm i Sliding switch for the fan b Control panel ^ Pull out the deflector plate. c Grease filter ^ To switch on, slide the switch to the required setting. d Pull-out deflector plate e Hob lighting f Charcoal filter (extra accessory available to order for recirculation mode) g Drop-down lightshield to conceal control panel The front of the deflector plate can be fitted with a lightshield to match your kitchen furniture.
Cleaning and care A range of Miele branded cleaning and conditioning agents are available to order through your Miele Dealer / Chartered Agent, the Miele Spare Parts Department, or via the internet on www.miele-shop.com. ,Before any cleaning or maintenance work is carried out, disconnect the cooker hood from the mains supply. ,Halogen lamps get very hot during use and remain hot for some time after being switched off. The hot lamps are also susceptible to damage from damp cleaning.
Cleaning and care Controls The controls may suffer discolouration or damage if soiling is left on them for too long. Remove soiling straight away. Observe the General notes on cleaning earlier in this section. Do not use stainless steel cleaning agents on the controls. Grease filter The re-usable metal grease filter in the appliance removes solid particles from the kitchen vapours (grease, dust, etc) preventing soiling of the cooker hood.
Cleaning and care Cleaning the grease filters by hand ^ Clean the filters with a soft nylon brush in a mild solution of hot water and a small amount of washing-up liquid. Do not use undiluted washing up liquid. ^ When removing the filter for cleaning, also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire.
Cleaning and care Fitting and replacing the charcoal filter If the cooker hood is connected for recirculation, a charcoal filter (optional accessory) must be inserted in addition to the grease filter. This is designed to absorb cooking smells. It is fitted in the canopy above the grease filter. Replacement charcoal filters can be obtained from your Dealer / Chartered Agent or the Miele Spare Parts department or via the internet at www.miele-shop.com.
Cleaning and care Changing a halogen lamp ^ Pull out the deflector plate, and remove the grease filter as described earlier. ^ Switch off the fan and the lighting. ,Exercise caution when changing halogen lamps. They get very hot during use, and remain hot for some time after being switched off. Do not touch the surface directly when changing a lamp, as grease particles from your fingers will adhere to the surface and damage it. Please follow the manufacturer’s instructions.
Appliance dimensions Safety distance between hob and cooker hood The minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows, unless a greater distance is specified by the manufacturer of your cooking appliance: 1) The front section of the wall housing unit must be fitted with a shelf to the depth of the partition wall. 2) The partition wall in the wall unit must be removable.
Installation Installation accessories 18
Installation a 1 exhaust connection for exhaust ducting C 150 mm. b 1 reducing collar for exhaust ducting C125 mm. c 1 non-return flap for fitting into the exhaust socket on the motor unit (only for air extraction mode). 12 screws 3.5 x 16 mm for securing the cooker hood into the wall unit. d 2 brackets to support the appliance in the wall unit. 8 screws M4 x 12 mm for securing the cooker hood to the brackets. e 1 spacer strip to conceal the gap between the rear of the appliance and the wall.
Installation 20
Installation Positioning the appliance in the wall housing unit To position the appliance correctly, cut the spacer strip to required depth T, and then attach it to the back of the appliance. T= Depth of carcase K minus depth of appliance G ^ The depth of appliance G depends on the lightshield being used: ^ Screw the spacer strip to the bottom of the sides of the housing, flush with the rear wall.
Installation ^ Place the appliance on its back. Do not remove the protective film between the deflector plate and the casing until the hood has been placed in the housing unit. ^ Screw the brackets onto the right and left inside walls of the housing unit as shown. The back edge of the brackets should align with the vertical line drawn up from the front of the spacer strip, and the lower edge aligned with the lower edge of the housing unit side wall.
Installation Note for dismantling the cooker hood: Undoing the screws on the left and right inside the housing releases the brackets, allowing the appliance to be removed from the unit. ^ Push the cooker hood back against the spacer strip. ^ Pull out the deflector plate. ^ Lift the appliance up into the housing from below, and engage in the brackets. ^ Secure the appliance to the brackets using 2 screws on each side. ^ Remove the protective film between the deflector plate and the casing.
Installation ^ Secure the front of the appliance to the floor of the housing unit from below using 4 screws. To avoid damaging the deflector plate when it is pulled out, care should be taken to screw the fixing screws in straight, and to ensure that the screwheads are countersunk. ^ Drill respective holes and screw the fixing brackets to the wall or the cabinet rear wall. Tighten the screws to the casing.
Installation Attaching the lightshield Aligning the deflector plate ^ Attach the lightshield (if using). A DML 300 installation kit, available as an optional accessory, is required for this. This installation kit is supplied with the DFB lightshield. Follow the installation instructions supplied. Weight of a lightshield matching existing furniture The lightshield must not exceed 1300 g in weight. This applies to lightshields with a depth of up to 30 mm.
Installation Fitting the grease filter ^ Remove the protective strip around the edge of the grease filter. Fit the grease filter. ^ To do this, pull the deflector plate out. ^ Turn the grease filter so that the red plastic guides are at the front and facing upwards. ^ Fit the grease filter in the front of the deflector plate, press it upwards and push it in together with the deflector plate. It will slide onto the fixing pins at the back. Finally, push the grease filter back a little more.
Installation Set up for extraction mode ^ If the on-site ventilation system does not have a non-return flap, then the non-return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit. ^ When using C 150 mm ducting, secure the exhaust connection supplied to exhaust ducting with hose clips. ^ If using C 125 mm ducting, fit the reducing collar into the exhaust connection, and secure the exhaust ducting to the reducing collar with a hose clip.
Installation Set up for recirculation mode If site conditions are not suitable for the cooker hood to be used with air extraction, the appliance must be set up for recirculation. ^ Fit the conversion kit as described in the installation instructions supplied with the kit. ^ Make sure that the slats on the exhaust grille are directed towards the middle of the room, and not towards the wall or the ceiling. A non-return flap is not used in recirculation mode.
Connection for air extraction Important: To avoid the danger of toxic fumes, please observe the Warning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room. The cooker hood should be installed according to local and national building regulations. Seek approval from the building inspector where necessary. – Where ducting is horizontal, it must be laid to slope away at at least 1 cm per metre.
Connection for air extraction Condensate trap (optional accessory) In addition to insulating the exhaust ducting, we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur. Condensate traps are available for C 125 mm or C 150 mm ducting. When installing a condensate trap, ensure that it is positioned vertically and if possible directly above the exhaust connection. The arrow on the housing indicates the direction of air-flow.
Connection for air extraction Silencer (optional accessory) ...with air extraction: To achieve even further reductions in noise levels, a special silencer can be fitted in the ducting system. The silencer not only reduces noise from the fan, but also sounds from outside (e.g. traffic noise). For this reason the silencer must be positioned as close as possible to where the ducting leaves the building a. ...in recirculation mode: The silencer needs to be positioned between the fan and the exhaust grille b.
Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable. Ensure power is not supplied to the appliance until after installation or repair work has been carried out.
After Sales Service In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer / Chartered Agent or – The Miele Service Department (see back cover for address). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filter is removed. For G.B.
Technical data Connected load. . . . . . . . . . . . . . 210 W Fan motor . . . . . . . . . . . . . . . . . 110 W Hob lighting . . . . . . . . . . . . . 2 x 50 W Voltage . . . . . . . . . . . . . . . . . . . . 230 V Frequency. . . . . . . . . . . . . . . . . ~ 50 Hz Fuse rating GB . . . . . . . . . . . . . . . . . 3 A Fuse rating (IRL). . . . . . . . . . . . . . . 10 A AUS, NZ: Plug rating . . . . . . . . . . . . . . . . . . . 10 A Test marks . . . . . . . . . . Electrical safety . . . . . . . . . . . . . .
Alteration rights reserved / 1111 M.-Nr.
