User manual
Table Of Contents
- Contents
- Caring for the environment
- Warning and Safety instructions
- Operating the washing machine
- Before using for the first time
- Washing environmentally and economically
- 1. Prepare the laundry
- 2. Select a programme
- 3. Load the washing machine
- 4. Select programme settings
- 5. Add detergent
- 6. Starting the programme
- 7. End of programme
- Spinning
- Delay start/SmartStart
- Programme chart
- Extra options
- Garment care label symbols
- Programme sequence
- Changing the programme sequence
- Detergent
- The correct detergent
- The right amount to dispense will depend on the following:
- Water softeners
- Water hardness levels
- Dispensing aids
- Refill packs of detergent
- Colour run and dye removers/dyes
- Fabric conditioner and liquid starch
- Recommended Miele detergents
- Recommended detergents in accordance with Directive (EU) Nr. 1015/2010
- Replacing the TwinDos cartridge
- Cleaning and care
- Problem solving guide
- The programme does not start
- The programme is cancelled and a fault indicator light lights up in the control panel
- During the programme sequence, a symbol appears in the time display
- At the end of the programme, an indicator light lights up in the control panel
- Messages or faults with the TwinDos system
- General problems with the washing machine
- General problems with the washing machine
- An unsatisfactory wash result
- The door will not open
- Opening the door in the event of a blocked drain outlet and/or power cut
- Service
- Installation
- Technical data
- Consumption data
- Programmable functions
- Opening the programming level
- Choosing and selecting a programmable function
- Editing and saving a programmable function
- Exit programming level
- Sensor tone
- Lock code
- Control panel switch-off status
- Memory
- Longer pre-wash Cottons
- Gentle action
- Reduce temperature
- Maximum rinse level
- Suds cooling
- Anti-crease
- Low water pressure
- Backlight brightness dimmed
- TwinDos
- UltraPhase 1 dispensing quantity
- UltraPhase 2 dispensing quantity
- TwinDos maintenance
- Degree of soiling
- Networking
- Remote control
- SmartGrid
- RemoteUpdate
- Switching off WiFi
- Copyrights and licences for the communication module
- Detergents and care products
Installation
*INSTALLATION*
74
Connection to the water supply
Connecting the water inlet
Health risk and risk of damage
due to contaminated incoming water.
The quality of the incoming water
must correspond to the drinking wa-
ter specification of the country in
which the washing machine is being
operated.
Always connect the washing ma-
chine to the mains water supply.
The water connection pressure needs
to be between 100 and 1000kPa. If the
water connection pressure exceeds
1000kPa, a pressure reducing valve
must be installed.
A stopcock with a ¾inch threaded
union is required for the connection. If
this is not available, only a qualified in-
staller may connect the washing ma-
chine to the mains water supply.
The screw thread is subject to water
connection pressure.
Check the connection for leaks.
Slowly open the stopcock. Correct
the position of the seal and screw
thread if necessary.
The washing machine is not suitable
for connection to a hot water supply.
The washing machine must not be
connected to a hot water supply.
Maintenance
Only use a genuine Miele hose that has
been pressure tested to withstand at
least 7,000kPa should you ever need a
replacement.
Damage caused by dirty water.
A filter is located in the open end of
the inlet hose and another in the in-
take point to protect the inlet valve in
the washing machine.
These filters must not be removed.
Hose extension
Longer hoses 2.5 or 4.0m in length are
available from your Miele Dealer or
Miele as optional extras.