User manual
Table Of Contents
- Contents
- Warning and Safety instructions
- Operating the washing machine
- Caring for the environment
- Before using for the first time
- Washing environmentally and economically
- 1. Prepare the laundry
- 2. Load the washing machine
- 3. Select a programme
- 4. Add detergent
- 5. Start the programme
- 6. End of programme
- Spinning
- Delay start
- Programme chart
- Extra options
- Programme sequence
- Changing the programme sequence
- Garment care label symbols
- Detergent
- The correct detergent
- The right amount to dispense will depend on the following:
- Water softeners
- Water hardness levels
- Dispensing aids
- Refill packs of detergent
- Fabric conditioner and liquid starch
- Using fabric conditioner or starch separately
- Colour run and dye removers/dyes
- Recommended Miele detergents
- Recommended detergents in accordance with Directive (EU) Nr. 1015/2010
- Cleaning and care
- Problem solving guide
- The programme does not start
- The programme is cancelled and a fault indicator light lights up in the control panel
- During the programme, a symbol appears in the time display
- At the end of the programme, an indicator light lights up in the control panel
- General problems with the washing machine
- General problems with the washing machine
- An unsatisfactory wash result
- The door will not open
- Opening the door in the event of a blocked drain outlet and/or power cut
- Service
- Installation
- Technical data
- Consumption data
- Programmable functions
- Opening the programming level
- Choosing and selecting a programmable function
- Editing and saving a programmable function
- Exit programming level
- Buzzer duration
- Buzzer
- Sensor tone
- Lock code
- Control panel switch-off status
- Memory
- Longer pre-wash Cottons
- Gentle action
- Reduce temperature
- Water plus
- Water plus level
- Maximum rinse level
- Suds cooling
- Anti-crease
- Low water pressure
- Backlight brightness dimmed
- Operating hours
- Factory default
- Detergents and care products
Spinning
28
Final spin speed in wash pro-
grammes
When a programme is selected, the
sensor control for the optimum spin
speed for that programme will be
brightly lit up in the control field.
A faster spin speed can be selected for
certain wash programmes.
The highest selectable spin speed is in-
dicated in the table.
Programme rpm
ECO 40-60 1400
Cottons 1400
Minimum iron 1200
Delicates 900
Woollens 1200
Shirts 900
Express 20 1200
Dark garments/Denim 1200
Outerwear 900
Proofing 1200
Drain/Spin 1400
Separate rinse/Starch 1200
Rinse and interim spin
There is a spin after the main wash and
between the rinses. A reduction in the
final spin speed will also reduce the in-
terim spin speed. If a spin speed of less
than 700 rpm is selected for the Cot-
tons programme, an additional rinse is
introduced.
Selecting Rinse hold (final spin)
Touch the sensor control (Rinse
hold).
The laundry is not spun after the final
rinse and remains in the rinse water.
This helps to prevent creasing if the
laundry is not going to be removed from
the drum immediately after the end of
the programme.
Ending a programme with a spin
cycle
The sensor control for the optimum spin
speed lights up on the control field. You
can change the spin speed.
Touch theStart/Add laundry sensor
control.
Ending a programme without a spin
cycle
Reduce the spin speed to 0.
Touch theStart/Add laundry sensor
control.
To omit rinse and interim spin
and the final spin
Touch the sensor.
After the last rinse, the water will be
pumped away and the anti-crease
phase will switch in.
In some programmes an additional rinse
is introduced with this setting.