Operating instructions Coffee System CVA 610 To prevent accidents and machine damage, read these instructions before installation or use. UV M.-Nr.
Contents Contents IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the coffee system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 The program mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Choosing a language . . . . . . . . . . . . .
Contents Coffee system care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Daily care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Stainless steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed, including the following: Read all instructions before installation or use of the coffee system. Electrical safety Please read these instructions carefully to prevent accidents and machine damage. This appliance is for household use only. Any other use is not recommended by the manufacturer and could be dangerous. This appliance complies with current safety requirements.
IMPORTANT SAFETY INSTRUCTIONS Never open the housing of the appliance. If electrical or mechanical components or electrical connections are disturbed, an electric shock could be caused damaging the machine. Before service or maintenance, disconnect the power supply by either removing the fuse, "tripping" the circuit breaker or unplugging the unit from the outlet. Never use a steam cleaner to clean the appliance. Pressurized steam could damage electrical components and cause a short circuit.
IMPORTANT SAFETY INSTRUCTIONS Use The coffee system must be cleaned daily to prevent the growth of harmful bacteria and mold. Please read the "Coffee system care" section of this booklet. Warning: There is a danger of scalding. The nozzles and the liquids dispensed are very hot. The hot water and steam dispensed could cause scalding. These functions must be used carefully. Never direct the steam nozzle towards the body. The machine must never be used to clean objects.
Guide to the coffee system a Hot water dispenser b Coffee dispensers (height-adjustable) c Handle to open appliance front d Steam selector e Steam nozzle with milk frother f Drip catch g Program selector h Message window i Coffee serving buttons j Rinse/ pre-warm button k Hot water button 7
Guide to the coffee system l Coffee bean container m Slide control to select fineness of ground coffee n Slide control to select quantity of ground coffee o Water tank p Waste unit q Brew unit 8
Programming The program mode The coffee system can be customized to each household through the "program mode." To program the appliance: If a setting is accidentally changed, turn the program selector to "0ff". The changed setting will not be saved and the original setting will be retained. ^ Turn the program selector to "Program mode". The appliance is now in program mode and will respond according to the symbols shown under the coffee serving buttons.
Programming Choosing a language The language for the commands in the message window should be selected before the machine is used. The following languages are available: German, Dutch, Portuguese, Spanish, English, Italian, French. ^ Press the e button until the desired language appears (deutsch, nederlands, portugues, espanol, english, italiano or francais.) ^ Press ENTER to save this setting, or turn the program selector to "0ff" to cancel if a mistake has been made.
Programming Rinsing feature The rinsing feature flushes out coffee residue and pre-warms the coffee system. When "Rinsing - On" is selected the system will automatically be flushed and pre-warmed when the appliance is turned on. If this feature is set to "Rinsing - Off" the system will only be flushed and pre-warmed when the rinse/pre-warm button is pressed. ^ Press button e, to turn the "Rinsing" feature on or off.
Programming Determining the water hardness The hardness of the water (tap or bottled) used in the coffee system must be determined and programmed into the appliance. The water hardness will determine how frequently the unit must be descaled to maintain the coffee system properly. The machine monitors the volume of water passing through it in conjunction with the hardness of the water and will indicate when descaling is necessary.
Programming Setting the water hardness ^ Press ENTER to save this setting, or turn the program selector to "0ff" to cancel if a mistake has been made. ^ Turn the program selector counterclockwise to "Program mode". ^ Press the e button to highlight "WATER HARDN." with an asterisk. ^ Press ENTER to select this programming option. The sub-menu will appear in the message window. ^ Press the e button to set the water hardness level (hardness 1 - 4).
Programming Setting the drink temperatures The appliance can be set at different temperatures to suit varying coffee drinking preferences. Five temperature levels are available for each drink option. ^ Turn the program selector counterclockwise to "Program mode". ^ Press the e button to highlight a drink option "TEMP. L. COFFEE" (long), "TEMP COFFEE" (regular) or "TEMP. S. COFFEE" (espresso) with an asterisk. A different temperature can be programmed for each drink. ^ Press ENTER to select the option.
Programming Pre-brewing feature When the pre-brewing feature is on, the freshly ground coffee is moistened with a little hot water to allow the aroma and crema of the coffee to fully develop. The sub-menu will appear in the message window. When the pre-brewing feature is off, the hot water is forced through the coffee immediately. ^ Press the e button to set the pre-brewing process on, off or to "long" (an extra long pre-brew).
Programming Pre-grinding feature The pre-grinding feature allows a new portion of beans to be ground after each coffee is dispensed, so there is always ground coffee ready. This saves time if coffee is dispensed frequently. To preserve aroma, the pre-grinding feature should be turned off when only preparing coffee occasionally. ^ Press the e button to turn the pre-grinding feature on or off. ^ Press ENTER to save this setting, or turn the program selector to "0ff" to cancel if a mistake has been made.
Programming Hot water feature When the feature "Programmed hot water" is turned on, the machine will dispense a precise, pre-programmed quantity of hot water when the hot water button d is pressed. When the feature is turned off, the machine will dispense hot water until the hot water button d is pressed again. ^ Press the e button to set the feature on or off. ^ Press ENTER to save this setting, or turn the program selector to "0ff" to cancel if a mistake has been made.
Programming Total coffee counter The feature "Total coffee" will display the number of cups of coffee (espresso, coffee, long coffee) that have been dispensed to date. ^ Turn the program selector counterclockwise to "Program mode". ^ Press the e button to highlight "TOTAL COFFEE" with an asterisk. ^ Press ENTER to select this option. The number of coffees that have been dispensed will be displayed in the message window. 18 ^ Press ENTER to return to the main menu.
Programming Setting the standby timer For energy efficiency the coffee system can be set to power down after a programmed time interval. The time is measured from the last time coffee / water was dispensed. If the time is set at 0:00, the machine will not switch to standby. ^ Press the e or - button to select the required length of time (e counts down, - counts up). The time can be set in 15 minute periods.
System lock The coffee system can be locked so that it can not be used by children or those not familiar with the operating instructions. Deactivating the system lock Activating the system lock ^ Turn the program selector counterclockwise to the "Lock" position. The following will appear in the message window: ^ Turn the program selector counterclockwise to the "Lock" position. The following will appear in the message window: ^ Press and hold the - button.
Before using the coffee system The appliance must be correctly installed and connected before the first use. Please see the “Installation instructions.” Before using the coffee system, certain parts need to be cleaned and the water lines need to be flushed. ^ Hand wash with hot water and liquid dish soap: – water tank, – coffee bean container, – coffee and hot water dispensers, – steam nozzle. ^ Rinse thoroughly with warm water: – brew unit. See "Coffee system care / Brew unit" for instructions.
Water tank Filling the water tank The water tank must be washed and filled with fresh drinking water before each day of use. A reminder will appear in the message window when the unit is first turned on. ^ Open the lid and fill the container with cold drinking water to within about 1" (2 cm) of the top. Never add hot water or any other liquid except cold water to the water tank. ^ Close the lid and place the tank in the machine, pushing it straight back. ^ Open the front of the machine.
Coffee bean container Filling the coffee bean container Only put pure espresso or coffee beans in the container. Anything else, including ground coffee, hot cocoa, instant coffee, or treated coffee beans (flavorings, caramel, or sugar) will damage the grinder. Do not remove the coffee bean container from the appliance unless it is completely empty, otherwise coffee beans will spill out. ^ Carefully pull the container out as far as it will go so that the lid is visible. Lift the lid.
Setting the serving sizes The flavor of the coffee depends on the type of coffee, how finely the beans are ground and the quantity of water used. To ensure the machine uses exactly the amount of water to suit your taste and your cups, there is a choice of three serving sizes for espresso/coffee. eo1002cq Adjusting the coffee dispensers The height of the coffee dispensers are adjustable to suit different cup sizes. The espresso button a dispenses a standard size espresso.
Setting the serving sizes Coffee and espresso ^ Turn the program selector clockwise to the "On" position (with or without lighting). The following will appear in the message window: ^ Place a cup under the two coffee dispensers. Coffee is always dispensed simultaneously from both spouts. If the machine is cold and the rinsing feature has been selected, the following ^ Press and hold the coffee serving button appropriate to the size of cup until the cup is full as desired.
Setting the serving sizes Hot water To program the volume of hot water dispensed, the hot water feature must be programmed "on". (See "Programming/ Hot water feature"). Once the water is hot, the following appears in the message window: ^ Turn the program selector clockwise to the "On" position (with or without lighting).
Making coffee Pre-warming Pre-warming the system The pre-warm feature allows the system and the cups to be pre-warmed to fully develop the flavor and aroma of your coffee. Pre-warming cups ^ Place a cup or container under the two coffee dispensers. ^ Place the cup under the hot water dispenser. ^ Press the rinse/ pre-warm button e. The following will appear in the message window: ^ Press the hot water button d and half fill the cup. ^ Press the hot water button d again to stop.
Making coffee Espresso or coffee Preparing two cups simultaneously ^ Place a cup under both coffee dispensers. ^ Place a cup under each of the coffee dispensers. 2x ^ Press the desired coffee button once. The coffee will be prepared. The following message will appear in the message window, depending on the button pressed: ^ Press the desired coffee button twice in quick succession to bring up two cups g in the message window. The cups will be filled in two stages with a slight pause in between.
Making coffee Cappuccino Cold, 2% milk is best for creating froth. Ideally it should be prepared in a cold, stainless steel pitcher. ^ As soon as steam appears from the nozzle, shut the steam off by turning the steam selector clockwise, to the "o" position. ^ Fill a third of a small, cold, stainless steel pitcher with cold milk while dispensing espresso. ^ Position the steam nozzle just below the surface of the milk in the pitcher and slowly turn the steam selector counterclockwise.
Making coffee ^ Turn the steam off by turning the steam selector clockwise to the "o" position. ^ Pull the pitcher away from the steam nozzle. Carefully pour the milk into the coffee and spoon some froth onto the surface. Always clean the steam nozzle immediately after use, as it is harder to clean once milk has dried. ^ Dispense a quick spurt of steam into an empty cup. ^ Wipe milk off the nozzle with a damp sponge.
Dispensing hot water Hot water ^ Place a cup under the hot water dispenser. ^ Press the hot water button d. Hot water will be dispensed. ^ Press the hot water button d again to stop the hot water flow. The machine will stop automatically if a volume has been programmed in for hot water and feature "Prog. hot water" is activated.
Setting the coffee grinder Adjusting the coffee grinder To adjust the grinder setting To prevent machine damage, the slide control for the coffee grinder setting should be moved carefully and in small adjustments. – If the espresso flows too quickly into the cup, the beans have been ground too coarsely. The grinder should be adjusted to a finer setting. – If the espresso only trickles into the cup, the beans have been ground too fine and the coffee will be bitter.
Setting the coffee grinder Setting the quantity To adjust the quantity setting: Both the flavor and crema of the coffee depend on the quantity of ground coffee used. The greater the quantity, the stronger the flavor will be. The quality of the crema is also affected by the quantity: – If the crema is evenly colored but pale, increase the quantity setting. – If the crema is very dark brown on one side, graduating almost to white on the other, decrease the quantity setting.
Coffee system care Daily care At the end of each day, the coffee dispensers and the brew unit must be flushed clean. ,Warning! Allow the appliance to cool before cleaning. Hot surfaces can cause burns. The components of the coffee system must be cleaned after each day of use to prevent mold and bacteria growth. ^ Hand wash with hot water and liquid dish soap: – water tank, – coffee and hot water dispensers, – steam nozzle, – waste unit, – drip sponge, ^ Press the Rinse/pre-warm button. – drip catch.
Coffee system care Exterior Interior ^ The exterior can be cleaned with hot water and liquid dish soap applied with a soft sponge. Do not use abrasive cleansers or scrubbers. The interior can be cleaned with hot water and liquid dish soap. Wipe dry using a soft cloth. ^ Wipe dry using a soft cloth. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can also be used.
Coffee system care Drip catch The drip catch has a red float that will rise when the catch is full. The catch should be cleaned when the float rises and at the end of each day to prevent spills and odors. ^ Remove the metal grate and plastic tray from the drip catch and clean by hand with warm water and liquid dish soap. Be careful not to loose the removable float. ^ Open the appliance door. 36 ^ Take the drip catch out of the appliance. Clean it by hand with warm water and liquid dish soap.
Coffee system care Waste unit Steam nozzle Clean the steam nozzle after every use as dried milk residues are difficult to clean. ^ Lift the waste unit up and out. ^ Clean the waste unit by hand with hot water and liquid dish soap and dry with a soft cloth. ^ Loosen the upper screw, a, and pull the sleeve of the steam nozzle down, b. ^ Clean the sleeve with warm water and liquid dish soap (or in the dishwasher) and dry. ^ Push the waste unit back into place, positioning it over the notches.
Coffee system care Brew unit Clean the brew unit by hand only. The moving parts and the rubber gaskets can not be cleaned in a dishwasher. ^ Dry the funnel to prevent ground coffee from sticking. ^ After cleaning press "PRESS". Lubricate the brew unit with the enclosed silicon every 500 cups (see "Lubricating the brew unit"). ^ Remove the waste unit. The brew unit can only be removed after the waste unit has beeen taken out. ^ Grasp the brew unit by the handle and press with the thumb on "PRESS".
Coffee system care Rinsing cycle: Degreasing the brew unit The natural oil found in coffee can cause the brew unit to clog. The message "Rinsing cycle" will flash in the message window after 500 cups to remind you to clean the unit with the enclosed detergent tablets. These speciality cleaning tablets can be purchased from your Miele dealer or the Technical Service Department. The display will read: ^ Press e, to select "Rinsing cycle" with the asterisk. ^ Press ENTER.
Coffee system care Cleaning the brew unit filters ^ Wipe away coffee residues from the steel filter in the funnel of the brew unit with a sponge. The chrome filter to the left of the funnel can be removed for thorough cleaning. Check and clean the chrome filter regularly. ^ Remove the brew unit. ^ Fit the enclosed allen wrench to the connection point in the brew unit. Turn counterclockwise while supporting the chrome filter from below. ^ Remove the chrome filter with the screw.
Coffee system care Lubricating the brew unit ^ Remove the brew unit. ^ Clean the bolt, a. Lubricate the bolt, a, and the joints, b. Check that the brew unit is in the basic position with the funnel slightly lifted and the socket in vertical position (see illustration.) ^ Return the brew unit into the appliance. ^ Lubricate the joints a, the axle b, the tracks c and the gasket d with the silicon grease.
Coffee system care Resetting the brew unit’s basic position: Change the gaskets ^ Press on the latch, a, and press the funnel down, b. ^ Change the gaskets if a leak occurs. ^ Push the connection piece to the far left, c. ^ Press "PRESS" once. The basic position shown above is reset and the brew unit can be set back into the machine. 42 Three gaskets are enclosed with the machine. One gasket is located between the steam nozzle and the sleeve.
Coffee system care Changing the light bulb ^ Disconnect power to the appliance by unplugging the appliance, tripping the circuit breaker or removing the fuse. ^ Open the appliance door. ^ Carefully push the bulb into position until it clicks into the holder, a, and turn it upwards, b. ^ Close the lamp cover. ^ Insert a small screw driver into the opening and carefully push upwards, a. ^ At the same time pull the light cover down, b. ^ Rotate the bulb forward, a, and carefully pull it out, b, towards you.
eo1404cq Descaling the appliance The coffee system must be descaled regularly. The appliance will display a reminder message to descale and will eventually lock if not descaled. The message window will first display: "DESCALE AFTER COFFEES: 100“. This message will appear until the appliance is descaled or it locks. When the count is at zero, the appliance locks and the message window displays: ^ Add 1 liter of water to the water tank. Dissolve two of the enclosed descaling tablets in the water.
Descaling the appliance The coffee system will begin the automatic descaling. The display will read: ^ Press ENTER. The message window will read: Do not open the door during descaling and do not turn the program selector to "0". This will interrupt the descaling process. If the process is interrupted, add water to the reservoir, turn the program selector back to "Program mode" and close the door. Also, empty the containers under the dispensers and steam nozzle as more water will be expelled.
Descaling the appliance ^ Turn the steam selector clockwise to position "0" and press ENTER. ^ Turn the steam selector clockwise to position "o". ^ Press ENTER. The display will read: The machine needs to be rinsed to clean out the descaling residue. ^ Fill the water tank three quarters of the way with cold water and place back into the machine. ^ Place the empty 1 liter containers below the hot water dispenser and the steam nozzle and turn the steam selector counterclockwise.
eo1505cq Fault messages If an error occurs a fault message will appear. With the following guide, minor problems can be fixed without a service call. Message Possible fault Fix Fill coff. beans Ready for use Coffee bean container is empty. Refill with coffee beans. Brew unit block. The brew unit is clogged. Clean the brew unit. Brew unit miss. The brew unit is not properly seated. Take out the brew unit and reseat. Descale The unit needs to be descaled. Descale the unit.
Frequently asked questions What if... Possible fault . . . there is no prompt The unit has no in the message power. window? . . . the light does not illuminate? – Is the door open? – Is the unit in standby mode? – Is the unit locked? Fix Is the door closed? Check that the circuit has not tripped, the fuse has blown or that the appliance is unplugged. Otherwise contact the Miele Technical Service Department. If not, the light bulb has burned out. See "Changing the light bulb". . . .
Frequently asked questions What if... Possible fault Fix . . . the espresso is dispensed too quickly? The grinder is set to Select a finer setting. too coarse of a setting. . . . the espresso is dispensed too slowly? The grinder is set to Select a coarser setting. too fine of a setting. . . . the coffee is not hot enough? Was the system warmed? Pre-warm the system and cups. Check the temperature setting of the coffee selected. Check if the brew unit is clogged. Clean the brew unit. . . .
Frequently asked questions What if... Possible fault . . . no water runs out of the dispensers? The brew unit is clogged. Clean the brew unit filters. . . . there is no crema? Check if the grinder is set Adjust the coffee grinder to the coarsest or to the setting. finest setting. The coffee is not fresh. Fix Use fresh coffee beans. The coffee dispensers are Lower the height adjustset too high. able dispensers. Check the temperature setting of each drink option.
After sales service In the event of a fault which you cannot correct yourself please contact: – Your Miele Dealer or – The Miele Technical Service Department USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions
Contents Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Disposal of the packing materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Disposal of an old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Installation . . . . . . . . . . . . .
Caring for the environment Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances may contain materials that can be recycled.
Electrical connection ,Ensure that power to the appliance is OFF while installation or repair work is performed. All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer can not be held responsible for unauthorized work.
Installation Installation options The coffee system is designed to be built into cabinetry.
Installation The coffee system can be installed above another appliance but, there must be a solid, closed shelf between the base of the coffee machine and the top of the appliance below (The shelf is not necessary when installation is in combination with the Miele built-in plate warmer).
Installation A speciality display cabinet is also available from your dealer or Miele’s Technical Service Department, as an installation option. Please quote part # 29996001 when ordering.
Installation ,Make sure power is not supplied to the appliance while installation or maintenance work is performed. Disconnect the power supply to the work area by unplugging the unit, tripping the circuit breaker or removing the fuse. The coffee system must be installed into cabinetry before being operated. ^ Plug the appliance into the electrical outlet. ^ Push it all the way back into the cabinet, until there is a resistance. ^ Open the front of the machine and partially tighten the screws.
Glossary Arabica is a high quality coffee bean. It is long and flat with a groove running around it. The caffeine content is between 0.8 - 1.3%. It is strong and aromatic, but less bitter than the Robusta bean. Caffè is the Italian term for a standard espresso. Caffè americano is a thin espresso with water added. Caffè corretto is espresso with a dash of something stronger such as grappa, brandy or a liqueur. Cappuccino scuro is a "dark" cappucino with more espresso and less milk.
Alteration rights reserved / 44 / 000 / CDN / USA - 4902 This paper consists of cellulose bleached without the use of chlorine. M.-Nr.
