User manual
Table Of Contents
- Contents
- Caring for the environment
- Warning and Safety instructions
- Operating the washing machine
- Before using for the first time
- Washing environmentally and economically
- 1. Prepare the laundry
- 2. Select a programme
- 3. Load the washing machine
- 4. Select programme settings
- 5. Add detergent
- 6. Starting the programme
- 7. End of programme
- Spinning
- Programme chart
- Garment care label symbols
- Extra options
- Wash programme chart - Extras
- Programme sequence
- Changing the programme sequence
- Detergent
- The correct detergent
- The right amount to dispense will depend on the following:
- Water softeners
- Dispensing aids
- Refill packs of detergent
- Fabric conditioner and liquid starch
- Adding fabric conditioner or liquid starch separately
- Colour run and dye removers/dyes
- Recommended Miele detergents
- Recommended detergents in accordance with Directive (EU) Nr. 1015/2010
- Replacing the TwinDos cartridge
- Cleaning and care
- Problem solving guide
- The programme does not start
- Fault message after a programme has been interrupted.
- Fault message at the end of a programme
- Fault message at the end of a programme
- Messages or faults with the TwinDos system
- Messages or faults with the TwinDos system
- General problems with the washing machine
- General problems with the washing machine
- An unsatisfactory wash result
- The door will not open
- Opening the door in the event of a blocked drain outlet and/or power cut
- Service
- Installation
- Consumption data
- Technical data
- Settings
- Accessing the Settings menu
- Selecting settings
- Changing a setting
- Closing the settings menu
- _
- TwinDos
- Degree of soiling
- Buzzer volume
- Keypad tone
- Welcome tone
- Consumption
- Code
- Units
- Brightness
- Disp. switch-off stat.
- Programme info
- Memory
- Long p-wash Cotton
- Soak duration
- Gentle action
- Temp. reduction
- Water plus
- Water plus level
- Maximum rinse level
- Suds cooling
- Low water pressure
- Anti-crease
- Miele@home
- _
- SmartGrid
- RemoteUpdate
- Copyrights and licences for the communication module
- Detergents and care products
Before using for the first time
20
3. Remove the transit bars
Damage resulting from failure to
remove the transit bars.
Failure to remove the transit bars can
result in damage to the washing ma-
chine and to adjacent cabinetry or
appliances.
Remove the transit bars as described
in “Installation and connection”.
The following message appears in the
display:
Remove transit bars
Confirm with the OKsensor control.
4. Commissioning TwinDos
The UltraPhase1 and UltraPhase2 val-
ues are preset in the standard settings
and only need to be confirmed.
The following message appears in the
display:
TwinDos
Confirm with the OKsensor control.
The following message appears in the
display:
Set now
To set up TwinDos now, touch the OK
sensor control.
To postpone setup until later: touch
the sensor control until the follow-
ing appears in the display: Set later
and pressOK to confirm.
Settings for compartment
The UltraPhase1 values are preset in
the standard settings.
Agent for
OK
Confirm with the OKsensor control.
Miele UltraPhase 1
OK
Confirm with the OKsensor control.
The following appears in the display:
Set the dosage. Observe water hardness
levels
Confirm with the OKsensor control.
The dispensing quantity for
UltraPhase1 is preset for (hardness
level II).
Per load
OK
ml58
Confirm the preset value with the
OKsensor control. If you want to
change this value, use the
sensor controls and confirm with
the OK sensor control.
UltraPhase1
Hardness level I 46ml
Hardness level II 58ml
Hardness level III 70ml