Operating and installation instructions Cooker hood To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
Contents Warning and Safety instructions...................................................................... 4 Caring for the environment .............................................................................. 13 Guide to the cooker hood ................................................................................. 14 Modes of operation ........................................................................................... 16 Before using for the first time ................................
Contents Grease filters and panel for edge extraction ....................................................... Charcoal filters .................................................................................................... Resetting the charcoal filter operating hours counter .................................... Disposing of charcoal filters ........................................................................... 34 37 37 38 Installation.............................................................
Warning and Safety instructions This cooker hood complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and material damage. Read the operating and installation instructions carefully before using the cooker hood. They contain important information on its safety, installation, use and maintenance. This prevents both personal injury and damage to the cooker hood.
Warning and Safety instructions The cooker hood can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised whilst using it, or have been shown how to use it in a safe way and recognise and understand the consequences of incorrect operation. Safety with children Children under 8 years of age must be kept away from the cooker hood unless they are constantly supervised.
Warning and Safety instructions Technical safety Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician. A damaged appliance can be dangerous. Check it for visible signs of damage. Do not use a damaged appliance. The electrical safety of this appliance can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met.
Warning and Safety instructions For safety reasons, this appliance may only be used after it has been built in. The cooker hood must not be used in a non-stationary location (e.g. on a ship). Touching electrical components and tampering with electrical and mechanical parts is highly dangerous to the user and can cause operational faults. Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet.
Warning and Safety instructions Using at the same time as another heating appliance that depends on the air from the room Danger of toxic fumes! Great care should be taken when using the cooker hood in the same room or the same area of the house at the same time as another heating appliance that depends on the air from the room. Such heating appliances draw in air from the room and duct exhaust gases out through a chimney or extraction ducting.
Warning and Safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliance from being drawn back into the room when the cooker hood and the heater are both operated simultaneously, an underpressure in the room of 0.04 mbar (4 Pa) is the maximum permissible. Sufficient ventilation can be maintained by air inlets which cannot be blocked, e.g. in windows, doors and outside wall vents. The cross-section of the inlet openings must enable sufficient ventilation.
Warning and Safety instructions Correct use Open flames are a fire hazard. The use of an open flame under the cooker hood is not permitted. To avoid the danger of fire, do not flambé or grill over an open flame. When switched on, the cooker hood could draw flames into the filter. Fat deposits could ignite, presenting a fire hazard. The cooker hood can become damaged when exposed to excessive heat. - When using the cooker hood over a gas hob, ensure that any burners in use are always covered by a pan.
Warning and Safety instructions Do not use the cooker hood without the filters in place. This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation. The cooker hood can get very hot during cooking due to heat rising from the hob. Do not touch the housing or the grease filters until the cooker hood has cooled down.
Warning and Safety instructions If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes, seek professional advice. Cleaning and care There is a risk of fire if the cooker hood is not cleaned as described in these operating instructions. Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit.
Caring for the environment Disposal of the packing material Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety.
Guide to the cooker hood 14
Guide to the cooker hood a Exhaust duct Exhaust air can be directed upwards, to the rear or to the left-hand side.
Modes of operation Depending on the model of the cooker hood, the following options are available: Operation with an external motor (EXT/EXTA model cooker hoods) Extraction mode The cooking vapours are drawn in by the cooker hood. The air is then passed via the edge extraction panel through the grease filters, cleaned and then directed outside. Recirculation mode (DUU 2900 conversion kit required) The air is drawn in through the edge extraction panel and then cleaned by the grease filters.
Before using for the first time Selecting extraction mode or recirculation mode The cooker hood is suitable for both extraction mode and recirculation mode. The power of the fan is adapted to suit the selected operating mode. The cooker hood is delivered set up for recirculation mode. It has to be reset for extraction mode. To reset it for extraction mode, the operating hours counter for the charcoal filter(s) has to be deactivated. Switch off the fan and the lighting.
Before using for the first time Miele@home availability For the registration, you will need: The ability to use the Miele app depends on the availability of the Miele@home service in your country. 1. Your WiFi network password 2. Your cooker hood password The Miele@home service is not available in every country. For information about availability, please visit www.miele.com. Miele App The Miele App is available to download free of charge from the Apple App ® Store or from the Google Play Store™.
Before using for the first time Switch the cooker hood off. Connecting via WPS Your WiFi router must support WPS (WiFi Protected Setup). Press and hold the control. Switch the cooker hood off. Press the lighting control at the same time . Press and hold the control. 2 will light up constantly, 3 will flash on and off. The cooker hood will be ready for connection in the next 2 minutes. Follow the instructions in the app. When successfully connected, 2 and 3 will light up constantly.
Before using for the first time Sign out of WiFi (reset to factory settings) Start the WiFi connection on your WiFi router. To set up a new WiFi connection, the existing WiFi connection must be disconnected. Switch the cooker hood off. When successfully connected the 2 and 3 will light up constantly. Quit connection mode on the cooker hood by pressing the Run-on control . The cooker hood can now be operated via the app.
Before using for the first time Setting up Con@ctivity Touch the control. 2 will light up constantly, 3 will flash on and off. After a few seconds, 2 and 3 will flash on and off. The connection has now been disconnected. Quit signing-off mode on the cooker hood by pressing the run-on control . The WiFi connection has now been disconnected. A new connection can now be set up. Con@ctivity is the direct communication system between an electric Miele hob and a Miele cooker hood.
Before using for the first time Con@ctivity via the home WiFi network (Con@ctivity 3.0) Prerequisite: - Home WiFi network - WiFi-enabled Miele hob Connect the cooker hood and hob to your home WiFi network (see “Setting up Miele@home”). The Con@ctivity function will be activated automatically. Con@ctivity via a direct WiFi connection (Con@ctivity 3.0) Prerequisite: - WiFi enabled Miele hob If you do not have a home network, you can establish a direct connection between the hob and the cooker hood.
Before using for the first time Start WiFi connection on the hob. For further details, see the hob operating instructions. When successfully connected, 2 and 3 will light up constantly. Quit connection mode on the cooker hood by pressing the run-on control . Con@ctivity has now been activated. With a direct WiFi connection, it is not possible to connect the hob and the cooker hood to a home network.
Operation (Automatic mode) When Con@ctivity is active, the cooker hood always operates in automatic mode (see “Before using for the first time” – “Setting up Con@ctivity”). If you wish to manually operate the cooker hood, see “Operation (Manual mode)” – “Cooking without Con@ctivity”. Examples for power levels 1 to B Reaction time Cooking with Con@ctivity (Automatic mode) Switch a cooking zone on at the desired power level. The hob lighting will come on.
Operation (Automatic mode) Cooking process Switching off For example, you switch on a cooking zone at the highest power level to heat a pan for frying. You reduce the power level after approx. 10 seconds to 4 minutes (60 seconds to 5 minutes for a for a HiLight hob). Switch off all cooking zones. The cooker hood recognises a cooking process. The cooker hood switches itself on and when the hob power level has been reduced, the hood switches to fan power level 3 and remains at that level for approx.
Operation (Automatic mode) Leaving automatic mode temporarily To leave automatic mode temporarily during cooking: Manually select a different fan power level, or Manually switch the cooker hood off, or Activate the run-on function on the cooker hood. The fan will switch itself off after the selected run-on time, and the lighting will remain on. The cooker hood functions are now operated manually (see “Operation (Manual mode)”).
Operation (Manual mode) Cooking without Con@ctivity (Manual mode) The cooker hood can be operated manually if: - The Con@ctivity function is not activated. - You have temporarily deactivated the Con@ctivity function (see “Operation (Manual operation)” – “Leaving automatic mode temporarily”). Selecting the run-on time It is advisable to run the fan for a few minutes after cooking has finished. This helps to remove any lingering vapours and odours from the air.
Operation (Manual mode) Dimming/switching the hob lighting on/off The hob lighting can be switched on and off and dimmed independently of the fan. Press the lighting sensor briefly to switch it on or off. The lighting will switch on at maximum brightness. With the lighting switched on, press and hold the hob lighting control . The brightness will gradually dim until you release the control.
Operation (Manual mode) Press the control to deactivate Power Management. The 1 and B indicators will flash. Press the control to activate Power Management. The 1 and B indicators will light up constantly. Confirm the setting with the run-on option control . Safety switch-off If Power management has been deactivated, the cooker hood will switch itself off automatically after 12 hours if it has been left on (fan and hob lighting).
Operation (Automatic and Manual modes) Operating hours counter Switch off the fan and the lighting. The cooker hood registers the length of time it has been operated. Press the run-on control and the operating hours control at the same time. When the grease filter symbol or the charcoal filter symbol lights up, the operating hours counters are signalling that the filters need to be cleaned or changed.
Operation (Automatic and Manual modes) Altering or deactivating the charcoal filter operating hours counter Reading the filter operating hours counter Charcoal filters are needed for recirculation mode. You can check the percentage of time set already used before the filter needs replacing. You can set the operating hours counter to suit the type of cooking you do. It has to be deactivated for extraction mode. It is set at the factory for 180 hours of use before the filters need replacing.
Energy saving tips This cooker hood operates very efficiently and economically. The following will help you to save even more energy when using it: - Ensure that there is sufficient ventilation in the kitchen when cooking. In extraction mode, if there is insufficient air flow the cooker hood cannot operate efficiently and this causes increased operating noise levels. - Always cook with the lowest possible setting.
Cleaning and care Before proceeding with any maintenance or cleaning task, the cooker hood must be disconnected from the power supply (see “Warning and Safety instructions”). When cleaning the cooker hood, please note the following: Use a stable ladder. Make sure that you have a secure footing on the ladder. Do not lean over the hob. Do not stand on the worktop or the hob. Housing General information Unsuitable cleaning agents can damage the surfaces and control elements.
Cleaning and care Important information for appliances with stainless steel surfaces This information does not apply to the control buttons. Stainless steel surfaces can be cleaned with a non-abrasive cleaning agent designed specifically for use on stainless steel. To prevent the surfaces from quickly becoming dirty again, we recommend treating them with a stainless steel care product (available from Miele).
Cleaning and care Removing the panel and grease filters The panel and grease filter can fall out when you are handling them. This can result in damage. Make sure you hold the panel and the grease filter securely at all times when handling them. Open the grease filter retainer catch and remove the filter. Cleaning the panel by hand For cleaning purposes, follow the instructions provided under “Housing”.
Cleaning and care Unsuitable cleaning agents After cleaning Unsuitable cleaning agents can cause damage to the surface of the filters if used regularly. Do not use: After cleaning, leave the filters to dry on an absorbent surface before replacing them.
Cleaning and care Resetting the grease filter operating hours counter After cleaning, the operating hours counter needs to be reset. Whilst the fan is switched on, press the operating hours control for approx. 3 seconds, until only 1 is flashing. The grease filter symbol goes out. If you want to clean the grease filters before the operating hours counter has reached its maximum: Press the operating hours control for approx. 6 seconds, until only 1 is flashing.
Cleaning and care To do this, with the fan switched on, press the operating hours control twice, then hold it for approx. 3 seconds until only the 1 is flashing. The Charcoal filter symbol will go out. If you want to replace the charcoal filters before the operating hours counter has reached its maximum: Press the operating hours control twice and hold it for approx. 6 seconds until only the 1 is flashing.
*INSTALLATION* Installation Before installation Before installation, it is important to read the information given on the following pages as well as the “Warning and Safety instructions” at the beginning of this booklet. Installation instructions See enclosed Installation sheet for instructions on how to install this appliance. Installation materials 1 vent connection for exhaust ducting 150 mm.
*INSTALLATION* Installation Appliance dimensions DA 2808 40
*INSTALLATION* Installation DA 2808 EXT/EXTA 41
*INSTALLATION* Installation a The vent connection can also be connected at the back or to the left-hand side. b 222 x 89 mm flat ducting can be used as an alternative for vent connection to the rear or to the side. c The cooker hood is fastened in the cut-out using clamps. A solid installation surface, e.g. made of wood, is required. Make sure that the structure can support the load. Around the clamps, components such as supports and ducting must be at least 25 mm from the cut-out.
*INSTALLATION* Installation Installation recommendations Uneven installation surfaces - We recommend a minimum distance of 700 mm and a maximum distance of 1300 mm. - Please be aware that if positioned too high, extraction will be inefficient. - To achieve optimum vapour extraction, the cooker hood must be centred over the hob, not to the side or behind it. - The hob should be no wider than the cooker hood, and if possible, it should be narrower.
*INSTALLATION* Installation Connection for air extraction If the cooker hood is used at the Fit one of the screws supplied into each lamp opening. Tighten the screws with a screwdriver until the frame sits flush with the installation surface. Do not overtighten the screws. Replace the lamps. same time as a heating appliance that relies on oxygen from the same room, there is a risk in certain circumstances of toxic fumes building up.
*INSTALLATION* Installation - All connections must be strong and airtight. - If the exhaust ducting has flaps, these must be opened whenever the cooker hood is switched on. Any constriction of the air throughput will reduce extraction performance and increase operating noise. Flue Non-return flap Use a non-return flap in the exhaust system. A non-return flap ensures that when the cooker hood is not in operation, the duct is closed to prevent unwanted exchange of room air and outside air.
*INSTALLATION* Installation Silencer In addition to insulating the exhaust ducting, it is advisable to also install a condensate trap for collecting and evaporating any potential condensation. To reduce noise levels even further, a silencer (optional accessory) can be installed in the exhaust ducting. Condensate traps for 125 mm or 150 mm diameter exhaust ducting are available as optional accessories.
*INSTALLATION* Installation If the socket is no longer accessible after installation, an additional means of disconnection must be provided for all poles. Suitable means of disconnection include switches with an all-pole contact gap of at least 3 mm. These include miniature circuit breakers, fuses and contactors (EN 60335). For operation with an external motor, noise from the motor outside the house and inside the kitchen can be minimised.
Service Contact in the event of a fault In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. You can book a Miele Customer Service Department call-out online at www.miele.com/service. Contact information for the Miele Customer Service Department can be found at the end of this document. Please quote the model identifier and serial number of your appliance (Fabr./ SN/Nr.) when contacting the Miele Customer Service Department.
Technical data Fan motor* 105 W Hob lighting 4x3W Total rated load* Mains voltage, frequency 117 W AC 230 V, 50 Hz Fuse rating 3A Mains connection cable length 1.5 m Weight DA 2808 17 kg DA 2808 EXTA 14 kg * For EXTA models, the rated load will depend on the type of external motor fitted. Length of connection cable to external motor: 1.9 m WiFi module Frequency band Maximum transmission power 2.400–2.
Technical data Conformity declaration Miele hereby declares that this cooker hood complies with Directive 2014/53/EU. The complete text of the EU declaration of conformity is available from one of the following internet addresses: - Products, Download from www.miele.co.uk - For service, information, operating instructions etc: go to www.miele.co.uk/ domestic/customer-information-385.
Technical data Data sheet for household cooker hoods In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
Technical data Data sheet for household cooker hoods In acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86 21 6157 3511 E-mail: info@miele.
DA 2808, DA 2808 EXTA en-GB M.-Nr.
